Impex COMPETITOR CB-430 Manuel utilisateur

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

Model

CB-430

Retain This

Manual for

Reference

07-03-03

OWNER'S

MANUAL

COMPETITOR BENCH

CB-430

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com

[email protected]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................…. 1

IMPORTANT SAFETY NOTICES..................................................................…. 2

HARDWARE IDENTIFIER.....…....................................................................…. 3

ASSEMBLY INSTRUCTIONS........................................................................…. 4

EXPLODED DIAGRAM………………………………………………………………. 10

PARTS LIST...............................................................................................……. 11

WARRANTY.................................................................................................…. 12

ORDERING PARTS.......................................................................................… 12

BEFORE YOU BEGIN

Thank you for selecting the COMPETITOR CB-430 Bench by IMPEX

FITNESS PRODUCTS. For your safety and benefit, read this manual

carefully before using the machine. As a manufacturer, we are committed

to provide you complete customer satisfaction. If you have any questions, or

find there are missing or damaged parts, we guarantee you complete

satisfaction through direct assistance from our factory. To avoid

unnecessary delays, please call our TOLL-FREE customer service number.

Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[email protected]m

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal

symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water

or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or

other clothing that could become caught in the machine. Running or aerobic shoes are

also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in

attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm

up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE

OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES

NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE

SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

HARDWARE IDENTIFIER

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen

Wrenches

NOTE: It is strongly recommended two or more people assembling this machine to

avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3

1/8” Carriage Bolts (#54), one 4 ¾” x 1 5/8” Bracket (#26), two ∅¾” Washers (#64),

and two M10 Aircraft Nuts (#63).

B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6). Attach the Main

Frame (#4) to the Lat Bar Base. Secure them together with two M10 x 3 3/8” Carriage

Bolts (#52), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63). Diagram 1

STEP 2 (See Diagram 2)

A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar

Frame into the opening on the Lat Bar Base (#6).

B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame,

Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 ¾” Carriage Bolts

(#56), one 1 5/8” x 2” Bracket (#38), one 6 ¾” x 2” Bracket (#39), three ∅¾” Washers

(#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet.

C.)Place the Backrest Adjustment Bar (#10) onto the holders on the Cross Brace.

D.)Attach two Spring Clips (#34) onto the weight posts on the Sliding Weight Post (#11).

E.) Insert one M10 x 2 3/8” Allen Bolt (#67) through the hole on the Lat Bar Frame. Secure

it with two Ø ¾” Washers (#64) and one M10 Aircraft Nut (#63).

DIAGRAM 2

STEP 3 (See Diagram 3)

A.) Attach the bottom of Right Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right

Upright Beam to the Cross Brace (#7).

B.) Secure the Right Upright Beam to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts

(#54), ∅¾” Washers (#64), and M10 Aircraft Nuts (#63).

C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts

(#56), one 4 ¾” x 2” Bracket (#27), two ∅¾” Washers (#64), and two M10 Aircraft Nuts

(#63).

D.) Repeat Steps A, B, and C above to install the Left Upright Beam (#2).

E.) Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam.

DIAGRAM 3

STEP 4 (See Diagram 4)

A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball

stopper of the Cable is underneath the Frame.

B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8”

Pulley Bushings (#43), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

C.)Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure

it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two ∅¾” Washers

(#64), and one M10 Aircraft Nut (#63).

D.)Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10

x 1 3/8” Allen Bolt (#53), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

E.) Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable

with another C-clip.

STEP 5 (See Diagram 5)

A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2

½” Allen Bolt (#57), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15).

Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1

3/8” Hex Bolts (#58) and ∅½” Washers (#66).

C.)Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts

(#60) and ∅½” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support

to lock the Seat and Backrest Board in position. Remove the Pin when folding the Backrest

Board forward to allow access to the “Walk-in Squat”.

D.)Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex

Bolts (#61) and ∅5/8” Washers (#65).

E.) Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock

Knob (#33). DIAGRAM 5

STEP 6 (See Diagram 6)

A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt

(#59), two ∅¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert

two Foam Tubes halfway through the holes on the Leg Developer.

C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends.

D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a L-

shaped Pin (#40). Remove the Pin and the Curl Bar when doing Leg Developer

exercises.

E.) Attach a Spring Clip (#34) to the weight post on the Leg Developer.

DIAGRAM 6

Table des matières

Autres manuels Impex Salle de sport à domicile

Impex

Impex MARCY MWB 716 Manuel utilisateur

Impex

Impex CB-204 Manuel utilisateur

Impex

Impex COMPETITOR CB-349 Manuel utilisateur

Impex

Impex MARCY MWM-990 Manuel utilisateur

Impex

Impex NS-1000 Manuel utilisateur

Impex

Impex MD-867 Manuel utilisateur

Impex

Impex Apex TC-3500 Manuel utilisateur

Impex

Impex MD-867W Manuel utilisateur

Impex

Impex MARCY MWB-70500 Manuel utilisateur

Impex

Impex MARCY MD-859P Manuel utilisateur

Impex

Impex MWM 2001 Manuel utilisateur

Impex

Impex MARCY SB-261W Manuel utilisateur

Impex

Impex MARCY DIAMOND ELITE SM-1050 Manuel utilisateur

Impex

Impex CB 420 Manuel utilisateur

Impex

Impex MACH V Manuel utilisateur

Impex

Impex Marcy Platinum MP-PWR10.0 Manuel utilisateur

Impex

Impex APEX TC-3502 Manuel utilisateur

Impex

Impex MARCY MWM-1001 Manuel utilisateur

Impex

Impex MARCY CR 5 Manuel utilisateur

Impex

Impex PWR SURGE Manuel utilisateur

Impex

Impex POWERHOUSE SB-210 Manuel utilisateur

Impex

Impex MARCY SM-4231 Manuel utilisateur

Impex

Impex MARCY MCB-849 Manuel utilisateur

Impex

Impex MARCY PLATINUM MP-2500 Manuel utilisateur

Manuels Salle de sport à domicile populaires d'autres marques

Horizon Fitness

Horizon Fitness OXFORD 6 Manuel utilisateur

Energetics

Energetics Multi Trainer 5.1 Manuel utilisateur

Matrix

Matrix MG-PL Series Manuel utilisateur

Reebok

Reebok Tbr2i Manuel d'utilisation et d'entretien

Weider

Weider 8300 Hard Drive Manuel utilisateur

Pure Fitness

Pure Fitness 8526HE Manuel utilisateur

Weider

Weider 8700 I Guide de démarrage rapide

Bowflex

Bowflex Sport 001-6961 Manuel utilisateur

NordicTrack

NordicTrack E8200 Competition Bench Guide de démarrage rapide

Weider

Weider WEMC10161 Manuel utilisateur

Body Solid

Body Solid GHYP-345 Manuel utilisateur

Evo

Evo TAHOE 5105 Manuel utilisateur

cardiobull

cardiobull RA17 Manuel utilisateur

ParaBody

ParaBody 40 Manuel utilisateur

JLL

JLL Ventus Pro Air Power Manuel utilisateur

Trojan

Trojan Colorado 370 Manuel utilisateur

Octane Fitness

Octane Fitness xRide xR650 Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur