IHP STK-LIN60-B KIT Manuel utilisateur

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 1

STK-LIN60-B KIT

INSTALLATION INSTRUCTIONS FOR STK-LIN60-B KIT

[FOR USE IN ALLUMEDLX60TEN-B, ALLUME60TEN-B, DRL4060TEN-B, AND DRL6060TEN-B FIREPLACES]

HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 901058-00 REV. NC 07/2020

WARNING

This kit must be installed by a qualiﬁed installer,

service agency, or gas supplier at the time of the

ﬁreplace installation. These instructions must

be used in conjunction with the installation and

operation manual provided with the ﬁreplace.

IMPORTANT NOTICE

STK-LIN60-B KIT IS REQUIRED FOR UPGRADING FIREPLACE

TO A SEE-THRU APPLICATION.

IMPORTANT NOTICE

BLOWER USE IS NOT COMPATIBLE WITH THE STK-LIN60-B

KIT.

GENERAL INFORMATION

The STK-LIN60-B KIT is designed to upgrade the ﬁreplace to a

see-thru application.

When Installing this kit, reference the framing dimensions for the

see-thru application and follow the framing instructions shown on

the ﬁreplace installation Instructions. Follow all other installation

requirements for the ﬁreplace as detailed in the installation manual.

IMPORTANT! CONVERT THE FIREPLACE TO A SEE-THRU

APPLICATION BEFORE INSTALLING INTO THE FRAMING.

REFER TO INSTALLATION INSTRUCTIONS AND CARE AND OPERA-

TIONS MANUAL (IICO)FOR FRAMING DETAILS BEFORE INSTALLING

THIS KIT.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE FIREPLACE APPLY TO

THESE INSTRUCTIONS.

Kit Components

2 ea. Nailing Flange side

2 ea. Tile Stop L/R

2 ea. Tile Stop Top/Bottom

2 ea. Sight Obstructor

1 ea. Standoff Heatshield

1 ea. Door Access Cover

1 ea. Fireboard Assembly

1 ea. Glass Door

1 ea. Rear Standoff Assembly

1 ea. Barrier

22 ea. #10 Hex Head Screw

15 ea. #8 Phillips Head Screw

36 ea. Bugle drywall Screws

TOOLS REQUIRED (not included)

Electric Drill/Driver Gun

Phillips Screwdriver Bits

5/16 Nut Driver

5/16” Wrench

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference

Fireboard

Assembly

Nailing

Flange L/R

Tile Stops

L/R

Tile Stops

Top/Bottom

Door Access

Cover

Glass

Door

Barrier

STK-LIN60-B KIT

Cat. No. Model Number Description

F4410 STK-LIN60-B KIT Kit, Linear 60 See-Thru

Table 1 See Figure 1

Figure 1 - STK-LIN60-B KIT

Sight Obstructors

Standoff

Heatshield

Rear Standoff

Assembly

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ALLUMEDLX60TEN-B and DRL6060TEN-B model only, disconnect

blower assembly power cord from the ﬁreplace control module

harness. Discard blower assembly and blower harness as blowers

are not compatible on a see-thru application.

Preparing Fireplace for See-Thru Application

1. Install rear standoff assembly, as shown in Figure 2, using eight

(8) of the #10 hex head screws.

2. Install the standoff heatshield, using three (3) #10 hex head screws

(two in the lower front, and one going upward into the standoff

assembly). See Figure 2.

3. Remove the rear heatshield assembly by removing the 12 hex head

screws fastening it to the back of the ﬁreplace. This assembly will

not be reused and can be discarded (see Figure 2).

Figure 2

Figure 3

Figure 4

Rear Standoff

Assembly

Rear Heatshield

Assembly

Standoff

Heatshield

False Door

4. Remove the ten (10) hex screws fastening the false door to the

ﬁreplace. Lift upward and outward to remove false door. Remove

any gasket material that may have been left behind on the ﬁrebox

door mating surface. This part will not be reused and can be

discarded (see Figure 3).

5. Place the bottom edge of the door assembly into the door channel

on the ﬁrebox. The tabs on the bottom of the door on each side

will fall into corresponding slots on the door channel of the ﬁrebox

(see Figure 4).

6. While holding the door closed, place one of the sight obstructors

against the door as shown. With both the door and sight obstructor

in place, fasten them to the ﬁrebox together using ﬁve (5) #10

hex head screws(see Figure 4).

Door Assembly

Bottom Door Edge,

Tab and Channel

Sight

Obstructor

7. Attach the remaining sight obstructor to the upper heatshield as

shown using ﬁve (5) #10 hex head screws (see Figure 5).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 3

Figure 5

Upper Heatshield

Sight Obstructor

8. Partially install two (2) #8 Phillips head screws into the upper

left and right tile stop mounting holes. Partially loosen (DO NOT

REMOVE) the two (2) lower outside tile stop Phillips head screws.

Hang the top and bottom tile stops on those outside screws and

install the remaining three (3) #8 Phillips head screws on each

tile stop (see Figure 6).

9. Using six (6) #8 Phillips head screws,install the side tile stops

as shown in Figure 6.

10. Bend both side door access cover supports upward until they

are ﬂat. Bend the center door access cover toward the door on

the ﬁreplace (see Figures 6 and 7).

11. Install the door access cover onto the door access cover supports,

inserting tabs on cover into the slots on the cover support shown

in Figure 7.

12. Install the barrier by sliding it upward into the top barrier channel,

then push back slightly on the bottom, and lower it into the lower

barrier channel (see Figure 7).

Door Access

Cover

Slot

Upper and Lower

Barrier Channels

Barrier Screen

Door Access

Cover

Door Access

Cover Support

Figure 7

Figure 6

Partially Loosen,

Both Sides

Do Not Remove Partially Install

Both Sides

Door Access

Cover Supports

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 8

Nailing

Flange

Mounting

Screws

13. Proceed with installation of the ﬁreplace into the framing per

instructions in the Installation and Operation Manual provided

with the ﬁreplace.

14. Once the ﬁreplace is installed in the framing, install the nailing

ﬂanges. Loosen (DO NOT REMOVE) the three (3) hex head

mountingscrewsonbothsidesoftheﬁreplace showninFigure

8. Slide the nailing ﬂange onto those screws on both sides,

with the bottom most slot going onto the bottom most screw.

Once in place, using a 5/16” wrench, tighten the mounting

screws through the access holes in the nailing ﬂange (see

Figure 8, Page 4).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 8 - Flush Wall Installation Without HeatFlo Kit

Figure 9 - Flush Wall Installation with HeatFlo Kit Installed

Fireplace

HeatFlo Trim

in Place

FINISHING FIREPLACE

The appliance is designed to mate with 1/2” wall sheathing materials

such as drywall, plywood, wood composites, or non-combustible

materials.

Finishing and Sealing Joints

All joints between the ﬁnished wall sheathing and the appliance

must be sealed with non-combustible materials. Sealants, such

as caulk or mastic used to seal the gap between the wall and the

ﬁreplace, should be rated at a minimum continuous exposure to

300 ºF.

Finishing Around Opening with Gypsum Wallboard

Gypsum wallboard (drywall) joints adjacent to the ﬁreplace opening,

including the non-combustible board on the appliance, require

special attention to minimize cracking. When installing gypsum

wallboard around the ﬁreplace, install the hole for the ﬁreplace

opening in a single wallboard sheet, if possible. This will minimize

the joints adjacent to the ﬁreplace opening.

Tape wall board joints around the ﬁreplace opening with ﬁberglass-

mesh tape. It will provide a more crack-resistant joint than paper

tape. Fill, smooth and ﬁnish wall joints with chemically setting-type

joint compound. It will provide a more crack-resistant joint than

air-drying light-weight compound.

NOTE: NEVER install combustible material (wall ﬁnish, surround,

trim, etc.) on, in front of, or overlapping any part of the ﬁreplace

front face.

NOTE: Non-combustible ﬁreboard is provided with the ﬁreplace.

DO NOT SUBSTITUTE.

Installing Fireboard

1. Using 1” self drill bugle drywall screws (supplied), install non-

combustible ﬁreboard at bottom, sides and top of ﬁreplace

face (See Figure 8).

2. Apply 1/2” wall sheathing materials such as drywall, plywood,

wood composites, or non-combustible materials to the rest

of the wall. NOTE: When applying drywall, minimize number

of joints to reduce potential for cracking.

NOTE: Factory supplied tile stops protrude 3/4" from unit and

will allow installation of standard tile and thin set on top of the

noncombustible ﬁreboard.

NOTE: The HeatFlo Register Trim ships from the factory painted

black and it may be painted another color to match the wall color.

Use high temperature paint with a minimum 400°F continuous rating

(Figure 9). Do not ﬁnish over any of the opening in the trim outlet.

Innovative Hearth Products (IHP) reserves the right to make changes at any

time, without notice, in design, materials, speciﬁcations, prices and also

to discontinue colors, styles and products. Consult your local distributor for

ﬁreplace code information.

P/N 901058-00 REV. NC 07/2020 1769 East Lawrence Street • Russellville, AL 35654

Ce manuel convient aux modèles suivants

Autres manuels IHP Accessoires de cheminée

Manuels Accessoires de cheminée populaires d'autres marques

Valor

Valor L2 1700K Manuel utilisateur

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur

Cooke

Cooke Glass Wind Guard Manuel utilisateur