Hyundai Sonata CS-HY1120 Manuel utilisateur

Multi-Media Navigation System Installation Guide Rev A

Installation Guide

NOTICE OF INTENDED INSTALLATION AND USE

THE CARSHOW MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH

IS NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE.

THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS

WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.

IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION

OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO

VIOLATE STATE AND/OR FEDERAL LAW.

CARSHOW DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY DAMAGE THAT MAY

RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE.

STOP

Damage to the vehicle may occur

Do not proceed until process has been completed

CAUTION

Process must be carefully observed in order to reduce

the risk of damage to the accessory or vehicle

CRITICAL

Process must be carefully observed in order to ensure a

quality installation

TOOLS and EQUIPMENT

Specific tools and equipment recommended for this

process

SAFETY RISK

Observe safe practices, this process can be dangerous

and there is a risk of personal injury

TESTING and TROUBLESHOOTING

Content specific testing and troubleshooting points

CS-HY1120 Hyundai Sonata Installation Guide

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 2

PREPARING FOR THE INSTALLATION

Before you start, please read these critical steps below STEP

BEFORE YOU START THE

INSTALLATION,

READ THIS GUIDE!

CHECK THE BATTERY

Test the battery voltage to make sure it’s fully charged to

a minimum of 12.8 VDC

This only takes seconds and can save hours of

troubleshooting later.

TURN THE VEHICLE

OFF

Keep the Vehicle Off during the installation to avoid

setting various Vehicle Fault sensors

Keep the Vehicle OFF during the

installation

Failure to follow this may cause the AIRBAG FAULT

SENSOR to become enabled. Dealer Service

Departments charge a significant fee to reset the Fault

Sensor.

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 3

REMOVE THE FACTORY RADIO

You will need to remove multiple interior trim components prior to removing the factory radio.

The following steps will help guide you through this process.

STEP

Remove Lower Right Dash Trim

Carefully remove lower right side dash trim

Remove Lower Left Dash Trim

Carefully remove lower left side dash trim

Remove Phillips Screws

Carefully remove 2 x phillips (1-left & 1-right)screws to

release dash

Remove Radio Dash Trim

Carefully remove radio dash trim. Be sure to use proper

equipment and carefully pry on instructed area.

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 4

Remove Radio Dash Trim

Carefully remove radio dash trim. Be sure to use proper

equipment and carefully pry on instructed area.

Remove Radio Dash Trim

Carefully remove radio dash trim. Be sure to use proper

equipment and carefully pry on instructed area.

Remove Radio Dash Trim

Carefully remove radio dash trim. Be sure to use proper

equipment and carefully pry on instructed area.

Remove Radio Mounting Screws

Carefully remove 4 x phillips radio mounting screws

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 5

LOCATING REMOTE COMPONENTS

You will need to mount the GPS and Optional Satellite Radio Antennas on the exterior of the vehicle.

And mount the iPod Interface Connector in the vehicle. The following steps will help guide you

through this process.

STEP

Use Caution around SRS Components

It is the installer’s responsibility to ensure that the safety

equipment in the vehicle is NOT adversely affected by

installation of this system. Ensure that the routing of the

harnesses do NOT obstruct airbags, SRS or other safety

devices.

Mount the GPS and Sat Radio antenna in

a location on the exterior of the Vehicle

Route the GPS harness away from other power harnesses in

the vehicle.

This will help to ensure optimum performance of the GPS

system.

“OPTIONAL”

Install the iPod interface connector in a

location accessible to the end-user

Locate the iPod interface module in an area which can be

serviced in the future.

The iPod cable is intended to be a serviceable item, which

plugs into the iPod/Sat radio Interface Module.

INSTALL THE CARSHOW NAVIGATION SYSTEM

You will need to prepare the CarShow Navigation System for installation in the vehicle. STEP

Remove the DVD Transport Screws

There are 2 x Phillips Transport Screws which protect the DVD

Mechanism during transportation.

Transport Screws must be removed prior to installation.

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 6

Connect the Power and GPS Harnesses

The GPS Harness must be tightened with a WRENCH to

ensure it is properly seated.

Be sure to use white cable clamp to secure GPS antenna cable

Failure to follow this step may result in poor GPS signal

Connect Optional Harnesses such as

iPod, Satellite Radio, Camera, Reverse

Sensors

These harnesses must be fully engaged prior to the system

installation.

See the Harness Diagrams for more information

Prepare the Vehicle side harnesses for

connection to the CarShow Harness

Use care not to pinch or damage cables as this will cause

performance issues/failures

CAUTION

Remove OEM Hazard Switch

Carefully remove OEM Hazard switch and relocate into

CarShow Dash Bezel

Remove OEM Climate Controls

Carefully remove OEM climate controls and relocate into

CarShow Dash Bezel

OEM Dash Bezel

OEM Dash Bezel shown at right with all OEM switches

removed

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 7

CarShow dash Bezel

CarShow Dash Bezel shown at right with all OEM

switches installed

Important Connections Part 1 of 9

Connect Passenger airbag/Seatbelt display into supplied

CarShow T-Harness shown at right.

(If not plugged in when starting vehicle, this might cause

error code.)

Important Connections Part 2 of 9

Connect Proper end of CarShow T-Harness into OEM

Airbag/Seatbelt display

(If not plugged in when starting vehicle, this might cause

error code.)

Important Connections Part 3 of 9

Locate supplied foam wrap

Important Connections Part 4 of 9

Carefully wrap OEM Airbag/Seatbelt display with

supplied foam

Important Connections Part 5 of 9

Peel back only enough white backing to adhere foam

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 8

Important Connections Part 6 of 9

Finished wrap shown at right

Important Connections Part 7 of 9

Carefully put airbag/seatbelt display into dash cavity

below passenger side ac vent.

Airbag/Seat display shown in BLUE at right

Important Connections Part 8 of 9

Connect proper harness to vehicle side of

airbag/seatbelt display connector

Important Connections Part 9 of 9

Connect proper connector from CarShow T-harness to

airbag/seatbelt indicator as shown at right

Install CarShow Unit

Install CarShow unit into dash and be sure to re-install all

mounting screws that were removed.

Install CarShow Dash

Install CarShow dash and be sure to connect all

harnesses

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 9

Install Complete

CarShow dash bezel shown installed at right

Turn the vehicle ON and confirm the unit

is fully operational

With the connectors Fully Engaged, turn the vehicle on

and press the RESET for 5 seconds on the unit.

Turn the vehicle ON and test OEM

Features

Test Emergency Lights, AC controls, and Passenger

Airbag/Seatbelt Display.

Insert a DVD to confirm the Video Disable

Circuit is properly Operating.

The Brake Wire must be connected to the Park Brake

Indicator Wire to complete a ground when the brake is

engaged.

RE-INSTALL THE TRIM COMPONENTS

You will need to reinstall all trim components

STEP

Re-install Lower Left/Right Dash Trim

Carefully re-install lower left/right side dash trim

CAUTION

CarShow Installation Guide

Installation Guide CS-HY1124 Rev A

Page 10

ENABLE INSTALLER SETTINGS

You will need to select certain Installer Setting based on any Optional Equipment that you may have

installed

STEP

Launch the Installer Setting Screen

From any screen with the Menu Button, follow these

steps to display the Installer Setting Screen, select:

1) From any Screen, select “Menu”

2) From the Menu Screen, select “Settings”

3) Press “Keypad,” Press “7253” and “Enter”

Select the individual Settings as needed

for the installed components

Selectable options vary by product and installation.

Select the options as applicable for the installed optional

components.

Perform Pre-Delivery Tests

You will need to perform several Pre-Delivery Tests to ensure customer satisfaction

Some optional equipment may not be applicable

STEP

Turn the vehicle ON and System ON

Confirm the unit starts up properly

Troubleshooting

1) Reset the System while the Vehicle is ON

2) Confirm all connectors are properly installed

3) Check the Vehicle and System Fuses

Select RADIO as the Source

Confirm that the AM and FM reception are as expected

Troubleshooting

1) Confirm Antenna is properly connected.

2) Reset the System

Table des matières

Autres manuels Hyundai Système de navigation automobile

Hyundai

Hyundai AV2B4SDAN Manuel utilisateur

Hyundai

Hyundai TQ8-AN240DKAN Manuel utilisateur

Hyundai

Hyundai Santa Fe Manuel utilisateur

Hyundai

Hyundai AN243DKAN Manuel utilisateur

Hyundai

Hyundai DIGITAL NAVIGATION SYSTEM Manuel utilisateur

Hyundai

Hyundai AVANTE MTXM100AD Manuel utilisateur

Hyundai

Hyundai Santa Fe 2016 Manuel utilisateur

Hyundai

Hyundai ELANTRA Manuel utilisateur

Hyundai

Hyundai Veloster 2012 Manuel utilisateur

Hyundai

Hyundai AVN-700MDA Manuel utilisateur

Hyundai

Hyundai LAN1100EHVF Manuel utilisateur

Hyundai

Hyundai IONIQ Hybrid 2018 Manuel utilisateur

Hyundai

Hyundai BlueLink Manuel utilisateur

Hyundai

Hyundai blueLink AN241HGAN Manuel utilisateur

Hyundai

Hyundai Gen5W Manuel utilisateur

Hyundai

Hyundai PONTUS Manuel utilisateur

Hyundai

Hyundai SONATA Manuel utilisateur

Hyundai

Hyundai Veloster Manuel utilisateur

Hyundai

Hyundai IONIQ ELECTRIC Fiche technique

Hyundai

Hyundai IX35 Manuel utilisateur

Hyundai

Hyundai LAN8921EHCM Manuel utilisateur

Hyundai

Hyundai TUSON Manuel utilisateur

Hyundai

Hyundai 2011 EQUUS Instructions de montage

Hyundai

Hyundai LAN1050EHGD Manuel utilisateur

Manuels Système de navigation automobile populaires d'autres marques

Clarion

Clarion Navigation In-Car Entertainment Manuel utilisateur

Rosen

Rosen DP-1001 Manuel utilisateur

Alpine

Alpine INE-W970HD Manuel utilisateur

Skoda

Skoda AMUNDSEN+ Manuel utilisateur

Blaupunkt

Blaupunkt TravelPilot DX-N Manuel utilisateur

Pioneer

Pioneer MZ360500EX Manuel utilisateur

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Manuel utilisateur

Kenwood

Kenwood DNN991HD Manuel utilisateur

AvMap

AvMap Geosat 2C Manuel utilisateur

Eonon

Eonon GE01B Manuel utilisateur

Pioneer

Pioneer AVIC-Z920DAB Manuel utilisateur

Nextar

Nextar M3-MX - Automotive GPS Receiver Manuel utilisateur

Furrion

Furrion NV2200 Manuel utilisateur

Mio

Mio MOOV 200-Series Manuel utilisateur

Prestigio

Prestigio GeoVision 5150 Manuel utilisateur

Hummer

Hummer 2006 H3 Manuel utilisateur

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Guide de configuration

Garmin

Garmin StreetPilot c510 Manuel utilisateur