ICP DAS USA M-7088 Manuel utilisateur

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7088

8-channel PWM Output and 8-channel High-

speed Counter Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7088

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

M-7088 has 8 PWM output channels and 8 counter inputs. It can be used to develop

powerful and cost effective analog control system. PWM (Pulse width modulation) is a

powerful technique for controlling analog circuits. It uses digital outputs to generate a

waveform with variant duty cycle and frequency to control analog circuits. It can be used

to Controlling the position/speed of motors, Dimming the brightness of lamps,

Controlling the speed of fans… etc.

2. Terminal Assignment

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the M-7051 module is:

Address = 01

Baud Rate = 9600

Checksum disabled

Data = 1 Start + 8 Data + 1 Stop (no parity)

PWM Frequency = 10 KHz

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PWM Duty Cycle = 50%

PWM Steps = 1 (Continuous Type)

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6. Configuration I/O module setting on PC

7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

Sub-function 04h of Function 46h, see user manual Section 3.3.2

Sub-function 06h of Function 46h, see user manual Section 3.3.4

Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

M-7088 8-ch PWM Output and 8-ch High-speed Counter DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

Table des matières

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA SG-785 Manuel utilisateur

ICP DAS USA

ICP DAS USA ZT-257 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-87004W Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3016 Manuel utilisateur

ICP DAS USA

ICP DAS USA PET-AR400 Manuel utilisateur

ICP DAS USA

ICP DAS USA MN-3253 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA FR-32R Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7060 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7188XA Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2050 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8213W-4G Manuel utilisateur

ICP DAS USA

ICP DAS USA MDC-700 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA ECAT-2012H Manuel utilisateur

ICP DAS USA

ICP DAS USA tDS-700-T Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8088W Manuel utilisateur

ICP DAS USA

ICP DAS USA tSG-3781B Manuel utilisateur

ICP DAS USA

ICP DAS USA XP-8000-Atom-CE6 Manuel utilisateur

ICP DAS USA

ICP DAS USA PET-7053 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8094 Manuel de la liste des pièces

ICP DAS USA

ICP DAS USA M-7051 Manuel utilisateur

ICP DAS USA

ICP DAS USA M-7067D Manuel utilisateur

ICP DAS USA

ICP DAS USA PROFIBUS PROFI-2510 Manuel utilisateur

ICP DAS USA

ICP DAS USA iDaSer-9000 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur