Ikelite 5510.45 Manuel utilisateur

Thank you for your purchase of Ikelite equipment. Please read this

instruction manual completely before attempting to operate or dive

with this product. Please refer to the back page of this manual to

8 in. Dome with Shade 5510.45

Instructio n Manual

#$-'0(0/4'/43

Important Notice ............................................P. 3

Port Bodies ....................................................P. 4

Install Port Bodies on the 8” Dome ................P. 5

Install Port on a Housing................................P. 6

Remove Port from a Housing............................P. 8

Port Shade Alignment........................................P. 8

Port Lock Information ....................................P. 9

Port Shade Installation/Removal....................P. 10

Port Seal - Inside View ..................................P. 12

ptional Replacement -rings ......................P. 13

Maintenance ..................................................P. 14

Ikelite Limited Warranty..................................P. 15

Returning Products for Service ......................P. 16

.1024#/404+%'

Port bodies are engraved with a Maximum Depth Rating;

“RATED 200 FT (60m).” They are engraved on the flat flange

that rests against the front of the camera housing; see

illustration.

lder standard and extended port bodies that are N T

engraved have a Maximum Depth Rating of 150 ft. (45m). The

unmarked standard or extended port bodies can be returned to

Ikelite for a no charge replacement with the newer 200 ft. (60m)

rated bodies. 0/04 send the dome when returning the port

body.

All super wide bodies are “RATED 200 FT (60m)” whether

they are engraved or not. 0/04 return super wide bodies

for exchange.

Maximum Depth

Rating engraved

on flange

0240&+'3

For information on the full selection of 8 in. dome port bodies,

please visit 777+,'-+4'%0..

Dome with Shade

5510.45

Extended Body

5510.24

Standard Body

5510.16

Super Wide Body

5510.11

Camera Housing / Port pening

Dome

Shade

Base Plate

Cut-outs

/34#--0240&+'30/4*':0.'

Install bodies by

screwing them into

the base plate of the

5510.45 dome port.

The seal between the

body and the dome

base plate is a side to

side seal and requires

the o-ring to be lightly

lubricated for easy

installation. Remove

the body/base plate

o-ring, put a small

amount of lubricant

on your fingers and

pull the o-ring through

your fingers to lightly lubricate it. Do not stretch the o-ring.

Check that the o-ring groove in the body where the o-ring fits

and the sealing surface on

the port base plate are clean.

Replace the o-ring onto the

body and then screw the

body into the base plate of

the dome port. Screw the

body in until it stops. The

front edge of the body should

be flush or slightly above the

inside face of the dome base

plate as shown

in the cross-section.

Dome

Front edge of Body

Face of Base Plate

%20333'%4+0/

Port Body

Housing/Port o-ring

Body/Base Plate o-ring

-rings

Port Body

/34#--0240/#053+/)

There are four port locks on the front of the housing. Each port

lock has a release button. Lift

the release button and slide

each port lock away from the

port opening. In the unlocked

position, the release button

will remain in the “up”

unlocked position as shown.

Whe usi g the 5510.11

superwide port body, the port locks must be i the “dow ” locked

positio . Refer to your 5510.11 i structio ma ual for this

i stallatio .

Port Lock

Release

Button

Lift Release

Button to

Unlock

Pull Back to

Disengage

Port

“Up” Unlocked Position

“Down” Locked Position

IKELITE

Port

Locks

0240%,

/34#--0240/#053+/)%0/4

To prepare the port for installation, remove the port o-ring and

lightly lubricate it. The port seal is a side-to-side seal and

requires the o-ring to be lightly lubricated for easy installation.

Put a small amount of lubricant on your fingers and pull the

o-ring through your fingers to lightly lubricate it. Do not stretch

the o-ring. Check that the lip of the port where the o-ring fits and

the sealing surface on the housing are clean.

Place the port, with o-ring, into the housing port opening. Press

down on the port firmly and evenly until you feel the port slide

into place. Continue to push down on the port and push each

port lock forward until the lock fully engages. It may help to

slightly rotate the port as you push in on the port lock. Visually

inspect the port lock and confirm that the port lock release

button is seated flush against the port lock body - Page 6. Do

not rely only on an audible "click" to indicate that the lock is

engaged.

Check around the perimeter of the port seal to see that the

o-ring is properly sealed and not extruded #)'+).

Cut-out Cut-out

'.06'024 (20.#053+/)

'8%'147+4*51'27+&'0240&9

To remove the port, lift up on each Port Lock Release Button

and slide the port lock away from the port. Lift port from

housing.

The o-ring may be left in the port hole of the housing when the

dome port is removed. Replace the o-ring in the proper position

on the port body before reassembling the housing and dome

port.

To remove a port with a 5510.11 superwide port body, refer to

the 5510.11 instruction manual.

024*#&'-+)/.'/4

Rotate the port so the 4 cut-outs in the shade are at the 2, 4, 8

and 10 o’clock positions in relation to the camera lens view.

When using the 5510.11 superwide port body, refer to your

5510.11 instruction manual for proper shade alignment.

04'The Low Profile Port Locks work with all Ikelite port bodies.

nce they have been installed, there is no reason to replace

them.

0240%,/(02.#4+0/

7*'/53+/)4*'51'27+&'0240&9

When using the 5510.11 superwide port body, unmodified

(2-port lock housings) produced prior to March 2006 require the

installation of low-profile port locks (now standard on all DSLR

housings). These may be purchased through your local Ikelite

dealer or directly from Ikelite. Request two 9072.24 port locks

when ordering.

All Ikelite digital SLR housings produced since March 2006

(serial number 15798 and above) are fully compatible with all

port bodies including the 5510.11 superwide port body and

require no modification.

To visually compare older port locks, measure 7/16" from the

bottom to the top of the retaining screw slot. Low-profile port

locks measure 5/16". Refer to the figures below.

Ikelite film SLR housings are not compatible with the 5510.11

superwide port body.

Standard Port Lock

Port Lock

Retaining Screw

Low-Profile Lock

Measure Measure

024*#&'/34#--#4+0/'.06#-

- Reference illustrations on page 11.

1. Place the port shade on a flat surface with the cut-out

section face down +)1#)'.

2. Loosen the four set screws with the Allen wrench. The set

screws do not have to be removed, unscrew them until the

face of the set screw does not protrude beyond the inside

face of the dome shade.

3. Carefully place the port inside the shade with the

dome face down +)1#)'. The dome port should

rest on the two inner ledges of the shade +)1#)'.

4. Hold the port in place and tighten the four set screws

with the allen wrench provided. Tighten the set screws

until the face of each set screw is even with the face of

the port shade +)1#)'.

Autres manuels pour 5510.45

Table des matières

Autres manuels Ikelite Accessoires pour appareils photo

Ikelite

Ikelite 6242.12 Canon S120 ULTRAcompact Manuel du propriétaire

Ikelite

Ikelite 6961.85 Manuel utilisateur

Ikelite

Ikelite 6282.68 Manuel du propriétaire

Ikelite

Ikelite 6148.10 Manuel d'utilisation et d'entretien

Ikelite

Ikelite 6140.54 Manuel utilisateur

Ikelite

Ikelite 69740 Manuel utilisateur

Ikelite

Ikelite 6860.03 Manuel utilisateur

Ikelite

Ikelite DS51 Manuel utilisateur

Ikelite

Ikelite S3 Manuel utilisateur

Ikelite

Ikelite Olympus E-3 Manuel utilisateur

Ikelite

Ikelite SLR-DC 6855.10 Manuel utilisateur

Ikelite

Ikelite 46064 Manuel utilisateur

Ikelite

Ikelite 6970.03 Manuel utilisateur

Ikelite

Ikelite 6148.23 Manuel utilisateur

Ikelite

Ikelite FinePix F50fd Manuel d'utilisation et d'entretien

Ikelite

Ikelite Olympus Mju780 Manuel utilisateur

Ikelite

Ikelite 6147.16 Manuel utilisateur

Ikelite

Ikelite 6430 W-30 Manuel utilisateur

Ikelite

Ikelite 4103.51TTL Manuel utilisateur

Ikelite

Ikelite 6241.34 Canon A3400 IS Manuel du propriétaire

Ikelite

Ikelite DCR-HC14 Manuel du propriétaire

Ikelite

Ikelite 5510.75 Manuel utilisateur

Ikelite

Ikelite 6147.89 Manuel utilisateur

Ikelite

Ikelite DSC-HX20V Manuel utilisateur

Manuels Accessoires pour appareils photo populaires d'autres marques

Viltrox

Viltrox EF-NEX Instructions d'installation

Calumet

Calumet 7100 Series CK7114 Manuel utilisateur

Ropox

Ropox 4Single Series Manuel utilisateur

Cambo

Cambo Wide DS Digital Series Mode d'emploi

Samsung

Samsung SHG-120 Manuel utilisateur

Ryobi

Ryobi BPL-1820 Manuel d'utilisation

Aegis

Aegis ABL-36020P Manuel utilisateur

Pentax

Pentax Data Back Fc Manuel utilisateur

Fantasea

Fantasea EyeGrabber F Series Manuel utilisateur

Honeywell

Honeywell HDZ20HD Manuel utilisateur

EGO

EGO BA1400T Manuel utilisateur

Sima

Sima SRW-62 Manuel utilisateur

Shape

Shape A7SSMKIT Manuel utilisateur

Slide Kamera

Slide Kamera HST-2 Manuel utilisateur

Power works

Power works 2902613 Manuel utilisateur

SES

SES SE-2047-2 Manuel utilisateur

Olympus

Olympus PT-EP05L Manuel utilisateur

Starlite

Starlite OctoDome nxt Manuel utilisateur