HPRT TP80 Series Manuel d'instructions
Ethernet Connection Manual
TP80 SERIES
Rev.1.0
CONTENT
Introduction ............................................................................................................1
1. Connected directly by Ethernet cable..............................................................2
2. Connected by Router .......................................................................................8
3. Connected by Driver ......................................................................................21
4. Connected by Website ...................................................................................31
1
Introduction
This manual content may be changed without permission and our company reserve
the rights to make changes in technology, spare parts, hardware and software of the
products. Please contract our company, if the user needs further information about
the products. Without any written permission from our company, any section of this
manual is prohibited to be copied or transferred in any form.
The following are four types of Ethernet connections between printers and
computers:
●Connected directly by ethernet cable
●Connected by router
●Connected by driving software
●Connected by website
2
1. Connected directly by Ethernet cable
Connect the printer at one end of the network cable and the other end to the
computer in the following ways:
▉Modify the computer IP address
1）Open the printer tool software and select the current printer model. (Take TP80BE
as an example)
Note: The current computer is disconnected from the Internet
3
Click "Printer Test", select "Self Test", you can view the printer IP address from the
Self-test page.
For example, from the following Self-Test page information can know that the printer
IP address is: 10.0.16.40.
SELF-TEST
Brand:
HPRT
MODEL:
TP80BE
FW Version:
SV1 .00. 05
CG Version:
SV1 .00. 11
Serial Num
XXXXX
Interface: USB & Serial & Ethernet
Serial 9600, None,8,1,DTR/DSR
IP Adress:
10.0.16.40
SubnetMask
255.255.255.0
Gateway:
10.0.16.1
MAC Address
80：1F：12:99：B0:03
DHC
Disable
2）Modify the computer IP address in the following steps.
Click "Start"-"Control Panel" to find "Network and Internet". Click "Change Adapter
Settings".
4
￭Right-click the network and select “Properties”.
￭Double-click "TCP/IPv4" to enter the computer IP address modification page.
5
6
￭Change the COMPUTER address (for example, 10.0.16.33) so that the
COMPUTER IP address is in the same network segment as the printer IP address,
and in the figure, click OK.
4) After the COMPUTER re-recognizes the IP address, return to the main menu page
of the tool and click "Modify Printer".
7
5) Modify the “portInfo” to TCP/IP, and modify the IP address to the printer current
IP address, and click OK.
6) Return to the main page of tool menu and click "Connection Test". When pop up
the following "connection succeeded" means that the printer is connected to
the computer.
8
2.Connected by Router
When the printer and the computer are connected to the same router, the operation
is as follows:
▉One: Modify the printer IP address
1）View the computer IP address in the following ways:
￭Click "Start" and select "Run".
￭Input “cmd” and enter/ click “OK”.
Autres manuels pour TP80 Series
1
Table des matières
Autres manuels HPRT Imprimante
HPRT
HPRT TP801 Manuel utilisateur
HPRT
HPRT HD2000 Manuel utilisateur
HPRT
HPRT MT53 Manuel utilisateur
HPRT
HPRT MPT-II Manuel utilisateur
HPRT
HPRT SL42 Manuel utilisateur
HPRT
HPRT HM-E200 Manuel du propriétaire
HPRT
HPRT TP80BE Manuel utilisateur
HPRT
HPRT TP806L Manuel utilisateur
HPRT
HPRT MT800 Manuel utilisateur
HPRT
HPRT TP80K Manuel utilisateur
HPRT
HPRT HM-T300 Manuel utilisateur
HPRT
HPRT TP80K Manuel du propriétaire
HPRT
HPRT TP809 Manuel utilisateur
HPRT
HPRT GT1 Manuel utilisateur
HPRT
HPRT HM-A300 Manuel utilisateur
HPRT
HPRT HT130 Manuel utilisateur
HPRT
HPRT TP80 Series Manuel utilisateur
HPRT
HPRT FC53-Li Manuel utilisateur
HPRT
HPRT KP806 Manuel utilisateur
HPRT
HPRT HLP106D Manuel utilisateur
