Ideal Boilers SE9 RS Manuel utilisateur

users guide

Classic

Your Ideal users guide

See reverse for Classic installation & servicing instructions

ENGINEERED FOR PEACE OF MIND

When replacing a part on this appliance use only spare parts that you can be assured

conform to the safety and performance specification that we require. Do not use

reconditioned or copy parts that have not been clearly authorised by Ideal Boilers.

SE9 RS, SE12 RS, SE15 RS

& SE18 RS

Classic SE RS - Users

Flammable materials must not be placed in close proximity to

the appliance. Materials giving off flammable vapours must not

be stored in the same room as the appliance.

f. Under NO circumstances should any of the sealed components

on this appliance be used incorrectly or tampered with.

Minimum clearances

A clearance of 533mm (21") MUST be available at the front of the

boiler for servicing.

The minimum clearances given below MUST be complied with in

order to maintain the safe running of the boiler .

Above the boiler 100 mm (4")

At each side of the boiler 5 mm (1/4")

Underneath the boiler 100 mm (4")

In front of the boiler 75 mm (3")

To light the boiler. RefertoFrame1

If a programmer is fitted, refer to separate instructions for the

programmer before continuing.

1. CHECKTHATTHEELECTRICITYSUPPLYTOTHEBOILERISOFF.

2. Open the controls access door by hinging downwards.

3. Ensure that the gas inlet cock (C) is OPEN.

4. If an overheat thermostat is fitted press the overheat reset button

(D), located as shown in Frame 1.

5. SwitchONthe electricitysupplytothe boiler. Checkthatallexternal

controls, e.g. room thermostat etc., are ON.

6. Turn the boiler thermostat knob (B) to position 6. After about 15

seconds the boiler will light automatically - this can be viewed

through the sightglass (A).

Set the boiler thermostat to the desired position.

7. Close the controls access door.

INTRODUCTION

It is essential that the instructions in this booklet are

strictly followed, for safe and economic operation of

theboiler.

Current Gas Safety (Installation & Use)

Regulations or rules in force.

In your own interest, and that of safety, it is the law that

this boiler must be installed by a CORGI registered installer

orin IE a competent person, in accordancewith theabove

regulations.

Electricity Supply

This appliance must be efficiently earthed.

Supply: 230 V ~ 50 Hz. The fusing should be 3A.

Connection must be made in a way that allows complete

isolationof the electricalsupplysuch as adoublepole switch

having a 3mm (1/8") contact separation in both poles, or a

plugand socket, servingonly the boilerandsystem controls.

The means of isolation must be accessible to the user after

installation.

IMPORTANT NOTES

This appliance must not be operated without the casing

correctly fitted and forming an adequate seal.

If the boiler is installed in a compartment then the

compartment MUST NOT be used for storage purposes.

The ventilation provided for the boiler during installation MUST

NOT be blocked and a check should be made periodically

that the ventilation areas are free from any obstruction.

If it is known or suspected that a fault exists on the boiler then

it MUST NOT be used until the fault has been corrected by a

CORGI registered installer or in IE a competent person.

CAUTION. To avoid the possibility of injury during the installation, servicing or cleaning of

this appliance, care should be taken when handling edges of sheet steel components.

Model GC Appliance No

Classic SE9 RS........................... 41 395 44

Classic SE12 RS .........................41 395 45

Classic SE15 RS ......................... 41 395 46

Classic SE18 RS .........................41 395 99

Classic SE RS (Natural Gas Models Only)

Classic SE RS - Users

BOILER CONTROLS

View inside controls area

LEGEND

A. Sightglass

B. Thermostat knob

C. Gas service cock (shown in the OPEN position)

D. Overheat thermostat reset button (if fitted)

THE LOG BOOK SHOULD BE COMPLETED AFTER

EACH SERVICE AND KEPT WITH THESE

INSTRUCTIONS

Winter conditions, i.e. central heating and domestic hot water, the

thermostat should be set at position 5 or 6.

Summer conditions, i.e. domestic hot water only, the thermostat

should be set at position 3.

These settings, however, are offered for general guidance only

and other settings may be found preferable, dependent upon the

type of system installed or as recommended by the installer.

Approx. flow temperatures for the boiler thermostat settings are:

KnobSetting Flow Temperature

°C °F

156 133

261 142

366 152

472 161

577 170

682 180

To shut down the boiler

1. For short periods

Turn the boiler thermostat (B) to '0' to turn the boiler OFF.

When heating is again required, turn the thermostat knob to

the desired heat setting.

2. For longer periods

Turn the boiler thermostat (B) to '0' to turn the boiler OFF.

Switch the electricity supply to OFF.

To relight the boiler

Repeat the procedure 1 - 7, detailed in 'To light the boiler'.

Frost protection

If no frost protection is provided and frost is likely during a short

absence from home, leave the heating controls at a reduced

temperature setting.

For longer periods, the entire system should be drained -

including the domestic water supply. If the system includes a

frost thermostat then, during cold weather, the boiler should

be turned OFF at the time switch(es) ONLY. The mains supply

should be left switched ON, with the boiler thermostat left in the

normal running position.

All CORGI registered installers carry a CORGI ID card, and have a registration number. Both should be recorded in

your Benchmark Log Book. You can check your installer by calling CORGI direct on 01563 72300

2345

CL1986

Controls

door

CL 1987

Caradon Ideal Limited

pursues a policy of

continuing improvement in

the design and performance

of its products. The right is

therefore reserved to vary

specification without notice.

Ideal Boilers, P.O. Box 103,

NationalAve.,Kingstonupon

Hull,HU54JN. Telephone:

01482 492 251.

Fax: 01482 448 858.

RegistrationNo.London 322137.

The code of practice for the installation,

commissioning & servicing of central heating systems

Caradon Ideal Limited is a member of the Benchmark

initiative and fully supports the aims of the

programme. Benchmark has been introduced to

improve the standards of installation and

commissioning of central heating systems in the UK

and to encourage the regular servicing of all central

heating systems to ensure safety and efficiency.

Ideal Consumer Helpline Tel: 01482 498 660

www.idealboilers.com

THIS SYMBOL IS YOUR

ASSURANCEOFQUALITY

Theseappliances are designedfor use withNatural

Gasonly. Theyhave been testedand conformwith the

provisionsof BS.6332 andBS. 5258.

CERTIFIED PRODUCT

Manufactured under a BS EN

ISO 9001:2000 Quality System

accepted by BSI.

Natural Gas appliances are service

listed by British Gas

Boiler overheat thermostat

(if fitted)

If the boiler is fitted with a safety 'cutout' thermostat this will

shut down the boiler in the event of overheating.

Should this occur allow the boiler to cool, press the reset button

(D) then relight as detailed in steps 1-7 in 'To light the boiler'.

If the cutout condition still persists then turn off the boiler and

consult a CORGI registered installer or in IE a competent person.

Loss of system water pressure

(Boilers fitted with Classic Sealed System Units only)

If the red arrow on the module pressure gauge is set above zero

and the system pressure is seen to fall below this value over a

periodoftimethenawaterleakisindicated.In this event a CORGI

registered installer or in IE a competent person should be

consulted.

DO NOT OPERATE THE BOILER IF THE PRESSURE HAS

REDUCEDTOZEROFROMTHEORIGINALSETTING.

Escape of gas

Should a gas leak be suspected, contact your local gas supplier

without delay.

Do NOT search for gas leaks with a naked

flame.

Cleaning

For normal cleaning simply dust with a dry cloth.

To remove stubborn marks and stains, wipe with a damp cloth

and finish off with a dry cloth.

Do NOT use abrasive cleaning materials.

Maintenance

The appliance should be serviced at least once a year by a

CORGI registered installer or in IE a competent person.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ideal Boilers Chaudière

Ideal Boilers

Ideal Boilers Mexico Super RS 3/60P Fiche technique

Ideal Boilers

Ideal Boilers INDEPENDENT+ COMBI 24 Guide de l'utilisateur

Ideal Boilers

Ideal Boilers Classic LXFF 230 Fiche technique

Ideal Boilers

Ideal Boilers 330 RDI Manuel utilisateur

Ideal Boilers

Ideal Boilers Mexico Super 100 FF Fiche technique

Ideal Boilers

Ideal Boilers Harrier GTS Manuel utilisateur

Ideal Boilers

Ideal Boilers Falcon GTS 4 Manuel utilisateur

Ideal Boilers

Ideal Boilers Classic FF 360 Manuel utilisateur

Ideal Boilers

Ideal Boilers CF3/100 Fiche technique

Ideal Boilers

Ideal Boilers Classic FF230 Fiche technique

Ideal Boilers

Ideal Boilers LOGIC Combi ES24 Manuel utilisateur

Ideal Boilers

Ideal Boilers British Gas RD2 Guide de l'utilisateur

Ideal Boilers

Ideal Boilers FF 350 Manuel utilisateur

Ideal Boilers

Ideal Boilers VOGUE COMBI C26IE Manuel utilisateur

Ideal Boilers

Ideal Boilers excel HE C24 Manuel utilisateur

Ideal Boilers

Ideal Boilers HE15 Manuel utilisateur

Ideal Boilers

Ideal Boilers Mexico Super CF 3/40 Guide de l'utilisateur

Ideal Boilers

Ideal Boilers Mexico Super CF495 Guide de l'utilisateur

Ideal Boilers

Ideal Boilers Classic FF 360 Manuel utilisateur

Ideal Boilers

Ideal Boilers LOGIC SYSTEM S15 Manuel utilisateur

Ideal Boilers

Ideal Boilers Classic LX RS 230 Manuel utilisateur

Ideal Boilers

Ideal Boilers istor HE260 Manuel utilisateur

Ideal Boilers

Ideal Boilers HE15 Manuel utilisateur

Ideal Boilers

Ideal Boilers Maximiser SE Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur