HP 527 Manuel utilisateur
The HP 527 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED
802.11a/b/g/n/ac product. The Wi-Fi CERTIFIED Logo is a certification
mark of the Wi-Fi Alliance.
HP 527 Dual Radio 802.11ac Unified Wired-WLAN
Walljack quick start guide
This quick start guide shows you how to install and get started using the HP 527 Dual
Radio 802.11ac Unified Wired-WLAN Walljack (RMN BJNGA-FB0005) JH048A
(AM), JH049A (WW), JH050A (JP), JH051A(IL), JH052A (20 pack AM), JH053A (20
pack WW), hereafter referred to as the HP 527.
Hardware overview
Back view
1: Pass Through port
2: Uplink port
Front view
Bottom views
3: GigabitEthernet LAN ports 1 and 2
4: PoE Out GigabitEthernet LAN port 3
5: Pass Through port
1 2
345
1
2
1
Package contents
The HP 527, mounting bracket, screws, MAC address label, and documentation.
Ports
x
x
Three Gigabit Ethernet ports: Auto-sensing 1000Base-T Ethernet ports with RJ-45
connectors.
x
One Gigabit Ethernet uplink port: Auto-sensing 1000Base-T Ethernet port with RJ-
45 connector.
x
One pair of pass-through ports: Work with Cat5 cabling as well as an analog
telephone cable.
Radio and antennas
The HP 527 supports IEEE 802.11a/b/g/n/ac. It has two internal antennas
supporting 2x2 MIMO with two spatial streams at a rate of up to 850 Mbps.
Reset button
The reset button is accessible through a hole on the side panel of the HP 527. To reset
the HP 527, insert a paper clip into the reset button hole, and press and quickly
release the button. To reset the HP 527 to factory defaults, press and hold the button
more than 5 seconds until the status LEDs (Power, Radio, and Uplink) flash, then
release.
Status LEDs
Status LEDs power
PoE Out
Uplink
LAN ports 1, 2, and 3
Radio
2
Power Uplink Radio LAN (1 to 3) PoE Description
Off Off Off Off Off The AP has no power.
Steady orange Off Off Off Off
Power applied. If the
power LED remains orange
after several minutes, the
AP failed to load the
software.
Green, flashing
every 2 seconds
(0.5Hz)
Off Off Off Off The AP is starting up.
Green, flashing
every 2 seconds
(1Hz)
Off Off Off Off
The AP is looking for an IP
address or building the list
of VLANS on which to
perform discovery.
The power, uplink, and radio LEDs are
flashing green in sequence. Off Off
The AP has obtained an IP
address and is attempting
to discover a controller.
Steady green
The uplink and radio
LEDs are flashing
g
reen alternately.
Off Off
The AP has found a
controller and is attempting
to establish a tunnel with it.
The power and uplink LEDs
are alternately flashing green
(slowly).
Off Off Off
The AP is performing
Ethernet negotiation, and
is waiting for the Ethernet
link to come up.
Steady green Off Any Any Any
The uplink interface is not
connected or there is no
network activity.
Steady green Flashing
green Any Any Any
The uplink interface is
active on a valid
1000Mbps link.
Steady green Flashing
orange Any Any Any
The uplink interface is
active on a valid 100Mbps
link.
Steady green Any Off Any Any
The radio interfaces are
disabled or there is no
network activity.
Steady green Any Flashing
green Any Any
Only the 2.4GHz radio
interface is transmitting or
receivin
g
data.
Steady green Any Flashing
orange Any Any
Only the 5GHz radio
interface is transmitting or
receivin
g
data.
3
Power Uplink Radio LAN (1 to 3) PoE Description
Steady green Any
Flashing
green
and
orange
alternatel
y
Any Any
Both 2.4GHz and 5GHz
radio interfaces are
transmitting or receiving
data.
Steady green Any Any Off Any
The uplink interface is
disabled or there is no
network activity.
Steady green Any Any Flashing green Any
The LAN interfaces are
active on a valid
1000Mbps link.
Steady green Any Any Flashing
orange Any
The LAN interfaces
are active on a valid
100Mbps link.
Steady green Any Any Any Off
No PoE device is
connected.
Steady
g
reen Any Any Any On A PoE device is connected.
Powering the HP 527
The HP 527 can be powered by using a local power source, an uninterruptible power
supply (UPS), a user-supplied power generator, or a PoE-enabled switch that provides
10/10 0 Mb p s or 10 / 100/ 10 0 0 Mbps Eth e rn e t ports.
Before you connect power to the AP, verify that the power supply is steady.
The HP 527 supports an 802.3af PoE PSE connection to one device on LAN port 3.
This feature is dependent on the power source of the HP 527, as follows:
x
x
Supports 802.3af class 1/2/3 PoE Out when the 803.3at (PoE+) power supply
mode is used.
x
Do not support PoE Out when the standard 803.3af power supply mode is used.
Important information to read before installing
Professional installation is required. For indoor installation only. Before installing or
using the AP, consult with a professional installer trained in RF installation and
knowledgeable in local regulations including building and wiring codes, safety,
channel, power, and license requirements for the intended country. The end user is
responsible for ensuring that installation and use comply with local safety and radio
regulations.
4
To avoid possible bodily injury or equipment damage, read the following safety
recommendations before you install an HP 527. The recommendations do not cover
every possible hazardous condition.
x
x
Install with six inches or more of clearance around the walljack.
x
Keep the chassis clean and dust-free.
x
Make sure the ground is dry and flat and anti-slip measures are in place.
x
Do not place the AP in a moist area and avoid liquid surrounding the AP.
x
Keep the chassis and installation tools away from walkways.
Installation
1. Place the mounting bracket, with the UP arrow pointing up, on the electrical
outlet box, and then use two of the supplied mounting screws to secure the
bracket to the box.
The two long mounting screws are for a US electrical box. The two short
mounting screws are for an EU electrical outlet box.
Long mounting screw Short mounting screw
5
Figure 1 Securing the mounting bracket to an electrical outlet box (EU)
Figure 2 Securing the mounting bracket to an electrical outlet box (US)
M3.5 × 25
M3.5 × 25
6
2. Connect the network cable from the box to the RJ-45 Uplink port on the back of
the HP 527. If required, also connect the cable providing support for pass-
through devices to the Pass Through port on the back of the HP 527.
Figure 3 Connecting the network cable
7
3. Align the installation hole in the rear of the AP with the standout on the mounting
bracket.
Figure 4 Aligning the installation hole
8
4. Push the HP 527 onto the mounting bracket, and then slide it down until it is fully
engaged. Then secure the AP to the bracket by using the Phillips-head screw or
the security-head security Torx-10 screw.
Do not let go of the HP 527 until you confirm that it is securely in place.
Figure 5 Securing the AP
1
2
9
Provided access services
After the installation is complete, connect equipment to the HP 527 as follows:
Technical support
For worldwide technical support information, see the HP support website at
www.hp.com/networking/support.
Other regulatory information
For important safety, environmental, and regulatory information, see Safety and
Compliance Information for Server, Storage, Power, Networking, and Rack Products,
available at www.hp.com/support/Safety-Compliance-EnterpriseProducts.
FCC Notice
This device must not be co-located with any other transmitters except in accordance
with FCC multi-transmitter product procedures.
Printer Laptop
Phone
IP Phone
PoE Switch
IP TV
PC
Pass Through
10
Autres manuels pour 527
1
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels HP Point d'accès sans fil
HP
HP 600R Series Manuel utilisateur
HP
HP AP-503H Instructions de montage
HP
HP MSM310-R Manuel utilisateur
HP
HP 425 - Notebook PC Manuel utilisateur
HP
HP WL520 Manuel utilisateur
HP
HP MSM410 Manuel utilisateur
HP
HP ProCurve 420 Manuel utilisateur
HP
HP MSM3xx Manuel utilisateur
HP
HP MSM410 Manuel utilisateur
HP
HP ProCurve 420 Manuel utilisateur
HP
HP 425 - Notebook PC Manuel utilisateur
HP
HP MSM310 Manuel utilisateur
HP
HP Aruba AP-577 Instructions de montage
HP
HP Compaq Presario,Presario 650 Manuel utilisateur
HP
HP MSM-802.11n Instructions d'utilisation
HP
HP 530 - Notebook PC Manuel de programmation
HP
HP MSM3xx Manuel utilisateur
HP
HP MSM-802.11 series Manuel utilisateur
HP
HP J9374A Guide d'installation
HP
HP MSM310 Comment utiliser
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
