Intel 5000 Series Manuel utilisateur

Intel®5000 Sequence Processor

Integration

Warning, Important Safety Instructions

System power on/off: The power button DOES NOT turn off the system AC power. To remove power

from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is

unplugged before you open the chassis, add, or remove any components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,

telephone, and communication cables. Turn off the server workstation and disconnect the power cord,

telecommunications systems, networks, and modems attached to the server workstation before opening

it. Otherwise, personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other

parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one

is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis

ground any unpainted metal surface on your server workstation when handling parts.

ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD.

Hold boards only by their edges. After removing a board from its protective wrapper or from the server

workstation , place the board component side up on a grounded, static free surface. Use a conductive

foam pad if available but not the board wrapper. Do not slide board over any surface.

Installing the Processor

Note:

• Do not touch the contacts on either the processor or the processor socket.

• Do not force the processor socket into place. When correctly aligned, the socket will easily drop

into place.

To install a processor, follow these instructions:

1. Observe safety and ESD precautions.

2. Turn off all peripheral devices connected to the server. Turn off the server.

3. Disconnect the AC power cord from the server.

4. Remove the chassis cover. See the documentation that came with your chassis for instructions

on removing the cover.

5. Locate the processor sockets (see Figure 1).

Figure 1. Example: Locating Processor Sockets.

Note: Consult Your Board Documentation for Proper Socket Location

6. Disconnect and remove any components necessary to access the processor sockets. See the

documentation that came with your chassis for instructions on removing chassis components.

7. Push down on the lever attached to the processor socket. While holding the lever down, pull it

towards the center of the board to disengage the lever from the hook. Fully open the lever. See

Figure 2.

Figure 2. Opening Processor Socket Lever

8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully

open the load plate. See Figure 3.

Figure 3. Opening Load Plate

9. If the protective cover is attached from the load plate, remove it and store it for future use. See

Figure 4.

Figure 4. Removing Protective Cover from Load Plate

10. Remove the processor from the box and remove the protective shipping cover.

11. Set the processor in the socket with the processor cutouts matching the processor socket

notches. See Figure 5.

Figure 5. Setting Processor in Place

12. Close the load plate.

13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of

the processor socket to engage it under the hook on the processor socket.

Installing the Heat Sink(s)

Note: The heat sink has thermal interface material (TIM) located on the bottom of it. Use

caution when handling the heat sink so you do not damage the TIM.

Each processor requires a heat sink. Depending on your chassis, you may need to use

either a active (Figure 6) or an passive heat sink (Figure 7). An active heat sink has a fan

attached to the top of it and a cable that needs to be connected to the server board.

AF000099

Figure 6. Active Heat Sink (Cable Not Shown)

Use the following steps to install a heat sink.

1. Set the heat sink over the processor, lining up the four captive screws with the four posts

surrounding the processor.

2. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 7.

Do not fully tighten one screw before loosely attaching the others.

3. In the same order, gradually and equally tighten each captive screw until each is firmly

tightened. Do not fully tighten one screw at a time.

Figure 7. Installing Heat Sink (Passive Heat Sink Shown)

4. Active heat sink only: Connect the heat sink cable to the server board. Reference you board

documentation for proper fan header location.

5. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.

See the documentation that came with your chassis for instructions on installing chassis

components.

6. Replace the chassis cover and reconnect the AC power cord. See the documentation that came

with your chassis for instructions on installing the cover.

Autres manuels pour 5000 Series

Table des matières

Autres manuels Intel Matériel informatique

Intel

Intel PXA255 Manuel utilisateur

Intel

Intel Pga478 - P4-2ghz 512kb 400mhz Fsb Manuel utilisateur

Intel

Intel E5420 - CPU XEON QUAD CORE 2.50GHZ FSB1333MHZ 12M LGA771 HALOGEN FREE... Manuel utilisateur

Intel

Intel EP80579 Manuel utilisateur

Intel

Intel DZ77GAL-70K Guide de configuration rapide

Intel

Intel Xeon Processor E5-1600 Manuel utilisateur

Intel

Intel X5550 - Quad Core Xeon Mode d’emploi

Intel

Intel 5400 Series Mode d’emploi

Intel

Intel D2550DC2 Manuel utilisateur

Intel

Intel LGA1155 SOCKET - THERMAL MECHANICAL S AND DESIGN GUIDELINES... Manuel utilisateur

Intel

Intel Xeon 5500 Series Mode d’emploi

Intel

Intel SASUC8I - RAID Controller Manuel d'installation

Intel

Intel i960 Jx Manuel utilisateur

Intel

Intel SRCU42L - RAID Controller Manuel utilisateur

Intel

Intel NUC Kit NUC1ATKPE Manuel utilisateur

Intel

Intel RMFBU4 Manuel utilisateur

Intel

Intel l2ICE Manuel utilisateur

Intel

Intel i86W Manuel utilisateur

Intel

Intel RS2BL080 - RAID Controller Manuel d'installation

Intel

Intel CORE 2 DUO MOBILE - THERMAL DESIGN GUIDE... Mode d’emploi

Intel

Intel I3-530 Manuel de l'opérateur

Intel

Intel E7500 Mode d’emploi

Intel

Intel E42249-003 Manuel du propriétaire

Intel

Intel E7500 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur

Jupiter

Jupiter RAM PACK Manuel utilisateur