IBM AS/400e 270 Manuel utilisateur
AS/400e 270 or 820
Upgrading the System Unit from
Operations Console to Twinaxial
Console (5540)
Ve r s i o n 4
SENG-5540-00
AS/400e 270 or 820
Upgrading the System Unit from
Operations Console to Twinaxial
Console (5540)
Ve r s i o n 4
SENG-5540-00
Note
Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on
page iii and the “Notices” on page 23.
First Edition (July 2000)
This edition applies only to reduced instructions set computer (RISC) systems.
© Copyright International Business Machines Corporation 2000. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Safety and Environmental Notices
Danger Notices
A danger notice calls attention to a situation that is potentially lethal or extremely
hazardous to people.
DANGER
To prevent a possible electrical shock during an electrical storm, do not
connect or disconnect cables or station protectors for communications lines,
display stations, printers, or telephones. (RSFTD003)
DANGER
To prevent a possible electrical shock from touching two surfaces with
different electrical grounds, use one hand, when possible, to connect or
disconnect signal cables. (RSFTD004)
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage
on metal parts of the system or the products that attach to the system. It is the
customer’s responsibility to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock. (RSFTD201)
DANGER
To prevent a possible electrical shock when adding or removing any devices
to or from the system, ensure that the power cords for those devices are
unplugged before the signal cables are connected or disconnected. If possible,
disconnect all power cords from the existing system before you add or
remove a device. (RSFTD203)
Caution Notices
A caution notice calls attention to a situation that is potentially hazardous to
people because of some existing condition.
CAUTION:
Telecommunications Statement: This unit contains over-voltage circuits between
the ac power outlet and the unit. These circuits meet the standard limits
described in International Electrical Commission (IEC) 664, installation category
II. It is the customer’s responsibility to ensure that the power outlet meets the
standards of IEC 664, installation category II. (RSFTC214)
Laser Safety Information
CAUTION:
This product may contain a CD-ROM which is a class 1 laser product.
(RSFTC240)
© Copyright IBM Corp. 2000 iii
Product Recycling and Disposal
Components of the system, such as structural parts and circuit cards, can be
recycled where recycling facilities exist. IBM does not currently collect and recycle
used IBM products from customers in the United States other than those products
that are involved in trade-in programs. Companies are available to disassemble,
reutilize, recycle, or dispose of electronic products. Contact an IBM account
representative for more information.
The system unit contains batteries and circuit boards with lead solder. Before you
dispose of this unit, these batteries and circuit boards must be removed and
discarded according to local regulations or recycled where facilities exist. This book
contains specific information on each battery type where applicable.
Battery Return Program
In the United States, IBM has established a collection process for reuse, recycling,
or proper disposal of used IBM batteries and battery packs. For information on
proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.
Please have the IBM part number that is listed on the battery available when you
make your call. For information on battery disposal outside the United States,
contact your local waste disposal facility.
Environmental Design
The environmental efforts that have gone into the design of the system signify
IBM’s commitment to improve the quality of its products and processes. Some of
these accomplishments include the elimination of the use of Class I
ozone-depleting chemicals in the manufacturing process, reductions in
manufacturing wastes, and increased product energy efficiency. For more
information, contact an IBM account representative.
iv AS/400e 270 or 820: Upgrading the System Unit from Operations Console to Twinaxial Console (5540)
Before you begin
These instructions contain steps on how to upgrade the AS/400 system unit from
an Operations console to a Twinaxial console. The feature number is 4746 and the
customer card indentification number is 2746.
Before you begin
This feature is customer-installable. You can elect not to do this installation
yourself. Contact IBM or an Authorized Dealer to make arrangements for them to
perform the feature installation for a fee.
You need to allow additional time to complete your jobs, back up your system,
initial program load (IPL) your system, and verify your hardware configuration.
When you use these instructions, you may do some of the following:
vRemove the system unit covers.
vInstall your new hardware.
vInstall covers.
vIPL your operating system.
vVerify your new hardware configuration.
Some of the pictures in these instructions may not look exactly like the system unit
that you have. However, the steps to perform the task are the same.
__ 1. Ensure that you have a current backup of your system (including operating
systems, licensed programs, and data).
__ 2. Ensure that you take a few minutes to become familiar with these
instructions.
__ 3. If there are incorrect, missing or visibly damaged parts, contact one of the
following:
vYour authorized dealer
vIBM Rochester Manufacturing Automated Information Line (R-MAIL)
–1-800-300-8751 (United States)
–1-507-253-5242 (worldwide)
__ 4. If you encounter difficulties during the installation, contact your authorized
service provider or your authorized dealer.
__ 5. Determine if there are any existing prerequisites before you install your new
feature. Go to this Web site and locate your feature number and OS/400
release and check the prerequisites.
http://as400service.ibm.com/s_dir/slkbase.NSF/
Then do the following to get to the Customer Install Features Prerequisites:
a. Select All Documents
b. Select Collapse
c. Select General Information
d. Select Offerings
e. Select Feature Prerequisites
f. Select Customer Install Features Prerequisites
© Copyright IBM Corp. 2000 1
Powering off the system unit
__ 1. Ensure that all jobs are complete.
__ 2. When all jobs are complete, type pwrdwnsys *immed on an AS/400 command
line and press Enter.
Note: Should you encounter difficulties during the installation, contact your
authorized dealer or service provider.
__ 3. When the AS/400 is completely powered down, power off all PCs and
devices, such as printers and displays, that are connected to the system unit.
__ 4. Unplug any power cords, such as printers and displays, from electrical
outlets.
__ 5. Unplug the system unit power cord and any attached expansion unit power
cords from the electrical outlet.
__ 6. Refer to “Removing the back and side cover”on page 11 to remove the
system unit covers.
__ 7. Attach the disposable wrist strap to prevent electrostatic discharge from
damaging a device. Attach the adhesive part of the foil to an unpainted
surface.
Notes:
a. Follow the same precautions you would use without the wrist strap. The
2209 Disposable Wrist Strap is for static control. It will not increase nor
decrease your risk of receiving electric shock when using or working on
electrical equipment.
b. Discard the wrist strap immediately and contact your dealer for a
replacement, if the disposable wrist strap appears damaged or cut off.
Do not continue until a new wrist strap is available.
c. Remove the liner from the copper foil at the end, when you unroll the
strap.
d. Attach the copper foil to an exposed, unpainted metal surface on the
frame of the system unit (electrical ground).
Installing the 2746 communications adapter card
__ 1. DANGER
To prevent a possible electrical shock from touching two surfaces with
different electrical grounds, use one hand, when possible, to connect
or disconnect signal cables. (RSFTD004)
Disconnect the Operations Console cable connected to port 0 (left
connector) on the 2745 card in one of the following positions:
v270 System Unit, position C07. See “Configuration tables”on page 13 for
more information.
v820 System Unit, position C06. See “Configuration tables”on page 13 for
more information.
2AS/400e 270 or 820: Upgrading the System Unit from Operations Console to Twinaxial Console (5540)
Notes:
a. If the electronic customer support cable connects to port 1 (right
connector) on the 2745 card, remove it. The electronic customer support
cable installs into port 0 (left connector) on the 2745 card. Port 1 (right
connector) is available as a communications port.
b. Be sure to label the cables with the correct location (for example, slot
C06/port 0).
__ 2. Is there a card, other than the 2746 card, installed in position C05 —270
System Unit or C03 first or C11 second—820 System Unit?
No Yes
↓
Before you remove the card from the system unit, you need to see if
you have an open position to install the card you removed in a
different position.
Look at the PCI card area. Are there any open positions?
Yes No
↓
Use the following to help determine card placement.
vUse the card placement tool available on the Internet at:
http://www.ibm.com/as400/cif
vGo to the PCI Card Installation Instructions available on the
Internet at:
http://www.as400.ibm.com/tstudio/tech_ref/cif/index.htm
or the Installation and Service Library CD, SK3T-4028
vContact your authorized service provider or your
authorized dealer
Go to “Moving a card already in your unit”on page 15.
__ 3. Attention: Adapter cards are fragile; use static strap when handling,
handle only by the edges, and keep fingers off printed circuit area.
__ 4. Install the new 2746 communications adapter card in one of the following
positions:
v270 System Unit: C05
v820 System Unit: C03 –first or C11 –second
Before you begin 3
__ 5. Does your unit have screws to secure the cards?
No Yes
↓
__ a. Remove the screw from the card position where you plan to
install the card.
__ b. Go to step 8 on page 6.
__ 6. Your unit has card latches to secure the cards.
__ 7. Open the latch at the card position where you plan to install the card. Move
the blue latch counter clockwise and then swing the black latch out.
4AS/400e 270 or 820: Upgrading the System Unit from Operations Console to Twinaxial Console (5540)
Autres manuels pour AS/400e 270
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels IBM Matériel informatique
IBM
IBM 9332 Manuel utilisateur
IBM
IBM QuickOn for Running Windows Manuel utilisateur
IBM
IBM PN 10K8798 Manuel utilisateur
IBM
IBM S922 Mode d’emploi
IBM
IBM 4767 Manuel utilisateur
IBM
IBM ATA 133 Manuel utilisateur
IBM
IBM 3301690 Manuel utilisateur
IBM
IBM 7133 D40 Manuel utilisateur
IBM
IBM WebSphere DataPower XC10 Manuel utilisateur
IBM
IBM SA23-1325-01 Mode d’emploi
IBM
IBM p5 550 Guide d'installation
IBM
IBM eserver 7210 Manuel
IBM
IBM THINKCENTER 8128 Manuel du propriétaire
IBM
IBM MPC603EC Manuel utilisateur
IBM
IBM 55PUS8118 SCSI-2 Manuel utilisateur
IBM
IBM Power Systems 8247-42L Manuel utilisateur
IBM
IBM 9040-MR9 Manuel utilisateur
IBM
IBM Advanced SerialRAID/X Manuel utilisateur
IBM
IBM eserver Cluster 1350 Instructions d'installation et d'entretien
IBM
IBM SAN Volume Controller 2145-CF8 Manuel
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
