Johnson Controls NXT-INT-01 Manuel utilisateur

INSTALLATION GUIDE

Installing and Operating the NXT-INT-01 Intelligent Thermostat

Introduction

The Intelligent Thermostat has a space

temperature sensor, five user push buttons,

and a 2 line x 8 character dot matrix LCD

to show room temperature, time, outside air

temperature, setpoint, and other optional

parameters (depending upon the operation).

NXT-INT-01 Intelligent Thermostat

OVERRIDE

ROOM/

OUTSIDE

72 ° F

RoomTemp

Figure 2 - Wiring connection for the Intelligent Thermostat

www.johnsoncontrols.com

LIT-TD-2006 11/2002

Literature Part # 24-9869-5 Rev. A

Figure 1 - NXT-INT-01 Intelligent Thermostat

Installation

The thermostat connects to the controllers

via a 2-wire (#22 AWG, single twisted pair)

cable. The NexSys thermostat communica-

tions bus carries power and communica-

tions for the Intelligent thermostat.

Wiring

WARNING - TO PREVENT ELECTRI-

CAL SHOCK OR DAMAGE TO THE

EQUIPMENT, YOU MUST DISCON-

NECT THE POWER SUPPLY TO THE

ELECTRONICCONTROLLER

BEFORE YOU MAKE THE WIRING

CONNECTIONS.

All wiring is low voltage and should be in

accordance with local regulations and the

National Electrical Code.

Use shielded cable only when it is required.

Most applications do not require shielding

and will benefit from unshielded cable.

When using the optional shielded cable,

ground only one end of the shield. Low

voltage control wiring should not be run in

the same conduit as line voltage wiring or

other conductors that supply highly-

inductive loads (such as contactors, coils,

motors, generators, etc.).

CAUTION - MAKE ALL CONNEC-

TIONS AND CHECK ALL CONNEC-

TIONS BEFORE APPLYING

POWER. IMPROPER WIRING MAY

CAUSE PERMANENT DAMAGE TO

THIS EQUIPMENT.

Wiring Recommendations

Unshielded

Stranded, 22AWG: Belden #8442(2-

wire), Belden #8444(4-wire)

Plenum-rated, Stranded, 22AWG: Belden

#82442(2-wire), 82444(4-wire)

Stranded, 18AWG: Belden #8461(2-

wire), Belden #8489(4-wire)

Plenum-rated, Stranded, 18AWG: Belden

#87740(2-wire), 82489(4-wire)

Shielded

Stranded: Belden #8761

Solid: Belden #8450

Plenum-rated, Stranded: Belden

#88761other equipment.

To Wire the Intelligent Thermotat:

1. Connect the Red wire of the stat’s pigtail

to the STAT + terminal of the controller.

2. Connect the Black wire of the stat’s

pigtail to the controller’s STAT - terminal.

Refer to Figure 2 below.

Mounting

Mount the thermostat where it is exposed

to normal air circulation and where it senses

the average temperature of the space being

controlled (normally about 5 feet above the

floor). Do not mount it where it could be

affected by heat or cold from windows,

pipes, doors, lamps, sunlight, outside walls,

or other sources. See Figure 3 for dimen-

sions.

Figure 3 - Intelligent Thermostat dimensions

ST- ST+ NET- NET+

RED

BLACK

Electronic Systems USA, Inc.

OVERRIDE

ROOM/

OUTSIDE

72 ° F

RoomTemp

Room Sensor Installation - Page 2

Installation and Operation - Page

Repairs and Replacement

Do not make field repairs. Please

contact Johnson Controls at (800) 765-

7773 for replacement and other services.

Johnson Controls, Inc. reserves the

right to update specifications when

appropriate. Information contained in

this document is based on specifica-

tions believed to be correct at the

time of publication.

Figure 4 - Mounting the Intelligent Thermostat

LIT-TD-2006 11/2002

Literature Part # 24-9869-5 Rev. A

To mount the thermostat:

1. Install a 2” x 3” outlet box and the wiring

from the NexSys controller.

2. Pull the wiring from the outlet box and

insert it through the mounting bracket.

3. Assemble the mounting bracket to the

outlet box.

4. Connect the 2-wire pigtail from the

thermostat to the wires in the wall and

secure them with wire nuts. Obey wiring

polarity (see Figure 2).

5. Push excess wire into the outlet box.

6. Snap the cover onto the mounting

bracket.

Operation

Startup

Once activated, the Intelligent Thermostat

will display “ESUSA” then “Init. . .”

(initializing) on the LCD display window.

After five seconds, the thermostat will

send the current temperature and request

the Home Page parameter to update its

display.

If the thermostat detects a communica-

tions failure, “Com Fail” will display in the

display window for five seconds. “Retry”

will display when the thermostat attempts

to communicate again. Should the

thermostat detect a hardware or EEPROM

error, “Error” displays in the window.

Modes

The Intelligent Thermostat has three

operating modes: User, Configuration, and

Balance.

User Mode - In User Mode, the thermo-

stat samples the space temperature and

allows the occupant to adjust the setpoint,

display parameters, and activate the

Override function.

Configuration Mode - A technician

accesses this mode by entering a password

value using the buttons on the thermostat.

In this mode, the thermostat becomes a

basic configuration tool that allows a

technician to view and/or edit the

controller’s configuration and all its

operating parameters.

Balance Mode - A technician accesses

this mode by entering a password value

using the buttons on the thermostat. This

mode allows a technician to adjust the

mechanical attributes of the entire VAV

system in order to bring the system into

proper operation.

This thermostat also provides an access

point to connect a PDA or laptop to the

thermostat communications bus. These

devices can then be used to command the

thermostat to Standby mode for one

minute periods.

www.johnsoncontrols.com

Table des matières

Autres manuels Johnson Controls Thermostat

Johnson Controls

Johnson Controls TEC2103-1 Manuel utilisateur

Johnson Controls

Johnson Controls NXT-TSO-01 TSO Manuel utilisateur

Johnson Controls

Johnson Controls TEC3000 Series Manuel utilisateur

Johnson Controls

Johnson Controls Hx 3 S1-THXU430W Manuel utilisateur

Johnson Controls

Johnson Controls NXA-FCU-01 Manuel utilisateur

Johnson Controls

Johnson Controls T6634-TE21 Manuel utilisateur

Johnson Controls

Johnson Controls GLAS Manuel de service

Johnson Controls

Johnson Controls T6000 Series Manuel utilisateur

Johnson Controls

Johnson Controls TEC2004-4 Manuel utilisateur

Johnson Controls

Johnson Controls GLAS Manuel utilisateur

Johnson Controls

Johnson Controls TEC2145-4 Manuel utilisateur

Johnson Controls

Johnson Controls T28 Manuel utilisateur

Johnson Controls

Johnson Controls TEC3000 Series Manuel utilisateur

Johnson Controls

Johnson Controls T9580 Mode d'emploi

Johnson Controls

Johnson Controls TEC2103-1 Manuel utilisateur

Johnson Controls

Johnson Controls A19A Manuel utilisateur

Johnson Controls

Johnson Controls S1-THXU280 Manuel utilisateur

Johnson Controls

Johnson Controls S1-THXU280W Guide de démarrage rapide

Johnson Controls

Johnson Controls A19BAC Manuel utilisateur

Johnson Controls

Johnson Controls TEC2104-1 Manuel utilisateur

Johnson Controls

Johnson Controls ACC-WIFI Manuel utilisateur

Johnson Controls

Johnson Controls TEC3330-1 Series Manuel utilisateur

Johnson Controls

Johnson Controls T600HPP-2 Manuel utilisateur

Johnson Controls

Johnson Controls T9200 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur