Intersil ISL8011EVAL1Z Manuel utilisateur

User Guide 009

ISL8011xEVAL1Z Evaluation Board User Guide

Description

The ISL8011xEVAL1Z provides a simple platform to evaluate

performance of the ISL8011x family of split supply LDOs.

Jumpers are provided to easily set popular output voltages.

The ISL80111, ISL80112 and ISL80113 are single-output

LDOs specified for 1A, 2A, 3A of output current and are

optimized for less than 2.5V and less output voltage

conversions. The ISL8011x supports VIN voltages down to 1V,

provided a standard legacy 2.9V or 5.5V is applied on the

VBIAS pin. The output voltage is adjustable from 0.8V to 3.3V.

Specifications

This board has been configured and optimized for the following

operating conditions:

•V

IN range of 1V to 3.6V

•V

OUT adjustable from 0.8V to 3.3V

• Convenient power connection

• Popular output voltages can easily set by jumpers

Key Features

• Ultra low dropout: 75mV at 3A, (typ)

• Excellent VIN PSRR: 70dB at 1kHz (typ)

• ±1.6% guaranteed VOUT accuracy for -40ºC < TJ< +125ºC

• Very fast load transient response

References

ISL80111, ISL80112, ISL80113 Datasheet

Ordering Information

PART NUMBER DESCRIPTION

ISL80111EVAL1Z 1A, Split Supply LDO Evaluation Board

ISL80112EVAL1Z 2A, Split Supply LDO Evaluation Board

ISL80113EVAL1Z 3A, Split Supply LDO Evaluation Board

FIGURE 1. ISL80111EVAL1Z TOP SIDE FIGURE 2. ISL80111EVAL1Z BOTTOM SIDE

October 30, 2014

UG009.0

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.

All other trademarks mentioned are the property of their respective owners.

User Guide 009

2UG009.0

October 30, 2014

Submit Document Feedback

What’s Inside

The evaluation kit contains the following:

• The ISL80113EVAL1Z with the appropriate parts installed

•ISL80111, ISL80112, ISL80113 Datasheet

Test Steps

1. Select the desired output voltage by shorting one of the

jumpers from JP2 through JP5.

2. Connect both the BIAS and VIN supplies and the load. Enable

the IC using jumper JP6 (bottom position) or via a signal on

the center post, observe the output.

3. The shipped configuration is enabled and VOUT = 3.3V.

4. Scope shots taken from ISL8011xEVAL1Z boards.

Functional Description

The ISL8011xEVAL1Z provides a simple platform to evaluate

performance of the ISL8011x family of split supply LDOs.

Jumpers are provided to easily set popular output voltages.

The ISL80111, ISL80112 and ISL80113 are single-output LDOs

specified for 1A, 2A, 3A of output current and are optimized for

less than 2.5V and less output voltage conversions. The

ISL8011X supports VIN voltages down to 1V, provided a standard

legacy 2.9V or 5.5V is applied on the VBIAS pin. The output

voltage is adjustable from 0.8V to 3.3V.

An enable input, having a threshold <1V, allows the part to be

placed into a low quiescent current shutdown mode. A submicron

CMOS process is utilized for this product family to deliver

best-in-class analog performance and overall value for

applications in need of input voltage conversions to typically

below 2.5V. It also has the superior load transient regulation

unique to a NMOS power stage.

These LDOs consume significantly lower quiescent current as a

function of load compared to bipolar LDOs. This lower

consumption translates into higher efficiency and the ability to

consider packages with smaller footprints. The quiescent current

has been modestly compromised in design to enable leading

class fast load transient response and load regulation.

PCB Layout Guidelines

The following is an example of how to use vias to remove heat

from the IC.

Filling the thermal pad area with vias is recommended. A typical

via array is to fill the thermal pad footprint with vias spaced such

that they are center on center 3x the radius apart from each

other. Keep the vias small but not so small that their inside

diameter prevents solder from wicking through the holes during

reflow.

Connect all vias to the round plane. For efficient heat transfer, it

is important that the vias have low thermal resistance. Do not

use “thermal relief” patterns to connect the vias. It is important

to have a complete connection of the plated through-hole to each

plane.

FIGURE 3. PCB VIA PATTERN

User Guide 009

3UG009.0

October 30, 2014

Submit Document Feedback

Schematic

EVALUATION BOARD FOR:

GND

ISL80113

GND

ISL80111

ISL80112

1.0V

1.5V

1.8V

2.5V

3.3V

ISL80114

VADJ

VBIAS

VINVOUT

10UF

JP2

JP6

TP3

TP7

5.62K

TP2

TP6

JP5

TP1

TP5

100K

TP4

2.61K

1UF

10UF

JP3

4.02K

VOUT

VIN

GND

ADJ

VBIAS

ISL80113IRAJZ

5 6

JP1

JP4

2.05K

Bill of Materials

REFERENCE

DESIGNATOR VALUE DESCRIPTION MANUFACTURER

PART

NUMBER

U1 ISL80111, ISL80112 or ISL80113 as noted on

the evaluation board

Intersil ISL80111IRAJZ,

ISL80112IRAJZ,

ISL80113IRAJZ

C1, C3 10µF CAP, SMD, 0805, 50V, 10% Generic

C2 1µF CAP, SMD, 0603 Generic

R1 1kΩRES, SMD, 0603, 1% Generic

R2 2.05kΩRES, SMD, 0603, 1% Generic

R3 2.61kΩRES, SMD, 0603, 1% Generic

R4 4.02kΩRES, SMD, 0603, 1% Generic

R5 5.62kΩRES, SMD, 0603, 1% Generic

R6 1kΩRES, SMD, 0603, 1% Generic

R7 100kΩRES, SMD, 0603, 1% Generic

JP1, JP2, JP3,

JP4, JP5, JP6

Jumper Generic

TP1, TP2, TP3

TP4, TP5, TP6

Terminal Connector Generic

User Guide 009

4UG009.0

October 30, 2014

Submit Document Feedback

Board Layout

FIGURE 4. SILKSCREEN TOP FIGURE 5. TOP LAYER COMPONENT SIDE

FIGURE 6. BOTTOM LAYER SOLDER SIDE FIGURE 7. SILKSCREEN BOTTOM

User Guide 009

Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is

cautioned to verify that the Application Note or Technical Brief is current before proceeding.

For information regarding Intersil Corporation and its products, see www.intersil.com

UG009.0

October 30, 2014

Submit Document Feedback

Typical Performance Curves

FIGURE 8. DROPOUT vs VBIAS FIGURE 9. VIN PSRR vs LOAD CURRENT

FIGURE 10. VVIN PSRR vs LOAD CURRENT FIGURE 11. 1A LOAD TRANSIENT RESPONSE

FIGURE 12. 2A LOAD TRANSIENT RESPONSE FIGURE 13. 3A LOAD TRANSIENT RESPONSE

100

-40 25 125

TEMPERATURE (°C)

3A VBIAS = 3.3V

3A VBIAS = 5V

2A VBIAS = 5V

1A VBIAS = 3.3V

1A VBIAS = 5V

VIN DROPOUT VOLTAGE (mV)

2A VBIAS = 3.3V

100

100 1k 10k 100k 1M

PSRR (dB)

FREQUENCY (Hz)

IOUT = 2A

IOUT = 3A

IOUT = 0A

IOUT = 1A

BIAS = 5V

VOUT = 2.5V

VIN = 3.3V

COUT = 10µF

100

100 1k 10k 100k 1M

PSRR (dB)

FREQUENCY (Hz)

IOUT = 0A

IOUT = 2A

BIAS = 3.3V

VOUT = 1.0V

VIN = 1.5V

COUT = 10µF

IOUT = 3A

IOUT = 1A

VOUT (20mV/DIV)

IOUT = 1.1A

IOUT = 0.1A

TIME (20µs/DIV)

VOUT (20mV/DIV)

IOUT = 2.1A

IOUT = 0.1A

TIME (20µs/DIV)

VOUT (50mV/DIV)

IOUT = 3.1A

IOUT = 0.1A

TIME (20µs/DIV)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intersil Carte mère

Intersil

Intersil ISL54207EVAL1Z Manuel utilisateur

Intersil

Intersil JESD204B Manuel utilisateur

Intersil

Intersil ISL8026EVAL3Z Manuel utilisateur

Intersil

Intersil ISL72813SEHEV1Z Manuel utilisateur

Intersil

Intersil ISL70002SEHEVAL1Z Manuel utilisateur

Intersil

Intersil ISL54059EVAL1Z Manuel utilisateur

Intersil

Intersil ISL281X7MSOPEVAL1Z Manuel utilisateur

Intersil

Intersil ISL9120IIx-EVZ Manuel utilisateur

Intersil

Intersil ISL73033SLHEV1Z Manuel utilisateur

Intersil

Intersil ISL6228EVAL3Z Manuel utilisateur

Intersil

Intersil ISL71040MEV1Z Manuel utilisateur

Intersil

Intersil ISL8216MEVAL1Z Manuel utilisateur

Intersil

Intersil ISL97671A Manuel utilisateur

Intersil

Intersil ISL8215MEVAL1Z Manuel utilisateur

Intersil

Intersil ISL28133ISENSEV1Z Manuel utilisateur

Intersil

Intersil SL71010BM50EV1Z Manuel utilisateur

Intersil

Intersil ISL2827xINEVAL1Z Manuel utilisateur

Intersil

Intersil ISL6227EVAL1 Manuel

Intersil

Intersil ISL8018EVAL3Z Manuel utilisateur

Intersil

Intersil ISL28023EVAL1Z Manuel utilisateur

Intersil

Intersil ISL98001 Manuel du propriétaire

Intersil

Intersil ISL54302EVAL1Z Manuel utilisateur

Intersil

Intersil ISL70002SEHEVAL3Z Manuel utilisateur

Intersil

Intersil ISL6560 Instructions d'installation et d'utilisation

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur