Jbc KN-A Manuel utilisateur

Table des matières

Autres manuels jbc pistolet à souder

Manuels pistolet à souder populaires d'autres marques

Bakon

Bakon 3200 Manuel utilisateur

Proxxon

Proxxon Gaslotset MGS Manuel utilisateur

HAKO

HAKO FX-8804 Manuel utilisateur

SATA

SATA 02002A Manuel utilisateur

Velleman

Velleman HRJA151 Manuel utilisateur

Weller

Weller WSM 1 Manuel utilisateur

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instructions de montage

ersa

ersa i-CON 1V Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-100 Manuel utilisateur

Weller

Weller WAD 101 Manuel utilisateur

Weller

Weller WXD 2 Manuel utilisateur

AlienTek

AlienTek T100 Manuel utilisateur

Atten

Atten ATETOOL AT-689A Manuel utilisateur

Surtek

Surtek 112554 Dimensions et guide d'installation

Parkside

Parkside PLBS 30 A1 Manuel utilisateur

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

multicomp pro

multicomp pro MP740893 Manuel utilisateur

INSTRUCTION MANUAL

Nitrogen Kit

Ref. KN-A

www.jbctools.com

2

www.jbctools.com

3

Packing List

The following items should be included:

Nitrogen Flow

Regulator ........................ 1 unit

Ref. MN-A

Nitrogen Handle ............ 1 unit

Ref. T245-NA

Stand ................................ 1 unit

Ref. DN-SE

Stand Cable ................... 1 unit

R ef. 0 01128 3

Nozzles .......... 2 units

Ref. B7243 (x1)

B7244 (x1)

Cartridge ......... 1 unit

Ref. C245903

Manual ............................. 1 unit

R ef. 0 013741

Module Cable ................ 1 unit

Ref. 0010207

Tip Cleaner ..... 1 unit

Ref. CL8499

Sponge ............ 1 unit

Ref. S0354

Nitrogen Kit

Ref. KN-A

INSTRUCTION MANUAL

www.jbctools.com

4

Features

The KN-A requires the GN-A generator or an available nitrogen supply at the operator´s bench.

Use Ø 6 ± 0.15 mm

polyurethane tubing

Nitrogen Flow Regulator

Ref. MN-A

Nitrogen Generator

Ref. GN-A

Control Unit

Ref. DI, DD, DDR, DM

Stand Cable

R ef. 0 01128 3

Module Cable

Ref. 0010207

Stand

Ref. DN-SE

Nitrogen Handle

Ref. T245-NA

Handle

N2tube

Compressed

Air Inlet

or from N2 net

N2pressure range

supply 3 to 6 bar

6 bar MAX

Nitrogen supply tube

Electric circuit

Main menu

Exit

1 Reset settings

2

Station settings

3

Tool settings

Station settings

1 Temp unit

Celsius

2

Maximum temp 400

0

C

3

Minimum temp 200

0

C

4

Nitrogenmode ON

www.jbctools.com

5

Once the Nitrogen Flow Regulator (MN-A) is connected to the Control Unit, enter the Station Settings

menu and enable the Nitrogen Mode.

The MN is an electrovalve controlled by the soldering station that allows you to solder using nitrogen.

It guarantees minimal gas consumption and prevents tip oxidation.

The nitrogen ﬂow is automatically activated when the soldering iron is lifted from the stand.

It stops when the tool is placed back and the tip temperature drops to the sleep mode.

Recommended N2ﬂow:

1-2 SLPM

N2 ﬂow control

Initial Set up

Operation

6

Clean periodically

Maintenance

Before carrying out maintenance or storage, always allow the equipment to cool.

- Use a damp cloth to clean the casing, the

stand and the tool. Alcohol can only be used

to clean the metal parts.

- Check periodically that the metal parts of

the tool/stand are clean so that the station

can check the tool status.

- Maintain tip surface clean and tinned prior to

storage in order to avoid tip oxidation. Rusty

and dirty surfaces reduce heat transfer to the

solder joint.

- Periodically check all cables and tube

connections.

- Replace any defective or damaged parts.

Use original JBC spare parts only.

- Repairs should only be performed by a

JBC authorized technical service.

www.jbctools.com

7

Safety

- Only nitrogen can be used with this unit.

- Do not use the unit for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded before

use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode. The

soldering tip, the stand and the metal part of the tool may still be hot even when the station is

turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight as well as persons with reduced

physical, sensory or mental capabilities or lacking experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

8

Exploded View

www.jbctools.com

9

10

Notes