InFocus Work Big IN32 Mode d’emploi

33

Replacing the projection lamp

The lamp hour timer in the Service Info menu counts the number of hours

the lamp has been in use. Twenty hours before the specified end of the

lamp’s life, the message “Replace lamp” briefly appears on the screen at

each startup. When the expected lamp life has been reached, the Lamp indi-

cator icon lights red (page 12).

NOTE: You can order new lamp housings from www.infocus.com (in select

areas), your retailer or your dealer. Use only a replacement lamp with the

same type and rating as the original lamp.

1Turn off the projector and unplug the power cable.

2Wait 60 minutes to allow the projector to cool thoroughly.

3Turn the projector upside down and remove the lamp door by placing a

flat-blade screwdriver into the space between the lamp door and the

projector and gently prying the door off.

4Loosen the captive screw on the lamp module.

WARNINGS:

• To avoid burns, allow the projector to cool for at least 60 minutes before

you replace the lamp.

• Unplug the power cord before replacing the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

• Do not touch the glass lamp screen. Fingerprints can obscure projection

sharpness.

Service Info menu

turn off and unplug

the projector

wait 60 minutes

pry the lamp door off

loosen the screw on lamp module

34

• Be extremely careful when removing the lamp housing. In the unlikely

event that the lamp ruptures, small glass fragments may be generated.

The lamp module is designed to contain most of these fragments, but

use caution when removing it. Before replacing a ruptured lamp, clean

the lamp compartment and dispose of cleaning materials. Wash hands

after lamp replacement. This product has a lamp which contains a very

small amount of mercury. Dispose of it as required by local, state or fed-

eral ordinances and regulations. For more information see

www.eiae.org.

5Detach the lamp connector from the projector by gently pulling the con-

nector until it is disconnected from the projector.

6Carefully remove the lamp module by grasping and lifting the metal

bail wire. Dispose of the lamp in an environmentally proper manner.

7Install the new lamp module, making sure that it is properly seated. Be

careful not to touch the interior components of the projector.

8Snap the bail wire back into its flat position against the lamp module.

9Re-attach the lamp connector to the projector. Make sure the connector is

fully inserted.

10 Tighten the screw on the lamp module.

11 Replace the lamp door.

12 Plug in the power cable then press the Power button to turn the projec-

tor back on, then reset the lamp hour timer.

Resetting the lamp timer

To reset the lamp timer, navigate to the Settings>Service menu and select

Reset Lamp Hours.

disconnect lamp connector

remove module using bail wire

reset lamp time in Service menu

Autres manuels pour Work Big IN32

4

Ce manuel convient aux modèles suivants

3

Table des matières

Autres manuels InFocus Projecteur

InFocus

InFocus IN226ST Manuel utilisateur

InFocus

InFocus in3138hd Manuel utilisateur

InFocus

InFocus LP790 Manuel utilisateur

InFocus

InFocus in114ST Guide d'installation

InFocus

InFocus Play Big IN82 Manuel utilisateur

InFocus

InFocus LP 420 Manuel utilisateur

InFocus

InFocus LP280 Manuel utilisateur

InFocus

InFocus in2124 Manuel utilisateur

InFocus

InFocus LP 425 LiteMount Manuel utilisateur

InFocus

InFocus IN3124 Manuel utilisateur

InFocus

InFocus Play Big IN83 Manuel utilisateur

InFocus

InFocus IN5132 Manuel utilisateur

InFocus

InFocus IN2124a Manuel utilisateur

InFocus

InFocus LP 820 Guide de configuration rapide

InFocus

InFocus Learn Big IN5102 Manuel utilisateur

InFocus

InFocus LP 725 Manuel utilisateur

InFocus

InFocus X1 Manuel utilisateur

InFocus

InFocus W3902 Manuel utilisateur

InFocus

InFocus LP330 Manuel utilisateur

InFocus

InFocus LP70+ Manuel utilisateur

InFocus

InFocus LP280 Manuel utilisateur

InFocus

InFocus LP720 Manuel utilisateur

InFocus

InFocus SP-LAMP-100 Mode d’emploi

InFocus

InFocus LASER PROJECTOR LP 540 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur