Jbc TR245-A Manuel utilisateur

Table des matières

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel

Soldering Irons for Automation

Ref. TR245-A

INSTRUCTION MANUAL

www.jbctools.com

Packing List

The following items are included:

Manual ......................... 1 unit

Ref. 0020951

Insulator ..................... 1 unit

Ref. 0020440

Screws

DIN 912 M3X10............. 2 units

Ref. 0722900

Clamp .............................. 1 unit

Ref. 0018779

Screw

DIN 912 M4X16............. 1 unit

Ref. 0002984

Soldering Iron ........... 1 unit

Ref. TR245-A

Works with

R245 Cartidges

2

Assembly

Soldering Iron

for Automation*

Ref. TR245-A

Insulator Bushing

Ref. 0020440

Clamp

Ref. 0018779

Screw

Ref. 0002984

* If the Soldering Iron is ﬁxed in another way, it must be isolated from the ﬁxation.

The electrical Insulator Bushing

must be assembled for the tool to

work properly.

Do not remove the Insulator

Bushing.

Cooling fitting

For the correct operation

of this tool constant air flow is

needed. Always provide clean air.

Input preassure: 0,4 bar/ 5,8 psi.

www.jbctools.com

3

Screws

Ref. 0722900

Soldering Head

for Automation*

Ref. RBA-A

Assembly with RBA-A

* Not included, sold separately

The TR245 is connecta-

ble to the UCR245 using

the Tool Cable

Ref. 0021403

4

Inserting and removing Cartridges

The square recess of the Soldering Iron for

Automation must be matched with the square

shape of the Cartridge. Insert the Cartridge

until the two square shapes come to a limit

stop inside.

Insert the cartridge and press lightly until it

is placed in the Soldering Iron for Automation

(a). Use an allen key to tighten the Cartridge

in the Handle (b).

a

b

Cartridge range

Find the cartridge models that best suits your soldering needs in www.jbctools.com

Compatibility

Cartridge Range Control Unit

TR245 R245 UCR245

RBA, SFR, GSFR and CLMR are compatible with both R245 and R470 ranges.

For any hand operation make sure the power is off and both tool and cartridge are cold.

Before removing or inserting the cartridge, make sure air preassure is off.

www.jbctools.com

5

Dimensions

mm

(in)

TR245-A

6

Maintenance

- Before carrying out maintenance, always unplug the tool.

- Use a damp cloth to clean the tool. Alcohol can only be used to clean the metal parts.

- Periodically check that the metal parts of the tool are clean so the station can detect the tool status.

- Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat transfer to the solder joint.

- Replace any defective or damaged parts. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

It is imperative to follow safety guidelines to prevent electric shock,

injury, fire or explosion.

- Do not use the soldering iron for any purpose other than soldering or rework. Incorrect use may

cause fire.

- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.

- Do not leave the appliance unattended when it is on.

- Be sure that the power supply is disconnected before changing any spare part.

- Allow cartridges to cool down before changing them.

- Heat can cause inflamable products to ignite even when not visible.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when

working to avoid personal injury.

- Utmost care must be taken with liquid tin waste which can cause burns.

Safety

www.jbctools.com

7

This product should not be thrown in the garbage.

In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must

be collected and returned to an authorized recycling facility.

Warranty

JBC’s 2 year warranty covers this equipment against

all manufacturing defects, including the replacement

of defective parts and labour.

Warranty does not cover product wear or misuse.

In order for the warranty to be valid, equipment must

be returned, postage paid, to the dealer where it was

purchased.

www.jbctools.com

0024719-0420

Specifications

TR245-A

- Net Weight: 230 g (0.51 lb)

- Dimensions: 144.5 x 28 mm (5.69 x 1.10 in)

Clamp only

- Net Weight: 44 gr (0.10 lb)

- Dimensions: 55 x 33.5 x 10 mm (2.16x 13.18 x 0.39 in)

Complies with CE standards.

ESD protected.