IHP OAK-UVFRC Manuel utilisateur

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

HEARTH PRODUCTS

KITS AND ACCESSORIES

750206M

REV. B 05/2017

TOOLS / SUPPLIES REQUIRED

• 5/16” Nut driver or Socket • Duct Tape • Silicon Type Caulking

GENERAL INFORMATION

This kit is for use with various IHP vent-free ﬁreboxes when installed in

conventional construction. These kits have an air gate assembly which allows

adjustment of the amount of outside air delivered to the ﬁre for combustion.

Only one air kit, located on the right side of the ﬁrebox, is required.

READ ALL THE STEPS BEFORE STARTING THE INSTALLATION

THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE

INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE

APPLIANCE APPLY TO THESE INSTRUCTIONS.

If you encounter any problems, need clariﬁcation of these instructions

or are not qualiﬁed to properly install this kit, contact you local distribu-

tor or dealer.

If any of these parts are missing or damaged, contact your dealer or IHP.

us.com for referral information.

Retain These Instructions for Future Reference

INSTALLATION INSTRUCTIONS

1. Remove the outside air knock-out on the right hand side of appliance

(See Figure 2 for location).

2. Assemble the Air Gate as shown in Figures 3 and 4.

3. Take the Air Gate Assembly and feed the arm through the round opening

(see Figures 5 and 6)and then through the side frame opening. Ensure

the air gate arm remains attached to the air gate (see Figure 7).

Figure 1 - Kit Contents (see Table 1)

651

Remove Outside

Air Knock-Out

Right Hand Side

of Firebox

Figure 2

Side View of Arm

installed into Air

Gate.

Air Gate Assembly

Air Gate Arm

Figure 3

When assembled onto appliance, the notch

here must be positioned down as shown.

Outside View of

Arm installed

into Air Gate.

Air Gate Arm

Air Gate

Figure 4

WARNING

Do not operate the combustion air gate with a ﬁre in the ﬁrebox

unless all components of this kit have been installed.

Air Gate Arm

Figure 5

Right Side

Panel on

Firebox

Air Gate

Outside Air Gate & Duct Kit

Cat. No. Model Description

H3991 OAK-UVFRC Outside Air Gate & Duct Kit

KIT CONTENTS

1 ea. Air Gate Assembly (1)

1 ea. Arm, Air Gate (2)

1 ea. Bracket, Air Gate Arm (3)

1 ea. Collar, Outside Air (4)

1 ea. Duct, 4” (5)

1 ea. Hardware Kit (9 long screws & 4 short screws) (6)

1 ea. Instruction Sheet (7)

OAK-UVFRC OUTSIDE

AIR GATE & DUCT KIT

OAK-UVFRC OUTSIDE AIR GATE & DUCT KIT

[FOR USE WITH MODELS ATLAS36/42, ORION32/36/42, VRT2536/42, VRT3132/36/42, VRT3536/42, AND VARIOUS LHP LEGACY APPLIANCES]

fire-parts.com

5. Secure the air gate arm support bracket (item

#3 in Figure 1) as shown in Figure 9.

4. Secure the air gate to the ﬁrebox as shown

in Figure 8.

7. Attach ﬂexible duct to the outside air collar

using two (2) short screws (provided), then

wrap with duct tape as shown in Figure 11.

P/N 750206M REV. B 05/2017

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Hold the air gate arm and align the air gate assem-

bly to ﬁt ﬂush in the opening.

Figure 6

Figure 12

8. Duct Hole Framing: Cut or frame a hole through

the outside of the enclosure for the installation

of the duct inlet hood. A 5" (127 mm) diameter

hole is required. Feed the loose end of the ﬂexible

duct through the hole cut for the inlet hood and

attach to the collar on the inlet hood using two

(2) short screws (provided), then wrap with duct

tape. Insert the hood into the opening. Secure in

place with nails driven through the holes in hood

ﬂange. Seal with noncombustible waterproof

silicon type caulking. If additional duct is needed,

use Class 0 metallic air duct (refer to Figure 12).

NOTE: The Class 0 metallic air duct can be routed

out the back wall or side wall, up through the ceiling

or ﬂoor joists to an outside wall. Check local build-

ing codes for any restrictions. We recommend that

the inlet be at least four (4) feet above grade level.

4" (102 mm)

Class 0 air duct

Hood

Air Inlet

Secure the hood

to a vertical post

with the inlet posi-

tioned downward.

• IN COLD CLIMATES

THE AIR DUCT SHOULD

BE INSULATED.

CAUTION

Do not install the air inlet in the attic,

garage, near combustible gases (i.e.

paint, gasoline, etc.) or where there

is a fuel burning appliance or where

the opening could be blocked by snow,

bushes or other obstacles.

6. Secure the outside air collar (item #4 in Figure

1) as shown in Figure 10.

Innovative Hearth Products

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and the discontinuance of colors, styles and products. Consult your local distributor

for ﬁreplace code information.

Air Gate Arm

Front right

side of ﬁrebox

opening

Locate this opening

Feed the bent end of the air gate arm

into this notched opening.

Figure 7

OPEN POSITION

CLOSED POSITION

Air

Gate

Secure the Air Gate to the ﬁreplace with four

(4) long screws (provided) through the outside

holes (indicated by arrows).

Right Side

of Firebox

Figure 8

Ensure this

notch is

positioned

on the

bottom half

of air gate.

Locate this slot on right

side panel of ﬁrebox.

Slot

Insert the arm support bracket as shown.

Adjust arm as necessary to rest on the bracket

Slot

Bracket

Secure the

bracket with a

screw provided.

Long

Screw

Figure 9

Bracket

Outside

Air

Collar

Secure the outside air collar over the air gate

using the four (4) long screws (provided)

through the inside holes (indicated by arrows).

Figure 10

Collar

Secure the duct to

the collar using

duct tape as

shown.

Figure 11

fire-parts.com

Autres manuels IHP Accessoires de cheminée

IHP

IHP Envy AKC-CLS-DLSCNV Manuel utilisateur

IHP

IHP BLB36SF Series Manuel utilisateur

IHP

IHP H5872 Manuel utilisateur

IHP

IHP GCKSMS557051NP Manuel utilisateur

IHP

IHP AK4 Manuel utilisateur

IHP

IHP H0776 Manuel utilisateur

IHP

IHP BNZN Manuel utilisateur

IHP

IHP RDV-CONTF-BLK Manuel utilisateur

IHP

IHP GAB Series Manuel utilisateur

IHP

IHP CDFBBK-35 Manuel utilisateur

IHP

IHP MERIT ZEN GARDEN MLDVTCD-35 Manuel utilisateur

IHP

IHP UZY-7-B Manuel utilisateur

IHP

IHP HeatFlo Kit Manuel utilisateur

IHP

IHP 900077-07 Manuel utilisateur

IHP

IHP Montebello Series Manuel utilisateur

IHP

IHP WINSLOW PS40 Manuel utilisateur

IHP

IHP WS-CI150 Manuel utilisateur

IHP

IHP FP4125-BDVI32 Manuel utilisateur

IHP

IHP PCBM-42 Manuel utilisateur

IHP

IHP STK-LIN60-B KIT Manuel utilisateur

IHP

IHP RIVROCK-25PK Manuel utilisateur

IHP

IHP RDV-BRK-STD Manuel utilisateur

IHP

IHP VF F3784 Manuel utilisateur

IHP

IHP RDV-CONTF-BLK Manuel utilisateur

Manuels Accessoires de cheminée populaires d'autres marques

Valor

Valor L2 1700K Manuel utilisateur

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur

Cooke

Cooke Glass Wind Guard Manuel utilisateur