Intersil ISL98001 Manuel du propriétaire
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 1/16 Ver. 1.1, 12/19/05
Installation and Operation of Intersil’s ISL98001
Analog Front End Evaluation System
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 2/16 Ver. 1.1, 12/19/05
Note
To simplify installation and prevent unnecessary Windows messages during installation, do
not connect the USB cable to the ISL98001 Evaluation Board until the software installation is
complete.
PC Requirements
Operating System: Tested under Windows XP (service pack 2) and Windows 2000. Windows 98 and
ME not currently supported.
Hardware Requirements: USB Port, CD-ROM drive for install files, minimum 10MB free hard disk
space.
Software Installation
Launch the “ISL98001 Installer.exe” file on the CD ROM and follow the instructions. The default
installation will add an “Intersil” directory to the “Start Menu/Programs” tree. That directory will contain
a shortcut to the ISL98001 executable and an uninstaller. The main program files will be installed in
the Program Files/ISL98001 directory. The USB driver file windrvr6.sys will be placed into
C:\WINDOWS\system32\drivers and ISL98001.inf will be installed under C:\WINDOWS\INF.
Press “Next” to continue.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 3/16 Ver. 1.1, 12/19/05
By default, the installer will put the evaluation software under c:\Program Files\ISL98001 directory.
To us a different directory, select the “Browse” button.
Press “Next” to continue.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 4/16 Ver. 1.1, 12/19/05
Press “Next” to create the Intersil folder in the Start Menu.
Press the “Install” button to copy all the necessary files onto the PC.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 5/16 Ver. 1.1, 12/19/05
Connecting the Evaluation Board
After installation of the ISL98001 software, re-boot the PC if requested. Apply power to the ISL98001
Evaluation Board with the provided 5V power supply. Connect the USB cable to the ISL98001
Evaluation Board. The Microsoft windows operating system will see the ISL98001 Evaluation Board
as a new device, and will try to load appropriate driver for it.
Windows XP may pop up this message:
If you see this box, select “Yes, now and every time I connect a device” and click on “Next”. If you
elect not to select “Yes, now and every time I connect a device”, you may see this requester
whenever the device is reconnected after being disconnected.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 6/16 Ver. 1.1, 12/19/05
The following screen will then appear:
Press Next (“Install the software automatically”).
The Hardware Wizard will try to locate and install the driver for the ISL98001:
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 7/16 Ver. 1.1, 12/19/05
Click Finish to complete the installation.
On XP systems, a pop-up message may display the status of the ISL98001 hardware.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 8/16 Ver. 1.1, 12/19/05
Hardware Setup
By default, the ISL98001 Evaluation board is configured for an input video resolution of
1280x1024@60Hz on the VGA1 connector. The quickest way to verify operation is this:
•Connect a monitor with a DVI input to the DVI output connector
•Connect a 1280x1024@60Hz RGB video source to VGA1
•Connect the 5V power supply to the power connector
At this point, the evaluation board’s FPGA will format the data from the ISL98001 and generate SXGA
video timing on the DVI output connector. The incoming SXGA image should appear on the DVI
monitor.
Additional video modes and AFE configuration options are available using the ISL98001 evaluation
software through the USB interface.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 9/16 Ver. 1.1, 12/19/05
Starting the Software
Launch the software (default location is Start/Programs/Intersil/ISL98001).
After the program has launched, you should see the following screen:
Click on the “Read All Registers” button in the lower left screen. All of the register values from the
ISL98001 on the evaluation board should appear as shown in the next image. If the register values
are not read correctly, proceed to the Troubleshooting section of this document.
Intersil Corporation
1001 Murphy Ranch Rd
Milpitas, CA 95035
Tel: 408-432-8888
http://www.intersil.com
©2005, Intersil Corp. Page 10/16 Ver. 1.1, 12/19/05
To change a register value, simply change the hexadecimal number in the appropriate box. To
change both digits of the 8 bit hex number, select both digits with the mouse (or double click inside
the text box) , then quickly type both digits of the desired value. If you type too
slowly (more than 1 second between the first and second digit), the first digit typed will become the
lower nibble, and the higher nibble will be 0. To only change one nibble using the keyboard, select
the high nibble or the low nibble and type the new hexadecimal
value.
You can also change the register values using the keyboard:
•Increment by 1: Up Arrow
•Decrement by 1: Down Arrow
•Increment by 16 (increment high nibble by 1): Page Up
•Decrement by 16 (decrement high nibble by 1): Page Up
Table des matières
Autres manuels Intersil Carte mère
Intersil
Intersil ISL8201M Manuel utilisateur
Intersil
Intersil ISL9214AEVAL1Z Instructions d'utilisation
Intersil
Intersil ISL41387EVAL1Z Manuel utilisateur
Intersil
Intersil ISL71010BM25EV1Z Manuel utilisateur
Intersil
Intersil JESD204B Manuel utilisateur
Intersil
Intersil HI5905EVAL2 Manuel utilisateur
Intersil
Intersil ISL32741EVAL1Z Manuel utilisateur
Intersil
Intersil ISL6227EVAL1 Manuel
Intersil
Intersil ISL54211EVAL1Z Manuel utilisateur
Intersil
Intersil HIP4086 Manuel utilisateur
Intersil
Intersil ISL8033DEMO1Z Manuel utilisateur
Intersil
Intersil ISL78205EVAL1Z Manuel
Intersil
Intersil ISL85009EVAL1Z Manuel utilisateur
Intersil
Intersil ISL1208 Instructions d'installation et d'utilisation
Intersil
Intersil ISL8215MEVAL1Z Manuel utilisateur
Intersil
Intersil QHx220 Manuel d'installation
Intersil
Intersil SL71010BM50EV1Z Manuel utilisateur
Intersil
Intersil ISL78268EVAL1Z Manuel utilisateur
Intersil
Intersil ISL70003ASEHEV2Z Manuel utilisateur
Intersil
Intersil ISL70040SEHEV2Z Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
