ICRealtime AVS-4MD5110-VIR Manuel utilisateur

HDAVS Camera User’s Manual

Version 1.0.0

Table of Contents

1General Introduction ..................................................................................................................1

1.1 Overview........................................................................................................................1

1.2 Features.........................................................................................................................1

2Device Framework .....................................................................................................................2

3Installation....................................................................................................................................3

4Menu.............................................................................................................................................5

4.1 HAVRSettings ...............................................................................................................5

4.2 Menu Operation............................................................................................................5

Appendix ⅠMaintenance...................................................................................................................7

Welcome

Thank you for purchasing our HDAVS camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

•All installation and operation here should conform to your local electrical safety codes.

•The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated DC 12V or AC24V in the IEC60950-1. (Power supply requirement is

subject to the device label).

•Please install easy-to-use device for power off before installing wiring, which is for emergent power

off when necessary.

•Please check if the power supply meets the requirements of working voltage of the camera before

operating the device (The material and length of the power supply cable will influence terminal

voltage value).

•Please prevent the line cord from being trampled or pressed, especially the plug, power socket and

the junction from the device.

2．Environment

•Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus.

•Please transport, use and store the device within the range of allowed humidity and temperature.

•Please do not allow water and other liquid falling into the camera in case that the internal

components are damaged.

•Please keep the sound ventilation in case of heat accumulation.

•Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

•Please pack the device with standard factory packaging or material with same quality when

transporting the device.

•It is recommended to use the device together with lightning protection device to enhance lightning

protection effect.

•It is recommended to GND the device to enhance device reliability.

•It is advised to use qualified video transmission cable to improve video quality. It is recommended

to use RG59 coaxial cable or higher standard.

Warning

•Please use the standard accessories provided by manufacturer and make sure the device is

installed and fixed by professional engineers.

•Please prevent the device surface from the radiation of laser beam when using laser beam device.

iii

•Please do not provide two or more power supply modes for the device, otherwise it may cause

damage to the device.

Statement

•Please refer to the actual product for more details; the manual is just for reference.

•The manual will be regularly upgraded according to the product update; the upgraded content will

be added in the manual without prior announcement.

•Please contact the customer service for the latest procedure and supplementary documentation.

•The company is not liable for any loss caused by the operation which is not followed by the manual.

•Please refer to the company’s final explanation if there is any doubt or dispute.

1General Introduction

1.1 Overview

This series HDAVS camera conforms to the HDAVS standard. It supports video signal high-

speed long distance transmission without any delay. It can be controlled by the HAVR

conforming to the HDAVS.

1.2 Features

Adopt high performance CMOS image sensor, megapixel definition.

Support coaxial transmission of video, audio and control signal.

For 720P series, support RG59 coaxial cable transmission without any loss. The distance

is over 800m. For 1080P, 4M and 4K series, support RG59 coaxial cable transmission

without any loss. The distance is over 500m.

High speed, long distance real-time transmission.

Support HDAVS HD video and analog video output.

Support 3D noise reduction, excellent low illuminance performance.

Support ICR switch to realize surveillance both in the daytime and at night.

Support OSD menu adjustment parameters.

Support smart IR function.

Support WDR/DWDR function.

Support DC 12V power supply. (Some models support DC 12V/AC 24V power supply).

Support IP67 compliance.

Support IK10 compliance. (Only supported by vandal proof camera)

Can be applied to environments which requires high definition image, such as banking,

supermarket, telecom, government, school, airport, factory, hotel, museum and etc.

2Device Framework

See Figure 2-1 for the dimension.

Figure 2-1

See Figure 2-2 for the device cable ports.

Figure 2-2

3Installation

Dome camera mainly uses ceiling installation; installation surface includes ceiling and wall.

Users can install the device with the installation position map and the screws in the

accessories bag.

Attention:

Please install the device in time after it is taken apart, which is to avoid the camera

module being exposed to damp environment for too long.

Before the installation, please make sure the installation surface is thick enough to

sustain at least 3X weight of the camera.

For the installation mode of side outlet, make sure the direction of side outlet is in

accordance with that of the installation position map when sticking the installation

position map. Besides, pull the cable through the pedestal cable slot before locking

the screw.

Figure 3-1

Note:

The installation figure is for reference only.

Step 1

Take out the installation position map from the accessories bag, and paste it on the ceiling or

wall according to the cable exit location, dig holes on the installation surface according to the

installation position map, take out the expansion bolts from the accessories bag and insert

them into the installation holes and fix them.

Step 2

Use the wrench to loosen the locking screw in the cover and take down the cover.

Step 3

Adjust the location of the dome pedestal according to the top cable outlet or side cable outlet.

Pull the cable out through the side outlet of installation surface and pedestal (please skip the

step if it is top cable outlet), aim the screw fixing holes of dome pedestal to the fixing holes of

expansion boles on the installation surface, then insert the self-tapping screws into the

expansion bolts and secure them firmly, fix the dome on the installation surface.

Step 4

Connect the video output port of the device cable to the back-end HAVR device and connect

the power port to power.

Step 5

Lens adjustment

You can adjust the lens zoom and focus on the back-end HAVR device to make image clear,

and then adjust the lens angle. Tighten the screws to fix the lens after it is adjusted to a proper

angle.

Step 6

Install the dome enclosure; install the enclosure which is taken down in step 2 back to the

dome pedestal.

So far you have completed device installation and cable connection, you can check device

monitoring image via back-end coding device.

4Menu

4.1 HAVR Settings

This HDAVS camera series can adjust OSD menu via coaxial control. After connected the

camera to the HDAVS series HAVR, from Main Menu->Setting->System->PTZ, you need to

select the channel number for access and set control mode as HDAVS and the protocol as

ICR-SD1. Click “Save” button to save current setup. See Figure 4-1.

Figure 4-1

4.2 Menu Operation

Click the right mouse button and select “PTZ Control”, then you will see the “PTZ Setup” menu,

which is as shown in Figure 4-2 and Figure 4-3.

Figure 4-2

Figure 4-3

See Sheet 4-1 for the details of button functions.

Button

Function

Open menu

、Select menu item

、Select menu value

Adjust lens zoom and auto

trigger focus Note:

Some of the buttons can only

be applied for the motorized

vari-focal camera.

Adjust lens focus

Auto focus under current

zoom rate

Lens reset

Sheet 4-1

If there is “ ”, click the “Confirm” button in “Menu Operation” interface to go to the 2nd menu.

Click “Return” button to go back to the previous menu interface.

Table des matières

Autres manuels ICRealtime Caméra de sécurité

ICRealtime

ICRealtime ICR-100X Manuel utilisateur

ICRealtime

ICRealtime ICIP-3000CCD-W Manuel utilisateur

ICRealtime

ICRealtime HD Pinhole Manuel utilisateur

ICRealtime

ICRealtime HD-AVS Manuel utilisateur

ICRealtime

ICRealtime ICIP-D2000-IR-B Manuel utilisateur

ICRealtime

ICRealtime AVS-4MB4012-IR Manuel utilisateur

ICRealtime

ICRealtime EL-3000N Manuel utilisateur

ICRealtime

ICRealtime ICIP D3000AVIR-M Manuel utilisateur

ICRealtime

ICRealtime ICIP360L6 Manuel utilisateur

ICRealtime

ICRealtime HD-PTZ-12X-W Manuel utilisateur

ICRealtime

ICRealtime AVS-4MB4016-IR Manuel utilisateur

ICRealtime

ICRealtime Elite IPEL-E80F-IRB2 Manuel utilisateur

ICRealtime

ICRealtime ICIPS1300WDR Manuel utilisateur

ICRealtime

ICRealtime AVS-D2110 Manuel utilisateur

ICRealtime

ICRealtime Elite Series Manuel utilisateur

ICRealtime

ICRealtime F Series Manuel utilisateur

ICRealtime

ICRealtime F Series Manuel utilisateur

ICRealtime

ICRealtime AVS-4KD8021-IR Manuel utilisateur

ICRealtime

ICRealtime IPEL-B2012X-IRW1 Manuel utilisateur

ICRealtime

ICRealtime IPMX-E20F-IRB1 Manuel utilisateur

ICRealtime

ICRealtime ICIP-B2000 Manuel utilisateur

ICRealtime

ICRealtime AVS-B2100 Manuel utilisateur

ICRealtime

ICRealtime Full HD(HD-SDI) CCTV Box Camera Manuel utilisateur

ICRealtime

ICRealtime ICIP-D1300 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur