Johnson Controls T28 Manuel utilisateur
Installation Instructions T28
Issue Date 02/01/02
© 2002 Johnson Controls, Inc. 1
Part No. 24-9715-0, Rev. A www.johnsoncontrols.com
T28 Fan Coil Thermostat
Application Requirements
The T28 thermostats control line voltage fan coil units
and zone valves on heating, cooling, and a
combination of heating and cooling equipment. The
thermostats directly control one or two zone valves.
Thermostats with fan switches require a two-gang
switch box at least 2 1/2 in.-deep, or a 4 in. by 4 in. or
larger junction box with a two-fixture plaster ring. For
example, use Raco No. 230 or Appleton No.4SD1/2
two-gang switch box, plus plaster ring.
Thermostats without fan switches require a 2 in.-deep
single, vertical switch box or a larger box with a
single-fixture plaster ring. For example, use Raco
No. 420 or Appleton No. 111 single switch box.
Note: The boxes and plaster rings are not included
with the thermostat.
Installation
IMPORTANT: The T28 Series Thermostats are
intended to control equipment under normal
operating conditions. Where failure or malfunction of
a T28 thermostat could lead to an abnormal
operating condition that could cause personal injury
or damage to the equipment or other property, other
devices (limit or safety controls) or systems (alarm or
supervisory systems) intended to warn of, or protect
against, failure or malfunction of the T28 thermostat
must be incorporated into and maintained as part of
the control system.
Parts Included
•thermostat
•2 No. 6 screws
•2 fiber washers
Note: Plaster rings and switch box are not furnished.
Dimensions
Refer to Figure 1 and Figure 2 for detailed dimensions
of the T28 Fan Coil Thermostat.
Mounting
Location Considerations
Mount the thermostat about 4 to 5 ft. (1.2 to 1.5 m)
above the floor on an interior wall, where it can sense
the average room temperature. Do not mount the
thermostat where it may react to heat or cold from
water pipes, windows, doors, lamps, sunlight, or other
heat or cold sources.
On unit heater applications, place the thermostat
below and behind the heater in the path of air entering
the unit—not in the path of discharge air.
To mount the thermostat:
1. Install the switch box and plaster ring (when
required). See Figure 3.
2. Remove the cooling anticipator resistor to prevent
over-anticipation on 208/240 VAC installations.
Carefully clip the left-hand resistor leads with
diagonal cutters. See Figure 3.
3. Refer to Wiring section to make the necessary
connections.
4. Loosen the cover screw at the bottom of the cover,
swing the cover bottom out, and lift up to remove.
5. Fasten the thermostat to the switch box with the
two captive screws in the baseplate.
6. Carefully remove the contact protector (insulation
barrier). See Figure 3. Move the temperature
setting lever from Cool to Warm to be sure the
contact arm is free.
7. Reposition the cover, and tighten the cover screw.
8. Turn on the power supply.
9. Check the thermostat operation. Refer to the
Checkout section.
2 T28 Fan Coil Thermostat Installation Instructions
1.13
(29)
1.19
(30)
3.13
(80) 1.19
(30)
1.56
(40)
1.19
(30)
2.88
(73)
Two Mounting Holes for Number 6 Screws
3.28
(83)
5.19
(132)
Figure 1: T28 Without Fan Switch, in. (mm)
HIGH
OFF
MED
LOW
COOL
FA N
2.81
(71)
0.20
(5)
1.56
(40)
5.00
(127)
2.06
(52)
0.78
(20)
Two Mounting Holes for Number 6 Screws
5.19
(132)
1.19
(30)
2.67
(68)
3.08
(78)
3.28
(83)
Figure 2: T28 with Fan Switch, in. (mm)
Cover Insulation
Barrier
Mounting
Screws (2)
Cover
Screw
Fiber
Washer (2)
Two-gang
Switch Box
Junction
Box
or
Plaster
Ring
(Switch Box and
Plaster Ring Not Furnished)
Figure 3: Mounting the T28 to an Outlet Box, in. (mm)
T28 Fan Coil Thermostat Installation Instructions 3
Wiring
Make wiring connections using wire nuts or other
approved solderless connectors. See wiring diagrams
for proper connections.
!
WARNING: Risk of Electrical Shock.
Disconnect the electrical power supply before
making the wiring connections to avoid possible
electrical shock or damage to the equipment. On
multiple circuit units, more than one circuit may have
to be disconnected.
Cooling
to Fan
Blue
Tan
Ye ll ow
Red to
Cooling
Orange (hot) to L
1
Off LO
HI
h
Figure 4: T28BD Cooling Thermostat with
“Off-HI-MED-LO” Fan Switch
Heating-Cooling
to Fan
Blue
Tan
Ye ll ow
Orange
(hot) to L
1
Off LO
HI
h
Brown
to Heating
Red to
Cooling
Figure 5: T28CD Heating-Cooling Thermostat with
“Off-HI-MED-LO” Fan Switch
Sequenced Heating-Cooling
Note: Sequenced heating-cooling models have a
deadband allowing automatic changeover on
three-pipe or four-pipe systems.
No Fan Selector
HEATING - COOLING
Red to Cooling
Orange (hot) to L
1
Brown to Heating
h
Figure 6: T28DA Sequenced Heating-Cooling
Thermostat
Fan “OFF” Closes Cooling Valve
Orange
(hot) to L
1
Blue to Fan
Off
On h
Brown
to Heating
Red to
Cooling
Figure 7: T28DB Sequenced Heating-Cooling
Thermostat with “Off-On” Fan Switch
to Fan
Blue
Tan
Ye ll ow
Orange
(hot) to L
1
Off
On
LO
HI
h
Brown
to Heating
Red to
Cooling
Fan “OFF” Closes Heating
and Cooling Valves
Note:
Figure 8: T28DD Sequenced Heating-Cooling
Thermostat with “Off-HI-MED-LO” Fan Switch
Orange
(hot) to L
1
Off On
Brown
to Heating
Red to
Cooling
to Fan
Blue
Tan
Yellow
LO
HI
h
Figure 9: T28DG Sequenced Heating-Cooling
Thermostat with “Off-HI-MED-LO” Fan Switch
4 T28 Fan Coil Thermostat Installation Instructions
Table 1: Electrical Ratings (In Amperes)
Thermostat (Pilot Duty)
Cooling Heating Fan Switch
Volts, AC
Normal Inrush Normal Inrush Full Load Locked Rotor
120 0.32 1.0 0.12 0.36 5.8 34.8
208 0.18 0.57 0.07 0.21 3.3 19.8
240 0.16 0.50 0.06 0.18 2.9 17.4
Setup and Adjustments
Calibration
If the thermostat has a thermometer in the cover,
recalibrate the thermometer by following the steps
below:
1. Remove the thermostat cover.
2. Place an accurate test thermometer and the cover
side-by-side, allowing both the test thermometer
and the cover thermometer to reach a stable
temperature before adjusting.
3. Carefully turn the hex nut behind the insulator with
a thin wrench until the pointer corresponds to the
temperature indicated by the test thermometer.
Checkout
Before leaving the installation, observe at least three
complete operating cycles to ensure that all
components are functioning correctly. Follow the steps
below:
1. Move the lever toward Warm to raise the
temperature setting to check the heating cycle.
2. Move the lever toward Cool to lower the
temperature setting to check the cooling cycle.
The center of the scale is approximately 75°F
(24°C).
Repairs and Replacement
Field repairs must not be made. For a replacement
thermostat, contact the nearest Johnson Controls
representative.
T28 Fan Coil Thermostat Installation Instructions 5
Technical Data
Product T28 Fan Coil Thermostat
Thermostat 55 to 95°F (12 to 35°C)
Range Thermometer 55 to 85°F (12 to 30°C)
Heating 0.6F° (0.3C°)
Cooling 1F° (0.5C°) for typical 120 V Fan Coil Valve Loads
Nominal Operating
Differential Heating-Cooling Models with Automatic Changeover (T28D) have a 6F° (3.3C°)
Differential from Heating On to Cooling On
Adjustment Cool to Warm
Contact Action Snap-acting Bimetal-operated
Baseplate Cold Rolled Steel, Baked on Beige Paint
Material and Finish Cover Cold Rolled Steel, Baked on Ivory Paint
Thermometer Bimetal Type for Accuracy and Clarity, may be Field Adjusted
Without Fan Switch Standard Outlet Box with Captive Screws
Mounting With Fan Switch Mounts to a Two-Gang Switch Box
Wiring Connections Color Coded 18 AWG Wire Leads, 6 in. (152 mm) Long
Individual Pack - 1.0 lb (0.45 kg)
Without Fan Switch Overpack of 20 Units - 23.6 lb (10.7 kg)
Individual Pack - 1.3 lb (0.59 kg)
Shipping Weight
With Fan Switch Overpack of 20 units - 29.5 lb (13.4 kg)
Agency Listings UL Listed: File E6688, CCN XAPX
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
Controls Group
507 E. Michigan Street
P.O. Box 423 Printed in U.S.A.
Milwaukee, WI 53201 www.johnsoncontrols.com
Table des matières
Autres manuels Johnson Controls Thermostat
Johnson Controls
Johnson Controls TEC2045-4 Manuel utilisateur
Johnson Controls
Johnson Controls A19BAC Manuel utilisateur
Johnson Controls
Johnson Controls T701DFP-4 Manuel utilisateur
Johnson Controls
Johnson Controls T9580 Mode d'emploi
Johnson Controls
Johnson Controls GLAS Manuel utilisateur
Johnson Controls
Johnson Controls YORK DPC-1R Manuel
Johnson Controls
Johnson Controls T7000 Series Manuel utilisateur
Johnson Controls
Johnson Controls T9180 Mode d'emploi
Johnson Controls
Johnson Controls T5000-E Manuel utilisateur
Johnson Controls
Johnson Controls T9600 Manuel utilisateur
Johnson Controls
Johnson Controls FCP-NA-701-L Manuel utilisateur
Johnson Controls
Johnson Controls TEC20x6-4 Series Manuel utilisateur
Johnson Controls
Johnson Controls T-3102 Manuel d'utilisation et d'entretien
Johnson Controls
Johnson Controls T-4002 Manuel d'utilisation et d'entretien
Johnson Controls
Johnson Controls T25 Manuel utilisateur
Johnson Controls
Johnson Controls T-4002 Manuel utilisateur
Johnson Controls
Johnson Controls A19A Manuel utilisateur
Johnson Controls
Johnson Controls S1-THXU280W Guide de démarrage rapide
Johnson Controls
Johnson Controls T8200-TB20-9JS0/9JR0 series Manuel utilisateur
Johnson Controls
Johnson Controls T701DFN-1 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
