IWave FIP-2410 Manuel utilisateur

www.iwavecomms.com

1st

FIP-2410 User Manual

Contents

1. Package List .............................................................................................................................................................2nd

2. Precautions .............................................................................................................................................................2nd

3. Interface .................................................................................................................................................................. 4th

4. Installation ...............................................................................................................................................................4th

4.1. Make TX and RX and accessories ready. ......................................................................................................5th

4.2. Connection ................................................................................................................................................... 5th

4.3. Power on ...................................................................................................................................................... 5th

5. Software Configuration ........................................................................................................................................... 6th

5.1. Start The Software ....................................................................................................................................... 7th

5.2. RF Configuration ...........................................................................................................................................8th

5.3. RS1 Configuration ...................................................................................................................................... 11th

5.4. RS2 Configuration ...................................................................................................................................... 11th

5.5. IP New Network Configuration ..................................................................................................................12th

5.6. RF New NET Configuration .........................................................................................................................12th

5.6.4. Connect last IP ........................................................................................................................................ 13th

www.iwavecomms.com

2nd

1. Package List

2. Precautions

1) Be sure to use the parts provided by IWAVE.

2) Before powering on please make sure the antenna are in good connection and not install or

remove the antennas with power on.

3) Given that the carbon fiber body and metal load may have shielding effects on antenna signals,

they should not be installed between the antenna and ground terminal. Keep the antenna on

board free from winding or blocking by obstacles. The antenna end should be vertically

downward without bending to prevent shortening communication distance and failure

communication.

4) Antennas on board should be kept away from other radio antennas to avoid electromagnetic

noise and interference.

5) Do not disassemble or modify IWAVE FIP-2410. Any problem occur during installation, contact

IWAVE or IWAVE local branch office.

6) Keep appropriate distances between different electronic devices during installation to minimize

the electromagnetic interference.

www.iwavecomms.com

3rd

7) Before using, please make sure all cables are in good connection and all components can work

properly.

8) Check the surrounding environment to ensure there is no other 2.4GHz devices to cause

interference.

9) After starting the product, the self-test indicators of FIP-2410 will continuously blink for 30s and

then keep bright. Only after the video from the camera shown on the display, then you can

confirm that the device work properly now.

10) If you use the Futaba remote controller, the controller should be adjusted into the French

mode.

11) Adjust the Futaba controller into French mode as following steps:

[LINKAGE MENU]→FRQUENCY→ RTN b→ [AREA]→[FRANCE]

12) Before using, please check the power of RX and TX. If the receiver power off, transmitter on

board will lose connection.

13) Adjusting RX antenna inclination can improve the signal strength and image quality.

14) The camera should be fully charged to ensure normal video output.

15) FIP-2410 support video and duplex data communication. If the video stuck or stopped for more

than 10s, which means the radio signal is weakened or the radio channel is narrowed. In this

case, the aircraft need to fly back to short the distance between TX and RX. Otherwise the TX

will lose connection.

16) Please use good electromagnetic shielding accessories(such as HD displays, Network cables,

etc.)

Notes: Improper operation of FIP-2410 may cause personal injury or damage to properties. Please

pay high attention to operation safety.

www.iwavecomms.com

4th

3. Interface

Note: signal light meaning is as follows

1) After powering on, light 1,2,3 turn green, light 6 turns blue and light 8 turns red.

2) After 1 second, light 1, 2, 3 and 6 start to blink. Light 5 and 8 will keep constant light.

3) After a few seconds, the starting completed. Light 1(Green), 2(Green), 3(Green), 4(Red), 6(blue)

and 8(Red) will keep constant bright. By the way, when you use the the ETH1, 7 (Green) will

quickly blink.

1, 2, and 3 are signal strength indicators.

1Light 1 on: Signal Weak

2Light 1,2 on: Signal Normal

3Light 1,2,3 on: Signal Strong

(2) lights of 1, 2, and 3 are flashing repeatedly in sequence which means the device pairing is

unsuccessful, and Rx and Tx do not communicate.

4. Installation

www.iwavecomms.com

5th

4.1. Make TX and RX and accessories ready.

Besides the whole equipment we supply, you also need to make sure the IP

Camera, display and power source ready before installation.

4.2. Connection

Make the power cable, Ethernet cable, serial port cable and

antenna in good connection.

(the serial port cable is for data)

4.3. Power on

After checking all the connections are in good

condition, turn on the the video source, LCD display,

transmitter and receiver. The indicators will bright and

the whole system starts work.

Note:

Tx default IP: 192.168.55.1

Rx default IP: 192.168.55.2

Remark: In UAV application, please make the connection successfully and after the video show on ground station

smoothly then fly the UAV. About how to install the antenna on UAV please refer to the following figure.

www.iwavecomms.com

6th

5. Software Configuration

User’s Manual of TDD_COFDM V1.5

Note: As our devices are working pairs, so their parameters need be consistent, which mean when

www.iwavecomms.com

7th

one unit parameters are changed, the other unit parameters need to be change too. Or they will

lose connection.

The following show you two ways to do the parameters settings:

(1) Connect Tx or Rx with PC separately then change their parameters one by one.

(2) When the communication between Tx and Rx are working normally, you can change the

remote unit parameters through the local unit and then change the local unit parameters.

Note: If you find the devices cannot connect with PC, firstly wait for a moment for device finishing

its running process, then try again.

Secondly, check whether the distance between transmitter and receiver is too close, increase their

distance and try again.

If still failure, change another Ethernet cable.

5.1. Start The Software

1) Right-click the icon to choose“Run as administer”

www.iwavecomms.com

8th

2) Enter the IP address（Tx IP: 192.168.11.1 ; Rx IP: 192.168.11.2)，Next click Connect TDD button

If you want to Restart OFDM software, click Restart-TDD button.

Notice: You must restart the software after finishing modifying TX or RX parameters. Then type in another one’s

IP address, connect and modify its parameters. Please not change IP address directly in IP ADDRESS LOGIN.

5.2. RF Configuration

In this section, you can modify six parameters.

5.2.1. TX Rate(Default: QPSK FEC 1/2)

This setting determines the modulation type and the rate at which the data is wirelessly transferred.

For example:

www.iwavecomms.com

9th

Auto: The data will be transmitted at the highest possible rate in consideration of the receive signal

strength (RSSI)

If setting a fixed TX Rate, it is recommended to retain a fade

margin of at least 10dbm for optimum performance. For

example, for a link (8MHz channel) with a signal strength of

at least –75dBm, a TX rate of 16-QAM 3/4 FEC is

recommended. Note: Setting the highest rate with a poor

link will degrade the performance.

5.2.2. Channel Bandwidth(Default: 4Mhz)

The bandwidth channel can be selected from the list.

Note: Before choosing the bandwidth please refer to the

specifications to see the relationship and performance

between channel bandwidth , throughput and sensitivity.

Generally a larger channel has greater throughput at the

cost of sensitivity, while a smaller channel tends to be more

robust, but at the cost of throughput.

5.2.3. Channel-Frequency (Default:2479Mhz)

You can choose the frequency from 2402 to 2482Mhz

www.iwavecomms.com

10th

5.2.4. Wireless Distance(Default: 10km)

The Wireless Distance parameter allows a user to set the

expected distance that the wireless signal needs to travel.

The TDD-COFDM sets various internal timeouts to account

for this travel time. Longer distances will require a higher

setting, and shorter distances may perform better if the

setting is reduced.

5.2.5. RX TX Mode

TX Master - A Master provide a wireless data connection to

slave.

RX Slave- A Salve sustain one wireless connection to Master.

5.2.6. TX Power(Default: 29dbm)

This setting establishes the transmit power level which will

be presented to the antenna connector of the

TDD_COFDM. Unless required, the Tx Power should not be

set with maximum value, but rather for the minimum

value required to maintain an adequate system fade

margin.

Table des matières

Autres manuels iWave Matériel informatique

iWave

iWave iW-RainboW-G57M Manuel d'installation

iWave

iWave FIM-1440 Manuel utilisateur

iWave

iWave FIP-2420 Manuel utilisateur

iWave

iWave FNS-8408 Manuel utilisateur

iWave

iWave iW-RainboW-G30D Manuel utilisateur

iWave

iWave FIM-2450 Manuel utilisateur

iWave

iWave FD-6100 Manuel utilisateur

iWave

iWave iW-RainboW-G40D Manuel utilisateur

iWave

iWave FDM-615PTM Manuel utilisateur

iWave

iWave iW-RainboW-G25S Manuel utilisateur

iWave

iWave iW-RainboW-G37M Manuel d'installation

iWave

iWave iW-RainboW-G17D Manuel utilisateur

iWave

iWave iW-RainboW-G40M Manuel d'installation

iWave

iWave i.MX53 Manuel d'installation

iWave

iWave FIM-2405 Manuel utilisateur

iWave

iWave FNM-8416 Manuel utilisateur

iWave

iWave iW-RainboW-G47D Manuel utilisateur

iWave

iWave FPM-8416 Manuel utilisateur

iWave

iWave i.MX6 Qseven PMIC SOM Manuel d'installation

iWave

iWave FIP-2405 Manuel utilisateur

iWave

iWave iW-RainboW-G35D Manuel d'installation

iWave

iWave FDM-6600 Manuel utilisateur

iWave

iWave i.MX 8M Mini Manuel utilisateur

iWave

iWave iW-RainboW-G24M Arria10 SoC FPGA SOM Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

iWave FIP-2410 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques