Jbc DR560-A Manuel utilisateur

Español 10

Desoldering Iron

Ref. DR560-A

English 2

Page

INSTRUCTION MANUAL

www.jbctools.com

Packing List

Ref. DR560

Desoldering Iron

Tips ................................. 3 units

Ref. C560005* (x1)

Ref. C560013* (x1)

Ref. C560004* (x1)

Desoldering Iron .......... 1 unit

Ref. DR560-A

C560003 already inserted

The following items should be included:

Union flanges .......... 1 unidad

R ef. 0 0113 56

Tip cleaning set ............ 1 unit

Ref. 0965970*

Internal gasket .... 1 u.

Ref. 0019208*

It contains 2 gaskets

Filter box .............. 1 u.

Ref. 0780840

It contains 10 filters

Spanner ............. 1 unit

Ref. 0780550*

Spiral Filter .......... 1 u.

Ref. 0812330*

Long tip cleaning

set .................. 1 u.

Ref. 0965760*

Cleaning

stick .............. 1 u.

Ref. 0786640

Metal Solder

Collector .... 1 u.

Ref. 0812630*

Glass Solder

Collector ..... 1 u.

Ref. 0812620*

Manual ......... 1 u.

Ref. 0008867

*DR560-A Desoldering Iron accessories included in the Ref. 0010261

www.jbctools.com

Connection

Desoldering Iron

Ref. DR560-A

Tip

Ref. C560003

to desoldering module

to stand

Suction Filter

Ref. 0821830

Supplied with desoldering module

Desoldering process

Use a tip with a larger diameter than the pad to achieve maximum aspiration and thermal efficiency.

Place the tip with the

component terminal in

the hole.

After pressing the desoldering key there is a slight delay until the self-contained vacuum pump

stops. This makes sure that the vacuum circuit is completely empty. If any solder remains are left

on a terminal after desoldering it, resolder it with fresh solder and repeat the desoldering operation.

When the solder liquefies,

gently rotate the tip so

that the component

terminal can be lifted off.

Press the vacuum pump

button long enough to

remove the solder.

3. Aspirating1. Placing 2. Rotating

www.jbctools.com

A ø

B ø

C560-001 C560-002

C560-003

C560-004 C560-009

C560-014

Changing Tips

This operation should be done while the tip is hot and at a minimum temperature of 250°C, so that

any tin left inside is still molten.

1. Removing

Use the special spanner to unscrew the tip.

2. Inserting

Fit the new tip and tighten with the spanner

to make sure it is air tight.

Compatible Tips

The DR560 uses C560 tips.

Find the model that best suits your soldering needs in www.jbctools.com

Here are some C560 tips in real size:

250ºC minimum

C560-001 A=1,4 B=0,6 max. pin=0,4 mm

(A=0.05 B= 0.02 max. pin= 0.01 in)

C560-002 A=1,8 B=0,8 max. pin=0,6 mm

(A=0.07 B= 0.03 max. pin= 0.02 in)

C560-003 A=2,7 B=1 max. pin=0,8 mm

(A=0.1 B= 0.04 max. pin= 0.03 in)

C560-004 A=3,2 B=1,3 max. pin=1,1 mm

(A=0.12 B= 0.05 max. pin= 0.04 in)

C560-009 A=5 B=1,3 max. pin=1,1 mm

(A=0.19 B= 0.05 max. pin= 0.04 in)

C560-014 A=2,5 B=0,8 max. pin=0,6 mm

(A=0.09 B= 0.03 max. pin= 0.02 in)

1. Removing

Loosen the deposit lid (a),

remove the screw (b)

and withdraw the heating

element (c).

For this operation, turn off the station or disconnect the tool and wait until the tool temperature

drops to room temperature.

2. Placing

Insert the new Heating

Element (a), tighten the screw

(b) and then the lid (c).

Before placing, make sure

to insert the internal gasket

into the Glass Solder Collector.

Important

For a proper connection

it is essential to insert the

cartridge by lining it up to

the mark .

washer

Changing the heating element (Ref. DSV-DR)

Compatibility

The DSV-DR also works with

the previous version DR5600

Desoldering Iron (Ref. 5600010).

In this case, you must take out

the washer with a pliers.

www.jbctools.com

Glass Solder Collector Cleaning

1. Removing the lid

3. Inserting the glass solder collector

Check filter

Lid

Check

internal joint

2. Cleaning

Check the filter and replace it if it is dirty or

damaged.

Remove the coil and clean the inside of the glass

solder collector with the cleaning stick.

The lid must be unscrewed with the DR560 in a

vertical position.

The glass solder collector must be inserted

with coil filter in place, positioned between the

2 lines marked.

Then the whole unit must be closed by

screwing the lid.

Marks

Maintenance

Before carrying out maintenance or storage, always unplug the tool.

- Check periodically that the metal parts are clean to ensure it is detected when on the stand.

Always use a damp cloth or alcohol.

- Periodically check all cables and tubes connections.

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

The intake tube should be periodically cleaned by the largest rod.

Tip Care

Important

DO NOT press the vacuum pump button while tinning the desoldering tip, as the fumes given off

by the flux would quickly block the ducts and the air filter.

www.jbctools.com

It is imperative to follow safety guidelines to protect health and prevent electric

shock, injury, fire or explosions.

Safety

- Do not use the tool for any purpose other than soldering or rework. Incorrect use may cause fire.

- The mains cable must be plugged into approved bases. Make sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- The temperature of accessible surfaces may remain high after the unit is turned off.

Handle with care.

- Do not leave the appliance unattended when it is on.

- It is necessary to turn the station off before changing tips.

- Heat can cause inflamable products to ignite even when out of sight.

- Be careful with the remains of liquid tin. In contact with skin, it can cause burns.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- This appliance can be used by children over the age of eight as well as persons with reduced

physical, sensory or mental capabilities or lacking of experience provided that they have been

given adequate supervision or instruction concerning use of the appliance and understand the

hazards involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

- Weight: 413 gr (0.91 lb)

Complies with CE standards.

ESD protected.

Specifications

www.jbctools.com

Composición

Los siguientes artículos deben estar incluidos:

*Accesorios del desoldador DR560-A incluidos en la Ref. 0010261

Tips

Puntas .................... 3 unidades

Ref. C560005* (x1)

Ref. C560013* (x1)

Ref. C560004* (x1)

Desoldering Iron

Desoldador ................ 1 unidad

Ref. DR560-A

Punta C560003 incluida

Union flanges

Bridas de unión ......... 1 unidad

R ef. 0 0113 56

Tip cleaning set ...... 1 unidad

Juego de limpieza de puntas

Ref. 0965970*

Internal gasket

Junta interna ......... 1 u.

Ref. 0019208*

Contiene 2 juntas

Filter box

Caja de filtros ........ 1 u.

Ref. 0780840

Contiene 10 filtros

Spanner

Llave para puntas .. 1 u.

Ref. 0780550*

Spiral Filter

Filtro en espiral ..... 1 u.

Ref. 0812330*

Long tip

cleaning set

Juego de limpieza

de puntas ..... 1 u.

Ref. 0965760*

Cleaning stick

Bastoncillo de

limpieza del

depósito ....... 1 u.

Ref. 0786640

Metal Solder

Collector

Depósito metálico

de estaño ..... 1 u.

Ref. 0812630*

Glass Solder

Collector

Depósito de

estaño ........... 1 u.

Ref. 0812620*

Manual ......... 1 u.

Ref. 0008867

Ref. DR560

Desoldering Iron

www.jbctools.com

Autres manuels pour DR560-A

Table des matières

Langues :

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel

jbc DR560-A Manuel utilisateur

Manuels Outils électriques populaires d'autres marques