INSIGHT VECTOR TR12 Manuel utilisateur

Insight Control TRI2 Installation Manual

www.insightcontrol.net.au

1300 665 831

Model: V-TRI2

Installation Manual

Insight Control TRI2 Installation Manual

READ AND UNDERSTAND THE INSTRUCTIONS CONTAINED HEREINAFTER BEFORE ATTEMPTING TO

UNPACK, ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THIS EQUIPMENT.

HAZARDOUS VOLTAGES ARE PRESENT THAT CAN CAUSE DEATH OR SEVERE PERSONAL INJURY. FOLLOW

PROPER INSTALLATION, OPERATION, AND MAINTENANCE PROCEDURES TO AVOID THESE VOLTAGES.

All possible contingencies that may arise during installation, operation, or maintenance, and all details and

variations of this equipment do not purport to be covered by these instructions. If further information is

required by the purchaser regarding an installation, application, or maintenance activity, please contact an

Insight Control representative or the installing contractor.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Document: V-TRI2 Installation Manual

Revision: R01

Date: 20212201

Phone: 1300 665 831

Email: [email protected]t.au

Website: www.insightcontrol.net.au

Address: D3 / 5 Grevillea Place

Brisbane Airport QLD 4008

 
Insight Control TRI2 Installation Manual 
 
About................................................................................................................................................................. 4 
VECTOR TRI2 Controller................................................................................................................................. 4 
Control Usage................................................................................................................................................ 4 
Touchscreen Touchpad ................................................................................................................................. 4 
System overview................................................................................................................................................ 5 
System components ...................................................................................................................................... 5 
Operating Instructions................................................................................................................................... 5 
Typical system installation................................................................................................................................. 6 
Technical notes.............................................................................................................................................. 6 
Motorised Dampers....................................................................................................................................... 6 
Component Positioning................................................................................................................................. 6 
Touchpad................................................................................................................................................... 6 
Room Sensor.............................................................................................................................................. 6 
Motorised Dampers................................................................................................................................... 6 
Commissioning .............................................................................................................................................. 6 
Connection Diagram.......................................................................................................................................... 7 
Terminals....................................................................................................................................................... 7 
Troubleshooting ................................................................................................................................................ 7 
Specifications..................................................................................................................................................... 8 
Electrical Requirements................................................................................................................................. 8 
Environmental Requirements........................................................................................................................ 8 
Positioning..................................................................................................................................................... 8 
 
 
 

Insight Control TRI2 Installation Manual

VECTOR TRI2 Controller

TRI2 operates independently of the air conditioning plant to provide temperature-based zoning control for

one zone. Features include:

• Integrated sensor or optional remote room sensor (not included)

Select the integrated sensor or the optional remote room sensor

• 24 VAC power supply

Offers substantial savings in installation costs compared to 240VAC systems

• Digital Display

Tell at a glance if the zone is open for cooling or heating.

• Quick & Easy Wiring

• BMS Integration

•Adjustable Minimum Ventilation setting

Restricts the damper from fully closing to maintain a minimum airflow.

Control Usage

TRI2 is a variable air volume zone controller suitable for use with any centralised conditioning source (e.g.

reverse cycle systems) Zoning kits comprise of one of each of the following components.

• TRI2 Controller (V-TRI2) - integrated sensor and supply air sensor

• Motorised Damper (MDB-XXX-IC) XXX = the size of the damper.

• Transformer (TFORM-24)

Touchscreen Touchpad

The TRI2 touchscreen controller compares the temperature of the air being supplied with the temperature

of the zone and modulates the damper in a direction that will benefit the zone. Zone motors connect to

and receive power from the touchpad via the Innocab cable system. Terminal connections are provided for

the 24VAC power supply, the supply air sensor, and optional external room sensor. TRI2 is equipped with

minimum ventilation calibration which adjusts a virtual stopper on the motor so that the motor is held

open a set percentage only when the zone is ON. Turning the zone OFF will override minimum ventilation

and fully close the motor.

Insight Control TRI2 Installation Manual

System components

1. TFORM-24 - 24volt Transformer

2. V-TRI2 –TRI2 Controller

3. MDB-XXX-IC –Belimo 24V 0-10V Motorised Damper barrel, where XXX is the size in millimetres

Operating Instructions

Press the button to turn the zone On and Off. Adjust the temperature by pressing for cooler &

for warmer. The setpoint range is from 20-25°C with a factory default of 22.5°C. Leave the controller in

“Auto”mode to work automatically off setpoint for heating or cooling based on return and supply air

temperature.

Insight Control TRI2 Installation Manual

Technical notes

A maximum number of 2 motors is allowed per output. In the event of power loss and restore to the

controller (i.e. blackout), the controller will drive the damper fully open before returning to the state (on or

off) and position it was in prior to the loss of power.

Motorised Dampers

Belimo 24V 0-10V Motorised damper connects to the touchpad. The TRI 2 version is suitable for use with

MDB-XXX-IC 4Nm motorised dampers only. The motorised dampers may be connected in parallel with a

maximum of two motors per zone output.

Component Positioning

Touchpad

The Touchpad should be mounted in a central position within the air-conditioned space. Designed to be

flush mounted to a cavity wall, the touchpad can be surface mounted using a 15mm mounting block if

necessary. If using the integrated sensor see also - positioning the room sensor. Due to the microprocessor-

based design, consideration must be given to sources of EMI (Electro Magnetic Interference) when

positioning the touchpad. The minimum recommended distance from the touchpad to any 240VAC cabling

is 300mm.

Room Sensor

The integrated room sensor should be mounted approximately 1.5 meters from floor level in the return air

path. Most importantly, the room/return air sensor should always be protected from direct sources of heat

such as direct sunlight and office equipment. The integrated room sensor may be replaced with an Insight

Control room sensor (C-RS-10K-TL) if required. The supply air sensor should be mounted inside the supply

air duct upstream from the damper. There should be no electric duct heaters in this supply duct branch.

Motorised Dampers

The Motorised Dampers may be mounted at the take-off point of the rigid duct, or inline in the flexible

duct. Mechanical Stops MUST NOT be used on the Motorised Barrel Damper.

Commissioning

Check that all wiring has been terminated as per wiring instruction on the connection diagram page. Check

Motor rotation set to turn clock wise on normal operation, flick switch on top of belimo as required.

Setpoint should be set to optimal temperature setting for zone being controlled for correct operation of the

system.

Insight Control TRI2 Installation Manual

Terminals

The following table lists some commonly reported fault conditions and suggested corrective action. Further

assistance may be obtained from Insight Control support on 1300 665 831 if needed.

Symptom

Suggested remedial action

Motor drives the wrong way

Check Actuator wiring.

Motor drives one way only

Check cable ends to ensure all connections are terminated

properly. Check cable for broken wire.

Intermittent erratic controller

behaviour

Ensure the touchpad is the minimum recommended distance

from any EMI source. Relocate if necessary.

10K NTC

Supply Air

Sensor

V+ 24 VAC Supply

GND 24 VAC Neutral

1 Wire 1 from Actuator

2 Wire 2 from Actuator

3 Wire 3 from Actuator

8 10K Sensor Wire 1

GND 10K Sensor Wire 2

Vector TRI2

TFORM-24

Belimo Actuator

24V 0-10V

1 2 3

Insight Control TRI2 Installation Manual

Electrical Requirements

Power input to ZONE-IT

24 VAC ± 10%

Line frequency

50 Hz

Environmental Requirements

Operating temperature

0°C to 50°C

Altitude

0 to 2000m

Operating relative humidity

10% to 80%

Positioning

Avoid static electricity hazards

Avoid electromagnetic radiation sources

Avoid dust contamination

Avoid highly corrosive environments

Phone: 1300 665 831

Email: sales@insightcontrol.net.au

Website: www.insightcontrol.net.au

Address: D3 / 5 Grevillea Place

Brisbane Airport QLD 4008

Ce manuel convient aux modèles suivants

Table des matières

Manuels écran tactile populaires d'autres marques

Elecro Engineering

Elecro Engineering Poolsmart Plus Instructions d'installation

Johnson Controls

Johnson Controls IQ4 HUB Manuel utilisateur

Elo TouchSystems

Elo TouchSystems ET2270L Manuel utilisateur

Elo TouchSystems

Elo TouchSystems ET1002L Manuel utilisateur

Elo TouchSystems

Elo TouchSystems 3201L Manuel utilisateur

Duratec

Duratec S15 Manuel utilisateur

Crestron

Crestron TPMC-3SM Manuel utilisateur

Racelogic

Racelogic MFD Touch Manuel utilisateur

J2 580 Guide de l'utilisateur

HAI

HAI OmniTouch 10p Manuel utilisateur

panel

panel PC PSR108-FM Series Manuel utilisateur

Tipro

Tipro FREE+ Manuel utilisateur

Systemline

Systemline Commander Manuel utilisateur

Interactive Technologies

Interactive Technologies Insite Manuel utilisateur

GVision

GVision Legacy Manuel utilisateur

BeiJer

BeiJer T21C-C24 Manuel utilisateur

Advantech

Advantech ITM-5117 Series Manuel utilisateur

Edge

Edge CS Manuel utilisateur