IHP SV4.5HTKCT Manuel utilisateur

Required Tools

• Safety Glasses

• Protective Work Gloves

• Carpenter’s Level

• Phillips Screwdriver

General Information

This document details installation instructions for the SV4.5HTKCT, SV4.5HTKCT20, all SFKITXXCT, and

SF4.5HTKCT horizontal compact termination kits. Information provided here supplements the instructions provided

with each ﬁreplace and may be redundant to that information. The intent of this document is to provide complete

instructions for the aforementioned terminations, particularly any instructions exclusive to the installation of

these terminations.

These horizontal compact terminations are intended for use ONLY with the following IHP direct-vent gas ﬁreplaces:

• Aries 33”, -35”, -40”

• DRT/DRC2033, -2035, and -2040

• VeniceLightsTEN, VeniceLightsTEP

• DRL4543TEN, DRL4543TEP

These terminations may not be used with other models. The terminations covered by this document seamlessly

integrate with all other components of the approved ﬁreplaces, and when installed in accordance with the directions

provided here—and with the ﬁreplace—constitute a complete, approved and listed installation.

Horizontal Compact

Termination Kits

P/N 900080-00

REV. B, 04/2018

HEARTH PRODUCTS

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR IHP HORIZONTAL COMPACT

TERMINATION KITS FOR USE WITH DIRECT-VENT GAS FIREPLACES

[Kit models SV4.5HTKCT, SV4.5HTKCT20, all SFKITXXCT, SF4.5HTKCT]

WARNING

HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO

TOUCH GLASS.

• Install only when ﬁreplace is OFF and COLD.

• Fireplace surfaces get EXTREMELY HOT!

• The glass on the front of the ﬁreplace reaches EXTREMELY HIGH temperatures and can cause severe

burns if touched. Even after the gas is turned off, ﬁreplace surfaces remain extremely hot.

• Keep children away from an operating ﬁreplace. Closely supervise children in any room where a

ﬁreplace is operating to prevent contact with glass.

CUS

Report No. F13-94

Installation

900080-00, 04/2018

Innovative Hearth Products

IHP Direct-Vent Gas Fireplaces

Install the Horizontal Termination Vent System

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting

according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the

current standards of CAN/CGA-B149.1 in Canada.

Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier.

Dégagement conforme aux codes d’installation locaux et aux exigences du foumisseunde gaz.

Installation Preparation

Refer to the ﬁreplace installation instructions for more information.

1. Analyze the vent route and determine the number of vent sections and elbows required.

2. Frame the exterior wall opening.

3. Frame the ceiling opening.

4. If required, install the vent gasket.

5. Attach the vent components to the ﬁreplace.

6. Attach the vent components to each other.

7. Install the ﬁrestop/spacer at the ceiling.

8. Support the vertical run sections.

9. Change vent direction.

10. Continue installation of horizontal/inclined sections.

11. Assemble the vent run to the exterior wall.

12. Attach the termination adaptor.

13. Install the ﬁrestop/spacer at the exterior wall.

Install the Compact Termination

1. From outside the exterior wall, slide the collars of the termination onto the adaptor (the outer over the outer and

the inner inside the inner) until the termination seats against the exterior wall surface to which it will be attached.

NOTE: Orient the housing of the termination with the arrow pointed upwards.

2. Secure the termination to the exterior wall.

NOTE: The horizontal termination must not be recessed into the exterior wall or siding by more than the 1 1/4”

(32 mm) (Figure 1).

If the venting exits the building below grade, or close to grade, see the appliance manual for available snorkel

terminations. The termination must be above grade and above the expected level of snow accumulation.

WARNING

The vent termination is hot while in operation and for a period of time following the use of the ﬁreplace.

To prevent contact with hot surfaces, use a horizontal termination guard; available for purchase at your local dealer.

The horizontal terminations have been designed to perform in a wide range of weather conditions. Our

terminations meet or exceed industry standards.

When selecting the locations of your horizontal terminations, do not place the termination where water from

eaves and adjoining rooﬂines may create a heavy ﬂow of cascading water onto the termination cap. If the cap

must be placed where the possibility of cascading water exists, it is the responsibility of the builder to direct the

water away from the ter mination cap by using gutters or other means.

Take care to carefully follow the installation instructions for the termination, including the use of silicone caulking

where required.

Installation

900080-00, 04/2018

Innovative Hearth Products

IHP Direct-Vent Gas Fireplaces

Figure 1: Installing the Horizontal Termination

Termination

10-1/2”

(267mm)

7”

(178)

5-1/8”

(130 mm)

12-1/8”

(308 mm)

Note: Centerline of Vent Piping is

NOT the Same as the Centerline of

the Framed Opening.

6 to 48” Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

Min. Distance to Base

of Appliance.

Base of Appliance

3”

(76 mm)

1”

(25.4 mm)

Adaptor

SV4.5RCH

To help minimize water

infiltration it is recommended that

the Firestop/Spacer (SV4.5HF)

be installed on the exterior

side of the wall.

See the installation manual for the minimum

distance to the base of the ﬁreplace.

NOTE: To help minimize water inﬁltration install the ﬁrestop/spacer (SV4.5HF) on the exterior side of the wall.

Figure 2: Venting Connection and Exterior Wall Recessing of the Horizontal Compact Termination

(SV4.5HTKCT)

Siding

Stucco 1-1/4” Maximum Recess of

the Square Termination into

Exterior Finishing Material

Exterior Surface of

Framing

6” to 9-1/4”

(152 to 235 mm)**

Exterior Surface of Siding

Interior Surface of

Finished Wall

Maximum wall thickness

9-1/4” (235 mm)**

Maximum Extent of

Vent Run Sections

Relative to Exterior

Surface of Framing

Last Vent Section. Use

Telescopic Vent

Section (SV4.5LA), If

Necessary

Adaptor

SV4.5RCH

*Use silicone caulking to

seal the top and sides of

the termination, up to the

underlayment, stucco, or

masonry wall surface.

*Caulk

** For thicknesses greater

than 10” (254 mm) see

Table 1.

Installation

900080-00, 04/2018

Innovative Hearth Products

IHP Direct-Vent Gas Fireplaces

Table 1: Venting Components Required for Various Exterior Wall Thicknesses, when using Typical Termination Kits

Vent Components Required Exterior Wall Thickness

Termination Kit Only 6–9 1/4” (152–235 mm)

Termination Kit and 6” Vent Section (SV4.5L6) 10 3/4–14” (273–356 mm)

Termination Kit and 12” Vent Section (SV4.5L12) 16 3/4–20” (426–508 mm)

Termination Kit and Telescopic Section (SV4.5L12) 11 3/4–20” (299–508 mm)

NOTE: See Figure 2 for wall thickness ranges when using SV4.5HTKCT termination kit.

Horizontal Vent Figures/Tables

NOTE: Secure Vent®rigid vent pipe and terminal are shown in the ﬁgures. Secure Flex®ﬂexible vent pipe and

terminal may also be used.

NOTE: Two (2) 45° elbows may be used in place of one (1) 90° elbow. The same rise to run ratios, as shown in the

venting ﬁgures for 90° elbows, must be followed if 45° elbows are used.

NOTE: Maintain the horizontal/inclined run in a straight (no dips), slightly elevated plane. The recommended incline

is approximately 1/4” per 1 ft (20 mm per 1 m) horizontal, in a direction away from the ﬁreplace. Smaller rise per

foot run ratios are acceptable all the way to at or near level. Use a carpenter’s level to measure from a constant

surface and adjust the support straps as necessary.

NOTE: SV4.5VF (Secure Vent), SF4.5VF (Secure Flex) ﬁrestop/spacer must be used any time vent pipe passes

through a combustible ﬂoor or ceiling. SV4.5HF (Secure Vent), SF4.5HF (Secure Flex) ﬁrestop/spacer must be used

any time vent pipe passes through a combustible wall.

WARNING

Do not join separate sections of concentric ﬂexible vent together.

P/N 900080-00 Rev. B 04/2018

IHP reserves the right to make changes at any time, without notice, in design, materials,

speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local

distributor for ﬁreplace code information.

1769 East Lawrence Street • Russellville, AL 35654

Ce manuel convient aux modèles suivants

Autres manuels IHP Accessoires de cheminée

IHP

IHP Snap-Pak Manuel utilisateur

IHP

IHP FP4125-BDVI32 Manuel utilisateur

IHP

IHP Envy AKC-CLS-DLSCNV Manuel utilisateur

IHP

IHP WINSLOW PS40 Manuel utilisateur

IHP

IHP MAGNIFLAMEOD24NE Guide de démarrage rapide

IHP

IHP OAK-UVFRC Manuel utilisateur

IHP

IHP RDV-CONTF-BLK Manuel utilisateur

IHP

IHP GCKSMS557051NP Manuel utilisateur

IHP

IHP BWBK Manuel utilisateur

IHP

IHP SEREFINA CI1500 GCK LP Manuel utilisateur

IHP

IHP STK-LIN60-B KIT Manuel utilisateur

IHP

IHP 900077-07 Manuel utilisateur

IHP

IHP 900935-00 Manuel utilisateur

IHP

IHP F2460 Manuel utilisateur

IHP

IHP 36LBFOD-BS Manuel utilisateur

IHP

IHP EPIC-TRIM-B Manuel utilisateur

IHP

IHP GCK-LS Manuel utilisateur

IHP

IHP PCBE-36 Manuel utilisateur

IHP

IHP F1762 Manuel utilisateur

IHP

IHP RDV-CONTF-BLK Manuel utilisateur

IHP

IHP FBK-LIN Manuel utilisateur

IHP

IHP BLB36SF Series Manuel utilisateur

IHP

IHP SF-HTSS Series Manuel utilisateur

IHP

IHP PCBE-325 Manuel utilisateur

Manuels Accessoires de cheminée populaires d'autres marques

Valor

Valor L2 1700K Manuel utilisateur

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur

Cooke

Cooke Glass Wind Guard Manuel utilisateur