Juniper SRX-4600 Manuel utilisateur
Quick Start
SRX4600 Quick Start
IN THIS GUIDE
Step 1: Begin | 1
Step 2: Up and Running | 5
step-3-keep-going | 8
Step 1: Begin
IN THIS SECTION
Mount the SRX4600 | 2
Connect the SRX4600 to Ground | 3
Connect Power to the SRX4600 | 3
To mount, connect power to, and perform inial conguraon on the Juniper Networks® SRX4600 Firewall, you need:
•Electrostac discharge (ESD) grounding strap (not provided)
• Four-post rack-mounng kit (provided)
• Twelve screws to secure the mounng rails and mounng blades to the chassis (provided)
• Eight screws to secure the chassis to the rack (not provided)
• Screwdriver appropriate for your rack-mounng screws (not provided)
• Two AC power cords with plugs appropriate for your geographical locaon (provided)
• Management host, such as a PC or laptop, with a serial port (not provided)
• A grounding cable (minimum 14 AWG (2 mm²), minimum 90°C wire), a grounding lug (Panduit LCD10-10A-L or
equivalent) (not provided).
• RJ-45 cable and RJ-45 to DB-9 serial port adapter (not provided)
NOTE: We no longer include a DB-9 to RJ-45 cable or a DB-9 to RJ-45 adapter with a CAT5E copper cable
as part of the device package. If you require a console cable, you can order it separately with the part number
JNP-CBL-RJ45-DB9 (DB-9 to RJ-45 adapter with a CAT5E copper cable).
Mount the SRX4600
You can mount an SRX4600 Firewall in a 19-inch four-post rack conguraon. An AC device weighs approximately 38
lb (17.23 kg) and a DC device weighs approximately 40 lb (18.14 kg). Two persons are required for mounng the device.
To mount the rewall:
1. Aach the ESD grounding strap to your bare wrist and to a site ESD point.
NOTE: If you are mounng mulple units in the rack, mount the heaviest unit at the boom and mount the
others from boom to top in order of decreasing weight.
2. Place the rack in its permanent locaon, allowing adequate clearance for airow and maintenance, and secure it to
the building structure.
3. Aach the front-mounng brackets to the side mounng rails by using the Phillips 4-40 at-head mounng screws.
4. Align the holes in the side mounng rails with the holes on the side of the chassis and aach the side mounng rails
to the chassis by using the mounng screws.
5. Have one person grasp both sides of the device, li it, and posion it in the rack so that the front bracket is aligned
with the rack holes and the second person secure the front of the device to the rack by using four mounng screws.
6. Have the second person use the mounng screws (and cage nuts and washers if your rack requires them) to screw
the mounng bracket to the rack.
2
7. Connue to support the device and slide the rear mounng blades into the channel of the side mounng rails and
securing the blades to the rack. Use the four mounng screws (cage nuts and washers if the rack requires) to aach
each blade to the rack.
8. Aach a grounding cable to earth ground and then aach it to the chassis grounding points.
Connect the SRX4600 to Ground
To connect the Firefall to the ground:
1. Aach an ESD grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis.
2. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the services gateway is
mounted.
3. Place the grounding lug aached to the grounding cable over the protecve earthing terminal on the protecve
earthing terminal bracket.
4. Secure the grounding lug to the protecve earthing terminal with the washers and screws.
5. Dress the grounding cable and ensure that it does not touch or block access to other device components and that it
does not drape where people could trip over it.
Connect Power to the SRX4600
IN THIS SECTION
Connect Power to an AC-powered SRX4600 | 4
Connect Power to a DC-powered SRX4600 | 4
3
NOTE: Check if the power supplies AC or DC are fully inserted into the chassis.
Connect Power to an AC-powered SRX4600
To connect power to an AC-powered Firewall:
NOTE: An AC-powered device gets addional grounding when you connect the power supply in the device to a
grounded AC power outlet by using the power cord.
1. Insert the coupler end of the power cord into the AC power cord inlet on the AC power supply faceplate. Push the
power cord retainer onto the power cord.
2. Insert the power cord plug into an AC power source outlet:
a. If the AC power source outlet has a power switch, set it to on (|) posion and the Firewall will power on.
b. If there is no power switch on the AC power source outlet, the services gateway will power on instantly.
3. Verify that the OK/FAIL LED is lit green and on steadily.
Connect Power to a DC-powered SRX4600
To connect power to a DC-powered Firewall:
WARNING: Before performing the following procedure, ensure that there is no power in the DC circuit.
To ensure that all power is cut o, locate the circuit breaker on the panel board that services the DC
circuit, switch the circuit breaker to the o (0) posion, and tape the switch handle of the circuit
breaker in the o posion.
1. Ensure that the voltage across the DC power source cable leads is 0 V and that the cable leads do not become acve
while you are connecng DC power.
2. Verify that the DC power cables are correctly labeled before connecng them to the power supply. In a typical
power distribuon scheme where the return is connected to chassis ground at the baery plant, you can use a
mulmeter to verify the resistance of the –48V and RTN DC cables to chassis ground:
a. The cable with very high resistance (indicang an open circuit) to chassis ground is negave (–) and is installed on
the –48V (input) DC power input terminal.
4
b. The cable with very low resistance (indicang a closed circuit) to chassis ground is posive (+) and is installed on
the RTN (return) DC power input terminal.
3. Remove the protecve cover from the DC power input terminal block. Save this cover for future use.
4. Remove the M5 K-nuts from each DC power input terminal.
5. Aach DC terminal rings (TYCO 2-36161-2 Terminal Ring, number 10, not provided) to the ends of the DC power
cables. Crimp ghtly.
6. Insert the DC terminal rings into the DC power input terminals and secure the DC terminal rings with M5 K-nuts. Do
not overghten.
7. Replace the protecve cover over the input terminal block.
8. Remove the tape from the switch handle of the circuit breaker on the panel board that services the DC circuit, and
switch the circuit breaker to the ON (|) posion.
9. Verify that the OK/FAIL LED is lit green and on steadily.
Step 2: Up and Running
IN THIS SECTION
Set Parameter Values | 5
Perform the Inial Conguraon | 6
Set Parameter Values
You must perform the inial conguraon of the device through the console port. Before you begin, set the following
parameter values in the console server or the management host:
• Baud Rate—9600
• Flow Control—None
• Data—8
5
• Parity—None
• Stop Bits—1
• DCD State—Disregard
Perform the Inial Conguraon
To connect and congure the Firewall from the console:
1. Connect the console port (CON), located on the front panel of the SRX4600 to a laptop or PC by using the
provided RJ-45 cable and RJ-45 to DB-9 serial port adapter (not provided).
2. Log in as root. There is no password. If the soware booted before you connected to the console port, you might
need to press the Enter key for the prompt to appear.
login: root
3. Start the CLI.
root# cli
root@>
4. Enter conguraon mode.
root@> configure
5. Set the root authencaon password by entering either a cleartext password, an encrypted password, or an SSH
public key string (DSA or RSA):
[edit]
root@# set system root-authentication plain-text-password
New password:
password
Retype new password:
password
6. Congure an administrator account on the device. When prompted, enter the password for the administrator
account:
[edit]
root@# set system login user admin class super-user authentication plain-text-password
6
New password:
password
Retype new password:
password
7. Commit the conguraon to acvate it on the device:
[edit]
root@# commit
8. Log in as the administrave user you congured in Step 6.
9. (Oponal) Congure the name of the device. If the name includes spaces, enclose the name in quotaon marks (“ ”):
[edit]
admin@# set system host-name
host-name
10. Congure the IP address and prex length for the management interface on the Firewall.
[edit]
admin@# set interfaces fxp0 unit 0 family inet address
address/prefix-length
11. Congure the default route.
[edit]
admin@# set routing-options static route 0.0.0.0/0
next-hop gateway
12. Check the conguraon for validity:
[edit]
admin@# commit check
13. Commit the conguraon to acvate it on the device:
[edit]
admin@# commit
7
step-3-keep-going
IN THIS SECTION
What's Next | 8
General Informaon | 9
Learn With Videos | 9
Congratulaons! You’ve completed the inial steps to get your ACX7024 up and running. Let’s keep going and learn
more about what you can do with the ACX7024.
What's Next
Now that you've done the inial conguraon, here are some things you might want to do next.
If you want to Then
Congure the ACX7024 with the Junos OS Evolved CLI Start with the Day One+ for Junos OS Evolved guide
Install and upgrade Junos OS Evolved and related soware See Junos OS Evolved Soware Installaon and Upgrade Guide
Acvate, and manage your soware licenses to unlock
addional features for your ACX7024 router
See Acvate Junos OS Licenses
Congure, monitor, and troubleshoot various interfaces on the
ACX7024
See Ethernet Interfaces User Guide for Roung Devices
Congure essenal user access and authencaon features for
your system
See User Access and Authencaon Administraon Guide for
Junos OS Evolved
8
General Informaon
If you want to Then
See all documentaon available for the SRX4600 See the SRX4600 Documentaon in the Juniper Networks
TechLibrary
Stay up-to-date about new and changed features, and known
and resolved issues
Junos OS Release Notes
Learn With Videos
Our video library connues to grow! We’ve created many, many videos that demonstrate how to do everything from
install your hardware to congure advanced Junos OS network features. Here are some great video and training
resources that will help you expand your knowledge of Junos OS.
If you want to Then
Get short and concise ps and instrucons that provide quick
answers, clarity, and insight into specic features and funcons
of Juniper technologies
See Learning with Juniper on Juniper Networks main YouTube
page
Learn how to install and congure your Juniper Networks
devices
Check out our free Web-based training videos at Hardware
Installaon and Conguraon Videos
View a list of the many free technical trainings we oer at
Juniper
Visit the Geng Started page on the Juniper Learning Portal
Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in the
United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the
property of their respecve owners. Juniper Networks assumes no responsibility for any inaccuracies in this document.
Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publicaon without noce.
Copyright © 2023 Juniper Networks, Inc. All rights reserved.
9
Autres manuels pour SRX-4600
2
Table des matières
Autres manuels Juniper Porte
Juniper
Juniper SSG5 Manuel utilisateur
Juniper
Juniper SRX5600 Instructions d'installation
Juniper
Juniper SRX Series Manuel utilisateur
Juniper
Juniper SRX320 Instructions d'installation
Juniper
Juniper SRX345 Instructions d'installation
Juniper
Juniper SRX3600 Instructions d'installation
Juniper
Juniper VGW VIRTUAL GATEWAY Manuel utilisateur
Juniper
Juniper SRX380 Manuel utilisateur
Juniper
Juniper SRX 5800 Manuel utilisateur
Juniper
Juniper SRX550 Instructions d'installation
Juniper
Juniper SRX650 Manuel utilisateur
Juniper
Juniper SRX300 Series Instructions d'installation
Juniper
Juniper SRX 5800 Instructions d'installation
Juniper
Juniper SRX110 Instructions d'installation
Juniper
Juniper SRX650 Mode d’emploi
Juniper
Juniper SRX380 Manuel utilisateur
Juniper
Juniper SRX3400 Manuel utilisateur
Juniper
Juniper SRX340 Manuel utilisateur
Juniper
Juniper SRX 5800 Manuel utilisateur
Juniper
Juniper SRX1500 Guide de configuration
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
