Hyundai Excel 1993 Guide d'installation
HYUNDAI
1993
Shop Manual
Volume 1 & 2
FOREWORD
This shop manual is intended for use by service techni-
cians of authorized Hyundai dealers to help them provide
efficient and correct service and maintenance on Hyundai
vehicle.
All the contents of this manual, including drawings and
specifications, are the latest available at the time of
publication. However, specifications and procedures are
subject to change without any notice.
As for the modifications affecting service performance,
dealers shall be provided technical service bulletins or
supplementary volumes.
This book may not be reproduced or copied, as a whole
or as a part, without the written permission of publisher.
JULY 1992. Printed in Korea
NOTE : This PDF Manual contains the contents of
both printed Volumes 1 & 2.
CONTENTS
TITLE
GENERAL INFORMATION
LUBRICATION AND MAINTENANCE
ENGINE MECHANICAL
COOLING SYSTEM
ENGINE ELECTRICAL SYSTEM
INTAKE & EXHAUST SYSTEM
EMISSION CONTROL SYSTEM
FUEL SYSTEM
CLUTCH (Hydraulic type)
CLUTCH (Cable type)
MANUAL TRANSAXLE
AUTOMATIC TRANSAXLE [KM176]
AUTOMATIC TRANSAXLE [KM171]
DRIVE SHAFT AND FRONT AXLE
FRONT SUSPENSION
REAR SUSPENSION
STEERING SYSTEM (Manual & Power)
BRAKE SYSTEM
BODY (INTERIOR AND EXTERIOR)
BODY ELECTRICAL SYSTEM
AIR CONDITIONING SYSTEM
APPENDIX (Electrical Wiring System)
SECTION
00
10
20
25
27
28
29
31
41
41A
43
45
45D
49
54
55
56
58
60
90
97
WS
GENERAL
INFORMATION
00-2
GENERAL INFORMATION
HOW TO USE THIS MANUAL
This manual is divided into 23 sections. This first page of each
section is marked with a black tab at the edge of the page. You can
quickly find the first page of each section without looking through
a full table of contents.
Each section includes the essential removal, installation, adjust-
ment and maintenance procedures for servicing all body styles.
This information is current as of time of publication.
An INDEX is provided on the first page of each section to guide you
to the item to be replaced.
TROUBLESHOOTING tables are included for each system to help
you diagnose the system problem and find the cause. The repair for
each possible cause is referenced in the remedy column to quickly
lead you to the solution.
DEFINITION OF TERMS
Standard Value
Indicates the value use as the standard for judging the quality of
a part or assembly on inspection or the value to which the part
or assembly is corrected and adjusted. It is given by a tolerance.
Limit
Shows the standard for judging the quality of a part or assembly on
inspection and means the maximum or minimum value within which
the part or assembly must be kept functionally or in strength. It is
a value established outside the range of standard value.
NOTE, WARNING AND CAUTION
NOTE
A point of information.
WARNING
Information about an activity that could cause damage to the
vehicle.
CAUTION
Information about an activity that could cause injury or
damage to the driver, occupants or repair personnel.
ABBREVIATIONS
MPI: Indicates Multi Point Fuel Injection system.
FBC: Indicates Feedback Carburetor system.
VEHICLE IDENTIFICATION NUMBER
LOCATION
The vehicle identification number (V.I.N.) is stamped on the
upper right side of the cowl top front panel.
VEHICLE IDENTIFICATION NUMBER
KMH
V
F
3
2J9
M
U
000047
1. World manufacturer’s identifier code
KMH - Hyundai Motor Co., Korea
2. Drive line type
V - For LHD (EXCEL)
3. Body Type
F - 4 Door sedan
D - 3 Door sedan
4. Body style & version
1 - Standard
2 - Deluxe
3 - Super deluxe
5. Restraint type
1 - Active system
2 - Passive system
6. Engine type
J - 1468 cc
7. Check digit
Mathematically determined to validate frame numbers
8. Model year
R - 1994 P - 1993
9. Plant code
U - Ulsan plant
10. Serial number 000001 through 999999
00-4
TRANSAXLE NUMBER IDENTIFICATION
Description (Automatic transaxle)
1. Model
B: KM 176 A: KM 171
2. Product year
M : 1991
N : 1992
P : 1993
R : 1994
3. Final gear ratio
F : 4.062
E : 3.600
4. Classification of detail
A : Excel
5. Spare
D : Damper Spring type
6. Serial No.
ENGINE IDENTIFICATION PLATE
The engine identification plate is stamped at the right front side on
the top edge of the cylinder block.
ENGINE IDENTIFICATION NUMBER
Engine identification number consists of 10 digits.
1.
Engine fuel
G : Gasoline
2.
Engine range
4 : In line 4 cycle 4 cylinder
3.
Engine development order
A-Z :
4.
Engine capacity
J : 1468 cc
5.
Product year
6.
Engine production sequence number
000001 - 999999
00-6
PROTECTION OF THE VEHICLE
Always be sure to cover fenders, seats, and floor areas before
starting work.
CAUTION:
The support rod must be inserted into the hole near the edge
of the hood whenever you inspect the engine compartment to
prevent the hood from falling and possibly injuring you.
Assure that the support rod has been released prior to closing
the hood. Always double check to be sure the hood is firmly
latched before driving away.
A WORD ABOUT SAFETY
The following precautions must be followed when jacking up the
vehicle.
1. Block wheels.
2.
Use only specified jacking positions.
3.
Support vehicle with safety stands (jack stands)
Refer to the page 00-10.
4.
Start the engine only after making certain the engine com-
partment is clear of tools and people.
PREPARATION OF TOOLS AND MEASURING
EQUIPMENT
Be sure that all necessary tools and measuring equipment are
available before starting work activity.
SPECIAL TOOLS
Use special tools when they are required.
REMOVAL OF PARTS
First find the cause of trouble and then make sure whether
removing or disassembling is required before starting the job.
DISASSEMBLY
If the disassembly procedure is complex, requiring many parts to
be disassembled, all parts should be disassembled in a way that will
not affect their performance or external appearance and be iden-
tified so that reassembly can be performed efficiently.
1. Inspection of parts
Each part when removed should be carefully inspected for
wear, deformation, damage, and other problems.
2. Arrangement of parts
All disassembled parts should be carefully arranged for
reassembly.
Be sure to separate or otherwise identify the parts to be
replaced from those that will be reused.
00-8
3. Cleaning parts for reuse
All parts to be reused should be carefully and thoroughly
cleaned by the appropriated method.
PARTS
When replacing parts, use HYUNDAI genuine parts
REASSEMBLY
Standard values, such as torques and certain adjustments, must
be strictly observed in the reassembly of all parts.
If removed, these parts should be replaced with new ones.
1. Oil seals
2. Gaskets
3. O-rings
4. Lock washers
5. Cotter pins (split pins)
6. Nylon nuts
Depending on where they are;
1.
Sealant should be applied to gaskets.
2.
Oil should be applied to moving components of parts.
3.
Specified oil or grease should be applied at the prescribed
locations (oil seals, etc.) before assembly.
ADJUSTMENTS
Use gauges and testers to correct adjustments to standard values.
Table des matières
Autres manuels Hyundai Automobile
Hyundai
Hyundai Tucson 2017 Manuel utilisateur
Hyundai
Hyundai IONIQ 6 Manuel utilisateur
Hyundai
Hyundai Sonata Hybrid 2017 Manuel utilisateur
Hyundai
Hyundai Tiburon Manuel utilisateur
Hyundai
Hyundai 2005 Sonata Manuel utilisateur
Hyundai
Hyundai IONIQ ELECTRIC Manuel utilisateur
Hyundai
Hyundai Azera 2017 Manuel utilisateur
Hyundai
Hyundai Matrix 2003 Manuel utilisateur
Hyundai
Hyundai Tucson 2017 Manuel utilisateur
Hyundai
Hyundai i40 Saloon 2012 Manuel utilisateur
Hyundai
Hyundai TUCSON 2018 Manuel utilisateur
Hyundai
Hyundai EQUUS 2016 Manuel utilisateur
Hyundai
Hyundai Tucson Manuel utilisateur
Hyundai
Hyundai VENUE Manuel utilisateur
Hyundai
Hyundai SANTA FE 2018 Manuel utilisateur
Hyundai
Hyundai i30 2013 Manuel utilisateur
Hyundai
Hyundai 2013 Azera Manuel utilisateur
Hyundai
Hyundai Sonata 2015 Manuel utilisateur
Hyundai
Hyundai Tucson 2013 Manuel utilisateur
Hyundai
Hyundai SantaFe Manuel utilisateur
