HunterDouglas Vignette Traditional Manuel utilisateur
Installation •Operation •Care
Vignette®Modern Roman Shades
Traditional™Style Shades
PowerView™Motorization
CONTENTS
Getting Started:
Product View ................................................................ 1
Tools and Fasteners Needed .......................................... 2
Installation:
Installation Overview ..................................................... 3
STEP 1 — Install the Brackets....................................... 3
STEP 2 — Install the Shade .......................................... 7
STEP 3 — Connect the Power Source............................ 8
Attach Magnetic Hold-Down Brackets (Optional)............ 12
Operation:
Testing the Shade ....................................................... 13
Using the PowerView™Remote .................................... 14
Resetting the Shade.................................................... 15
Troubleshooting .......................................................... 16
Care:
Removing the Shade (If Necessary) .............................. 19
Cleaning Procedures ................................................... 19
Declarations ........................................Inside Back Cover
Warranty.........................................................Back Cover
Questions?
Call the Hunter Douglas Customer Information Center at
1-888-501-8364.
© 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
GETTING STARTED
1
Product View Battery
Wand
Battery
Wand Clips
Magnetic
Hold-Down
Brackets
(Optional)
Headrail
Installation
Brackets
Power Cable*
Extension Cable
Bottom Rail
Weight
Clips
Balance
Weight
Spacer
Blocks
*The power cable can be located at either end of the headrail, depending on the specified motor placement.
2
GETTING STARTED
Thank you for purchasing Hunter Douglas Vignette®Modern Roman Shades with PowerView™
Motorization. With proper installation, operation, and care, your new shades will provide years of
beauty and performance.
Please thoroughly review this instruction booklet and the enclosed packing list before beginning
the installation. For information regarding operation and programming, refer to the guide
included with your remote control.
Tools and Fasteners Needed
■Flat blade and Phillips screwdrivers
■Level (laser level is recommended)
■Measuring tape and pencil
■Power drill,
3
/
32
" drill bit, and
1
/
4
" hex driver
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■#6 Hex Head Screws (Provided). Two 1
1
/
2
" screws are provided per installation bracket.
■Longer Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long
enough for a secure attachment.
■Speed Nuts and Screws (Provided). Extension brackets are supplied with screws and
speed nuts.
■Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall.
Speed Nut
and Screw
(Two Provided with
Each Extension Bracket)
#6 x 1
1
/
2
"
Hex Head Screw
(Provided)
Longer #6 Hex Head Screw
for Use with Spacer Blocks
(Not Provided)
INSTALLATION
3
Installation Overview
To install your shade, you will need to perform the following three steps:
STEP 1: Install the Brackets
STEP 2: Install the Shade
STEP 3: Connect the Power Source
STEP 1 — Install the Brackets
■Your order will include the correct number of installation brackets for your shade width, as
shown in the table below.
■Shade orders will also include spacer blocks if needed for added clearance.
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the shade installation process
follows easily. To prepare for this important first step, review the mounting types and basic
window terminology illustrated below.
■Refer to the appropriate page below based on the mounting type chosen for your order:
➤Inside Mount — Page 4
➤Outside Mount — Page 5
➤End Mount — Page 6
Outside Mount
Shade mounts outside
window opening.
Inside Mount
Shade fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb
Shade
Width
Brackets
Required
12" –48" 2
48
1
/
8
" –84" 3
84
1
/
8
" –96" 4
Spacer Blocks
Installation Bracket
1
/
2
"
1
/
4
"
INSTALLATION
4
3"
Casement
Depth
3"
Casement
Depth
Mount the Installation Brackets — Inside Mount
■Measure and mark 3" in from each jamb for bracket location.
➤If more than two installation brackets came with your order, mark the location of the
additional bracket(s) spaced evenly between the two end brackets. Mount into wood
whenever possible. Allow a minimum of 18" from the motor side for the battery
wand.
■Center the brackets on yourmarks, then mark the screw hole locations.
➤The minimum casement depth for installation
brackets is 1" (1
3
/
8
" with battery wand). Mark the
rear set of installation bracketholes with shallow
mounting depths.
➤The minimum casement depth for a fully recessed
mount is 3
7
/
8
" (4
3
/
8
" with battery wand). Mark the
front set of bracket holes when depth permits.
IMPORTANT: For shades with a battery wand, allow
a minimum of
5
/
8
" clearance behind the brackets to
accommodate the wand.
■Drill the screw holes using a
3
/
32
" drill bit.
CAUTION: Use drywall anchors when mounting into drywall.
■Use a level to check that the mounting surface is level.
Shim the brackets if necessary.
■Attach the installation brackets using the screws
provided.
IMPORTANT: The front edges of the installation
brackets must align to each other.
Proceed to “STEP 2 — Install the Shade” on page7.
Jamb Jamb
Window Opening
Space Evenly Space Evenly3" 3"
INSTALLATION
5
Mount the Installation Brackets — Outside Mount
■Center the headrail over the window opening at the desired height. Use a pencil to lightly
mark each end of the headrail.
➤Alternatively, measure the width of the headrail and use that width to mark the headrail
end points over the window opening.
■Measure and mark 3" in from each end of the headrail.
➤If more than two installation brackets came with your order, mark the location of the
additional bracket(s) spaced evenly between the two end brackets. Mount into wood
whenever possible. Allow a minimum of 18" from the motor side for the battery
wand.
■Center the brackets on yourmarks, then mark the screw hole locations.
➤A minimum 1" flat vertical surface is required.
➤The top of the installation brackets should be at
the desired height. The brackets must be level
andaligned.
CAUTION: The rear of the brackets must be flush
against a flat mounting surface. Do not mount brackets
oncurved molding.
■Drill the screw holes using a
3
/
32
" drill bit.
CAUTION: Use drywall anchors when mounting into drywall.
■Attach the installation brackets using the screws provided.
IMPORTANT: If using a battery wand, use a minimum
of one
1
/
2
" and one
1
/
4
" spacer blocks per installation
bracket to provide the clearance required for the battery
wand. See the instructions on the following page.
3"
Window Opening
Space Evenly Space Evenly3" 3"
Headrail End Mark Headrail End Mark
3"
Spacer
Blocks
1
/
2
"
1
/
4
"
INSTALLATION
6
■If the shade will be powered by a battery wand: Attach the installation brackets with the
1
/
2
" and
1
/
4
" spacer blocks. Use 2" #6 hex head screws (not provided).
➤The solid side of the spacer blocks faces the
mounting surface.
➤If using additional spacer blocks for more
clearance, attach the installation brackets and
spacer blocks with #6 screws long enough for
a secure installation.
IMPORTANT: Do not add more than 1
1
/
2
" of
clearance using spacer blocks.
IMPORTANT: The tops of the installation brackets
must be level with the front edges aligned.
Proceed to “STEP 2 — Install the Shade” on page7.
Mount the Installation Brackets — End Mount
End mount the headrail when conventional
mounting techniques will not work — for example,
in an arched window opening.
■Mount extension brackets to each side of the
opening at the desired height of the shade.
➤The mounting surface must be vertical and
flat, not part of an arched curve.
➤Minimum mounting surface width with a
built-in battery wand is 2".
➤Minimum mounting surface width with a
satellite battery pack, C-size satellite battery
wand, or DC power supply is 1
1
/
2
".
■Attach the installation brackets to the extension
brackets using the provided screws and
speednuts.
Proceed to “STEP 2 — Install the Shade” on page7.
Spacer
Blocks
Longer
Screws
Mounting
Surface
Width
Extension
Bracket
Speed Nuts
Screws
Installation
Bracket
INSTALLATION
7
STEP 2 — Install the Shade
Mount the Headrail
CAUTION: Be sure the cables do not become pinched by the installation brackets when
mounting the headrail.
■Hold the headrail so the front (curvedside) faces you.
■Push the top edge of the headrail into the installation brackets.
■Rotate and push the headrail back until it snaps into place. You will hear a click when the
shade is securely installed.
WARNING: Failure to snap the headrail securely into the installation brackets may
cause the shade to release unexpectedly.
■Gently pull on the front of the headrail to ensure that the shade is locked into the brackets.
■Remove the plastic covering on the front of the headrail.
Headrail
Installation Bracket
Fabric Guard
INSTALLATION
8
STEP 3 — Connect the Power Source
NOTE: When power is connected to the motor, a green LED inside the manual control button
housing will flash to indicate the shade is ready for operation.
■Refer to the appropriate page based on the ordered power source.
➤For a battery wand, see below.
➤For a satellite battery pack, see page 9.
➤For an 18V DC power supply, see page10.
➤For an 18V DC power supply with daisy-chain connections, see page11.
➤For a C-size satellite battery wand or large DC power supply, see the instructions that
came with the unit.
If You Have a Battery Wand...
Install Batteries Into the Battery Wand
■Squeeze the cap latch to release thecap.
■Remove the cap from the battery wand.
■Install the batteries according to the
instructions on the battery wand label.
■Hunter Douglas recommends AA alkaline batteries for use with our battery-powered shades.
These will provide approximately one year of operation. Lithium and rechargeable batteries
are not recommended.
■Replace the cap.
➤Align the tab with the end of the wand.
➤Press the cap on until it latches.
Mount the Battery Wand into theBattery Wand Clips
■Align the battery wand with its
socket toward the motor
cartridge end cap on the shade.
■Push the battery wand straight up
into the battery wand clips until it
snaps into place. Check to make
sure the battery wand is secure.
CAUTION: Be sure the cables do not become pinched by the battery wand clips during
installation. Damage or overheating of components could result.
TabSlot
Cap
Latch
Battery Wand
Squeeze
Back of Shade
Socket
Table des matières
Autres manuels HunterDouglas Store vénitien
HunterDouglas
HunterDouglas LiteRise Manuel de la liste des pièces
HunterDouglas
HunterDouglas Skyline Manuel de la liste des pièces
HunterDouglas
HunterDouglas Alustra Woven Textures Manuel utilisateur
HunterDouglas
HunterDouglas Sonnette Manuel utilisateur
HunterDouglas
HunterDouglas Sonnette Manuel de la liste des pièces
HunterDouglas
HunterDouglas Reveal Manuel de la liste des pièces
HunterDouglas
HunterDouglas Reveal with MagnaView Manuel d'utilisation
HunterDouglas
HunterDouglas Duette Manuel utilisateur
HunterDouglas
HunterDouglas Solera Soft Shades Manuel utilisateur
HunterDouglas
HunterDouglas Wood Blinds Manuel utilisateur
HunterDouglas
HunterDouglas DecoFlex WireFree Telis Mode d'emploi
HunterDouglas
HunterDouglas Blockout Manuel utilisateur
HunterDouglas
HunterDouglas Decor Standard Cordlock Manuel du propriétaire
HunterDouglas
HunterDouglas Standard Hardware System Manuel de la liste des pièces
HunterDouglas
HunterDouglas Specialty Motorized Vertical Blinds Manuel de la liste des pièces
HunterDouglas
HunterDouglas RB 500 Guide de sécurité
HunterDouglas
HunterDouglas RB 500 Guide de sécurité
HunterDouglas
HunterDouglas PowerView Gen 3 Manuel utilisateur
HunterDouglas
HunterDouglas Country Woods Manuel d'utilisation
HunterDouglas
HunterDouglas EverWood Guide de l'utilisateur
Manuels Store vénitien populaires d'autres marques
Domondo
Domondo PureNight Manuel d'instructions d'installation
rollease acmeda
rollease acmeda Easy Spring Air Guide de configuration
IKEA
IKEA KADRILJ Manuel utilisateur
Hallis Hudson
Hallis Hudson Rolls Super glide Manuel utilisateur
Benthin
Benthin P1614 Manuel utilisateur
MV LINE
MV LINE CLARA 015 Mode d’emploi
