Huawei OptiX OSN 3500 Manuel utilisateur

HUAWEI TECHNOLOGIES CO., LTD.

OptiX OSN 3500

Quick Installation Guide

Issue: 21

Date: 2019-01-28

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees

or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute a warranty of any kind, express or implied.

Installation Process

Before You Start PrecautionsPage 1

Start

Instructions and

Precautions for

Handling Boards

Page 4

Installing and

Routing Cables

Pages

25 to 62

Installing and

Routing Fibers

Pages

62 to 65

Installing Orderwire

Phones

Page 66

Checking the

Installation

Pages

67 to 68

Checking Fiber

Attenuation

Page 69

Engineering Labels

Pages

70 to 73

Assembling Cable

Connectors

Pages

74 to 76

End

Installing and

Routing Power

Cables and PGND

Cables

Pages

26 to 44

Cable Holes on the

Top and at the

Bottom of the N63E

Cabinet

Page 25

Installing and

Routing Alarm

Cables

Page 46

Installing and

Routing

Cabinet Indicator

Cables

Page 45

Installing and

Routing

E3/T3/E4/STM-1

Cables

Pages

50 to 52

Installing and

Routing E1/T1

Cables

Pages

47 to 50

Installing and

Routing IF Cables

Pages

54 to 57

Installing and

Routing Ethernet

Cables

Pages

52 to 54

Installing and

Routing Network

Management

Cables

Page 59

Installing and

Routing External

Clock Cables

Pages

58 to 59

Installing and

Routing Cables for

PCM Boards

Page 61

Installing and

Routing SDI Coaxial

Cables

Page 60

Installing Cable

Distribution Plates

Page 13

Installing Fiber

Management Trays

Pages

13 to 14

Installing the

SS61COA

Pages

15 to 17

Installing the

SS62COA

Pages

18 to 19

Tools for InstallationPage 2

CablesPage 3

Introduction to the

OptiX OSN 3500

Equipment

Pages

5 to 6

Installing

Components

Pages

7 to 24

Installation HolesPage 7

Installing the RPC

Frame

Pages

20 to 21

Installing and

Routing External

Fibers

Pages

62 to 64

Installing and

Routing Internal

Fibers

Pages

64 to 65

Installing and

Routing Cables for

the Extended

Subrack

Page 62

Installing the

Subrack

Page 8

Checking the Power

Jumpers on the

Board

Pages

9 to 12

Installing the DCMPage 22

Installing the UPM

Power System

Pages

23 to 24

Precautions

This document provides quick guidelines for hardware installation.

This document does not describe pre-delivery assembly. This document describes only procedures for

onsite installation.

Electrostatic Discharge

Wear ESD gloves or an ESD wrist strap prior to contact with the

equipment or before handling the plug-boards, boards, and IC

chips to prevent damage to sensitive components caused by

electrostaticdischarge from the human body. Ensure that the

other end of the ESD wrist strap is properly grounded.

Binding Cables

Binding intervals between cable ties or optical fiber binding straps inside the cabinet cannot exceed 250 mm.

(The distance cannot exceed 200 mm for user cables).

Binding intervals between cable ties for all cables and corrugated tubes outside the cabinet are determined

according to the distance between the two horizontal beams. If the cable trough does not contain any beams,

the binding intervals between cable ties cannot exceed 250 mm.

Checking Before Installation

Check the telecommunications room, cabinet, power supply, ground cables, optical cables, and

associatedfacilities prior to installation. Start the installation according to the engineering design

documents after confirming that conditions are met.

NOTE

CAUTION

Tools for Installation

Long measuring tape Phillips screwdriver Flat-head screwdriver

Adjustable wrench Heat gun

COAX crimping tool Wire clippers Wire stripper

Cold press pliers Network cable tester Multimeter

COAX stripper RJ45 crimping tool Diagonal pliers

Utility knife

Cables

BGND power cable

Power cable for the OptiX OSN 3500 III

subrack Power cable for the general subrack

75-ohm 8xE1 cable 120-ohm 8xE1 cable–48 V DC power cable

75/120-ohm clock transit cable (1) 75/120-ohm clock transit cable (2) 75-ohm clock cable

Alarm output and input cable Alarm cascading cable between subracks COA cascading serial port cable

COA serial port cable COA power cable

120-ohm 16xE1 cable PGND cable

SDI coaxial cable

Instructions and Precautions for Handling Boards

Do not hold a board without hand protection. Wear an ESD wrist strap or ESD gloves before handling a board.

Insert filler panels into vacant slots on an NE to prevent foreign matters from getting into the NE, which may

result in faults on the NE.

Boards are fragile and valuable. When handling or placing a board, exercise caution and put it into a

dedicated packing box.

Holding a board without hand protectionWearing ESD gloves Wearing an ESD strap

Hold the front panel of a board with hands.

CAUTION

N1PIUB

Introduction to the OptiX OSN 3500 Equipment

Front View

Exterior of the OptiX OSN 3500 III Subrack

Side View

b Oblique View

Bolt for the PGND

cable

ESD jack Fan

Cable trough Air filter

Front view of the

N1PIUB

Label for the OptiX OSN 3500 III

subrack

Exterior of the General and Enhanced OptiX OSN 3500 Subracks

Front View

Side View

b Oblique View

N1PIU\N1PIUA

The exterior of the enhanced OptiX OSN 3500 subrack (1100 W) is the same as that of the general OptiX

OSN 3500 subrack. The N1PIU power board is used for the general OptiX OSN 3500 subrack, and the

N1PIUA power board is used for the enhanced OptiX OSN 3500 subrack (1100 W).

NOTE

OSN 3500 11, 13, 20, and 22

39 and 40

OSN 3500 46, 48, 55, and 57

74 and 75

78 and 82

Cable distribution

plate

PDU

Installing Components

Positions of the Installation Holes

Cable distribution

plate

•Front view of the cabinet

•Positions of the installation holes

Structural

Component

Position of the

Installation Hole Remarks

The fan and air filter

are installed in the

subrack.

The fan and air

filter are installed

in the subrack.

Remove the front door and side panels of the cabinet before

routing cables. For information about how to remove the

doors, see the N63E Cabinet Installation Guide. To ensure

safe operations, assign a minimum of two persons to install

the subrack.

First install subracks in the lower part and then in the upper

part of a cabinet. If there is only one subrack, install it in the

lower part of the cabinet.

NOTE

Autres manuels pour OptiX OSN 3500

Table des matières

Autres manuels Huawei Changer

Huawei

Huawei S1700 Series Manuel utilisateur

Huawei

Huawei CR-SRUB Manuel utilisateur

Huawei

Huawei B882 Manuel utilisateur

Huawei

Huawei S1720 Manuel d'utilisation

Huawei

Huawei S600-E Series Manuel utilisateur

Huawei

Huawei Quidway S9300 Manuel utilisateur

Huawei

Huawei Enterprise S2700 Series Manuel d'utilisation

Huawei

Huawei Quidway S3000-EI Series Manuel utilisateur

Huawei

Huawei MSOFTX3000 Mode d’emploi

Huawei

Huawei Enterprise S2700 Series Manuel utilisateur

Huawei

Huawei Quidway S9300 Manuel utilisateur

Huawei

Huawei ACBox2000-21-D-A Manuel utilisateur

Huawei

Huawei Quidway S3100 Series Manuel utilisateur

Huawei

Huawei B890 Manuel utilisateur

Huawei

Huawei Quidway S1700-8-AC Manuel d'utilisation et d'entretien

Huawei

Huawei Quidway S3900 Series Manuel utilisateur

Huawei

Huawei NE05E Manuel utilisateur

Huawei

Huawei Quidway S9300 Mode d’emploi

Huawei

Huawei Enterprise S2700 Series Manuel utilisateur

Huawei

Huawei S3700HI Manuel utilisateur

Huawei

Huawei B882 Manuel utilisateur

Huawei

Huawei S1700 Series Manuel utilisateur

Huawei

Huawei 7810 Manuel utilisateur

Huawei

Huawei Quidway S3000-EI Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur