Intel SBT2 Manuel utilisateur

A guide for technically qualified persons

SBT2 Server Board

Quick Start Guide

Before You Begin.....................................................................2

Installation Notes

Installation Process Quick Reference ...........................................4

Remove the Access Cover............................................................5

Install the I/O Shield.....................................................................6

Rearrange the Standoffs................................................................7

Install the Server Board Bumpers.................................................8

Install the Retention Mechanisms.................................................9

Install the Server Board...............................................................10

Install the Auxiliary Cooling Fan Brackets..................................11

Installing Processors.................................................................... 12

Install the Processor Termination Card........................................14

Install the Processor Cooling Epac and Auxiliary Fans...............17

Memory.......................................................................................20

Connect Cables............................................................................ 21

Finish Setting up Your Chassis....................................................23

Common Problems......................................................................24

Jumpers .......................................................................................25

Server Board Components........................................................... 26

Back Panel Connectors................................................................27

Getting Help................................................................................28

Translations of this guide are available at:

Übersetzungen dieses Handbuchs sind erhältlich bei:

Versiones traducidas de esta guía se encuentran disponibles en:

Des traductions de ce guide sont disponibles à l'adresse:

Le versioni tradotte di questa Guida sono disponibili presso:

As traduções deste guia estão disponíveis em:

      

http://support.intel.com/support/motherboards/server/sbt2/manual.htm

copied, or reproduced in any form, or by any means without prior written consent of Intel.

Intel Corporation (Intel) makes no warranty of any kind with regard to this material, including,

but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Intel assumes no responsibility for any errors that may appear in this document.

Intel makes no commitment to update nor to keep current the information contained in this

document.

†Third-party brands and trademarks are the property of their respective owners.

Order Number: A28558-002

2 SBT2 Server Board Quick Start Guide

Before You Begin

Emissions Disclaimer

To ensure EMC compliance with your local regional rules and regulations, the final

configuration of your end system product may require additional EMC compliance testing.

For more information please contact your local Intel Representative.

See the

SBT2 Server Board Product Guide

for product Safety and EMC regulatory

compliance information. This is an FCC Class A device. Integration of it into a Class B

chassis does not result in a Class B device.

Safety Cautions

CAUTIONS

Pressing the power button does not turn off power to this board.

Disconnect the server board from its power source and from any

telecommunications links, networks, or modems before doing any of

the procedures described in this guide. Failure to do this can result in

personal injury or equipment damage. Some circuitry on the server

board may continue to operate even though front panel power button

is off.

Completely close the system to the original state in which you received

it. Failure to do this can result in personal injury, property and / or

equipment damage.

Read and adhere to all warnings, cautions, and notices in this guide

and the documentation supplied with the chassis, power supply, and

accessory modules. If the instructions for the chassis and power

supply are inconsistent with these instructions or the instructions for

accessory modules, contact the supplier to find out how you can

ensure that your computer meets safety and regulatory requirements.

Electrostatic discharge (ESD) can damage server board components.

Do the described procedures only at an ESD workstation. If no such

station is available, you can provide some ESD protection by wearing

an antistatic wrist strap and attaching it to a metal part of the computer

chassis.

SBT2 Server Board Quick Start Guide 3

Items Provided on the Bootable CD-ROM

SBT2 Server Board Product Guide

Intel

SC5000 Server Chassis Subassembly Product Guide

Software drivers and utilities

To view the product guides, boot to Windows†95/Windows NT†/

Windows 98/Windows 2000 and use Adobe†Acrobat†.

Safety and Regulatory Compliance

See the SBT2 Server Board Product Guide for product Safety and EMC

regulatory compliance information.

Intended uses: This product was evaluated for use in servers that will be

installed in offices, computer rooms, and similar locations. Other uses require

further evaluation.

EMC testing: Before computer integration, make sure that the chassis, power

supply, and other modules have passed EMC testing using a server board with a

microprocessor from the same family (or higher) and operating at the same (or

higher) speed as the microprocessor used on this server board.

Server board diagram label provided: Place the label inside the chassis in an

easy-to-see location, preferably oriented similarly to the server board.

I/O panel label provided: Place the label on the I/O shield. The cut outs are for

the top serial port and the parallel port.

Minimum Hardware Requirements

To avoid integration difficulties and possible board damage, your system must

contain the following minimum requirements. For a list of qualified memory

and chassis components see

http://support.intel.com/support/motherboards/server/SBT2/compat.htm

Processor

Minimum of one Intel®Pentium®III XeonTM processor and a processor

termination card. The SBT2 server board only supports processors with the

following product codes: BX80526KB866256, BX80526KB001256,

BX80526KB933256.

Memory

Minimum of 64 MB of 133 MHz, 3.3 V, PC/133 compliant registered SDRAM

on 168 pin gold DIMMs.

Power Supply

Minimum of 350 W with 0.8 A +5 V standby current (in order to support

Wake On LAN†(WOL)). You must provide standby current, or the board will

not boot.

4 SBT2 Server Board Quick Start Guide

Installation Notes

Before installing the SBT2 server board into your chassis, you must install the

processor retention mechanisms. The NIC LED, HD activity LED, and NMI

switch on the SC5000 front panel do not function with the SBT2 server board.

Installation Process Quick Reference

Step Where the

information is located

Remove the access cover This guide

Install the I/O shield This guide

Install the server board bumpers This guide

Rearrange the standoffs This guide

Install the processor retention mechanisms This guide

Install the server board This guide

Install the auxiliary cooling fan brackets This guide

Install the primary processor This guide

Install the processor termination card (or second

processor) This guide

Install the processor cooling epac and fans This guide

Install memory This guide

Connect cables to the server board This guide and the

SC5000 Product Guide

Finish setting up your chassis (start with “Install

the Diskette Drive”) SC5000 Product Guide

SBT2 Server Board Quick Start Guide 5

Remove the Access Cover

Facing the front of the chassis, the access cover is on the right side for pedestal-

mounted (tower) servers, and on the top for rack-mounted servers.

1 Loosen the captive thumbscrews that secure the access cover in place.

2 Slide the cover backward a short distance, until it stops.

3 Pull the entire cover outward, straight away from the chassis, to disengage

the rows of tabs from the notches in the top and bottom edges of the

chassis. Set the cover aside.

OM09083

6 SBT2 Server Board Quick Start Guide

Install the I/O Shield

✏NOTE

An ATX 2.03-compliant I/O shield is provided with the server board. The

shield is required by Electromagnetic Interference (EMI) regulations to

minimizes EMI. If the shield does not fit the chassis, obtain a properly

sized shield from the chassis supplier.

The shield fits the rectangular opening near the power supply in the back of

the chassis. The shield has cutouts that match the I/O ports.

1 Install the EMI gasket on the I/O shield. Peel the paper strip off of the

adhesive on the EMI gasket. Place the gasket on the board side of the I/O

shield (the side with the metal fingers). Make sure the holes in the EMI

gasket line up with the holes in the I/O shield.

2 Install the shield from inside the chassis. Orient the shield so that the

cutouts align with the corresponding I/O connectors on the server board.

Make sure the metal fingers are on the inside of the chassis.

3 Position one edge so that the dotted groove is outside the chassis wall, and

the lip of the shield rests on the inner chassis wall.

4 Hold the shield in place, and push it into the opening until it is seated.

Make sure the I/O shield snaps into place all the way around.

OM10628

5 Place the I/O label on the I/O shield. The cut outs on the label are for the

top serial port and the parallel port.

SBT2 Server Board Quick Start Guide 7

Rearrange the Standoffs

The standoffs in the chassis must be installed in screw holes

1,4,5,6,7,13,17,18,19,20,23,26. The hole numbers are stamped in the chassis

sheet metal. Make sure the two positioning standoffs are in holes 17 and 19.

Failure to properly rearrange the metal standoffs may cause the server board to

malfunction and may permanently damage the server board.

OM10429

171720

61319

18 23

8 SBT2 Server Board Quick Start Guide

Install the Server Board Bumpers

Peel the adhesive backing from three rubber bumpers; stick the bumpers to the

chassis wall.

OM10422

8.750

[222.25]

4.250

[107.95]

8.375

[212.72]

1.625

[41.27]

7.500

[190.50]

7.250

[184.15]

SBT2 Server Board Quick Start Guide 9

Install the Retention Mechanisms

The retention mechanism assembly consists of two plastic retention

mechanisms that go on the top of the server board, two steel stiffeners that go

underneath the board, and two plastic insulators that go between the steel

stiffeners and the server board.

Install the retention mechanism on the server board before installing the board

in the chassis.

1 Lay one steel stiffener (D) down on your work surface. Place one plastic

insulator (C) on top of it. Position the server board (B) over the stiffener

and insulator so the screw holes in the server board, insulator, and the

stiffener line up.

2 Place one plastic retention mechanism (A) on the top of the server board.

OM10414

3 Insert and tighten two screws to hold all the pieces in place.

4 Place the second stiffener and insulator on your work surface. Position the

server board over the stiffener and insulator so the screw holes line up.

5 Insert and tighten two screws to hold all the pieces in place.

6 Place the second plastic retention mechanism in place. Insert and tighten

four screws to hold it in place.

10 SBT2 Server Board Quick Start Guide

Install the Server Board

The screws for installing the server board are shipped with the chassis. You

may need to move cables out of the way to properly install your server board.

1 Remove the top piece of foam epac from the system fans.

2 Tilt the board into the chassis I/O connector end first. Position the board

so the screw holes line up with the standoffs. There are two positioning

standoffs (D) that extend into the holes on the server board. These two

standoffs will help you position the board correctly. Make sure the I/O

connectors stick out through the I/O shield. Look through the holes in the

I/O shield to make sure that the metal tabs on the I/O shield are on top of

the USB and NIC connectors, not inside.

3 Insert one screw through one of the mounting holes of the board and into a

threaded standoff. Do not tighten the screw until the next step.

4 Insert the remaining screws through the mounting holes and into the

threaded standoffs. Make sure the board is properly seated, then tighten all

the screws firmly, starting with the screws in the center of the board.

OM10427

Table des matières

Autres manuels Intel Carte mère

Intel

Intel DH57DD Manuel utilisateur

Intel

Intel DH67BL Manuel utilisateur

Intel

Intel Q77 Manuel utilisateur

Intel

Intel BLKDH67VR Guide de configuration

Intel

Intel DH61SA Manuel utilisateur

Intel

Intel DG965PZ Manuel utilisateur

Intel

Intel Desktop Board D845GLVA Manuel utilisateur

Intel

Intel D845GVSR - Desktop Board Motherboard Manuel utilisateur

Intel

Intel BLKDX58OG Guide de configuration

Intel

Intel Enpirion EM21 Series Manuel utilisateur

Intel

Intel BOXDX58SO Manuel utilisateur

Intel

Intel D945GCLF2 Manuel utilisateur

Intel

Intel DG41KR Manuel utilisateur

Intel

Intel BLKD915PBLL - LGA775 800FSB 4DDR2 Audio Lan 1394a SATA Raid ATX 4PCI 10Pack... Guide de configuration

Intel

Intel 32882 Manuel utilisateur

Intel

Intel BP4S33AT Manuel utilisateur

Intel

Intel BLKD945PSNLK Guide de configuration

Intel

Intel BLKD945GNTL - LGA775 1066 800FSB 4DDR2 A/V Lan SATA ATX 10Pack... Guide de configuration

Intel

Intel DX48BT2 - Desktop Board Extreme Series... Manuel utilisateur

Intel

Intel D2550DC2 Manuel utilisateur

Intel

Intel AN430TX - Motherboard - ATX Guide de configuration

Intel

Intel 1-N450 Manuel utilisateur

Intel

Intel DP67DE Manuel utilisateur

Intel

Intel DZ68AF Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur