HP 527 Manuel utilisateur

The HP 527 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11a/b/g/n/ac

product. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi

Alliance.

Unified Wired-WLAN Walljack (HP 527 Dual Radio

802.11ac) quick start guide

This quick start guide shows you how to install and get started using the HP 527

Dual Radio 802.11ac Unified Wired-WLAN Walljack (RMN BJNGA-FB0005) JH048A

(AM), JH049A (WW), JH050A (JP), JH051A(IL), JH052A (20 pack AM), JH053A (20

pack WW), hereafter referred to as the HP 527.

Hardware overview

Back view

1: Pass Through port

2: Uplink port

Front view

Bottom views

3: GigabitEthernet LAN ports 1 and 2

4: PoE Out GigabitEthernet LAN port 3

5: Pass Through port

1 2

345

Package contents

The HP 527, mounting bracket, screws, MAC address label, and documentation.

Ports

Three Gigabit Ethernet ports: Auto-sensing 1000Base-T Ethernet ports with

RJ-45 connectors.

One Gigabit Ethernet uplink port: Auto-sensing 1000Base-T Ethernet port with

RJ-45 connector.

One pair of pass-through ports: Work with Cat5 cabling as well as an analog

telephone cable.

Radio and antennas

The HP 527 supports IEEE 802.11a/b/g/n/ac. It has two internal antennas supporting

2x2 MIMO with two spatial streams at a rate of up to 850 Mbps.

Reset button

The reset button is accessible through a hole on the side panel of the HP 527. To

reset the HP 527, insert a paper clip into the reset button hole, and press and

quickly release the button. To reset the HP 527 to factory defaults, press and hold

the button more than 5 seconds until the status LEDs (Power, Radio, and Uplink)

flash, then release.

Status LEDs

Status LEDs power

PoE O ut

Uplink

LAN ports 1, 2, and 3

Radio

Power

Uplink

Radio

LAN (1 to 3)

PoE

Description

Off

The AP has no power.

Steady orange

Off

Power applied. If the

power LED remains

orange after several

minutes, the AP failed to

load the software.

Green, flashing

every 2 seconds

(0.5Hz)

Off

The AP is starting up.

Green, flashing

every 2 seconds

(1Hz)

Off

The AP is looking for an IP

address or building the list

of VLANS on which to

perform discovery.

The power, uplink, and radio LEDs are

flashing green in sequence.

Off

The AP has obtained an IP

address and is attempting

to discover a controller.

Steady green

The uplink and radio

LEDs are flashing

green alternately.

Off

The AP has found a

controller and is

attempting to establish a

tunnel with it.

The power and uplink LEDs

are alternately flashing green

(slowly).

Off

The AP is performing

Ethernet negotiation, and

is waiting for the Ethernet

link to come up.

Steady green

Off

Any

The uplink interface is not

connected or there is no

network activity.

Steady green

Flashing

green

Any

The uplink interface is

active on a valid

1000Mbps link.

Steady green

Flashing

orange

Any

The uplink interface is

active on a valid 100Mbps

link.

Steady green

Any

Off

Any

The radio interfaces are

disabled or there is no

network activity.

Steady green

Any

Flashing

green

Any

Only the 2.4GHz radio

interface is transmitting or

receiving data.

Steady green

Any

Flashing

orange

Any

Only the 5GHz radio

interface is transmitting or

receiving data.

Power

Uplink

Radio

LAN (1 to 3)

PoE

Description

Steady green

Any

Flashing

green

and

orange

alternate

Any

Both 2.4GHz and 5GHz

radio interfaces are

transmitting or receiving

data.

Steady green

Any

Off

Any

The uplink interface is

disabled or there is no

network activity.

Steady green

Any

Flashing green

Any

The LAN interfaces are

active on a valid

1000Mbps link.

Steady green

Any

Flashing

orange

Any

The LAN interfaces

are active on a valid

100Mbps link.

Steady green

Any

Off

No PoE device is

connected.

Steady green

Any

A PoE device is connected.

Powering the HP 527

The HP 527 can be powered by using a local power source, an uninterruptible power

supply (UPS), a user-supplied power generator, or a PoE-enabled switch that

provides 10/100 Mbps or 10/100/1000 Mbps Ethernet ports.

Before you connect power to the AP, verify that the power supply is steady.

The HP 527 supports an 802.3af PoE PSE connection to one device on LAN port 3.

This feature is dependent on the power source of the HP 527, as follows:

Supports 802.3af class 1/2/3 PoE Out when the 803.3at (PoE+) power supply

mode is used.

Do not support PoE Out when the standard 803.3af power supply mode is used.

Important information to read before installing

Professional installation is required. For indoor installation only. Before installing or

using the AP, consult with a professional installer trained in RF installation and

knowledgeable in local regulations including building and wiring codes, safety,

channel, power, and license requirements for the intended country. The end user is

responsible for ensuring that installation and use comply with local safety and radio

regulations.

To avoid possible bodily injury or equipment damage, read the following safety

recommendations before you install an HP 527. The recommendations do not cover

every possible hazardous condition.

Install with six inches or more of clearance around the walljack.

Keep the chassis clean and dust-free.

Make sure the ground is dry and flat and anti-slip measures are in place.

Do not place the AP in a moist area and avoid liquid surrounding the AP.

Keep the chassis and installation tools away from walkways.

Installation

1. Place the mounting bracket, with the UP arrow pointing up, on the electrical

outlet box, and then use two of the supplied mounting screws to secure the

bracket to the box.

The two long mounting screws are for a US electrical box. The two short

mounting screws are for an EU electrical outlet box.

Long mounting screw Short mounting screw

Figure 1 Securing the mounting bracket to an electrical outlet box (EU)

Figure 2 Securing the mounting bracket to an electrical outlet box (US)

M3.5 × 25

2. Connect the network cable from the box to the RJ-45 Uplink port on the back of

the HP 527. If required, also connect the cable providing support for

pass-through devices to the Pass Through port on the back of the HP 527.

Figure 3 Connecting the network cable

3. Align the installation hole in the rear of the AP with the standout on the

mounting bracket.

Figure 4 Aligning the installation hole

4. Push the HP 527 onto the mounting bracket, and then slide it down until it is

fully engaged. Then secure the AP to the bracket by using the Phillips-head

screw or the security-head security Torx-10 screw.

Do not let go of the HP 527 until you confirm that it is securely in place.

Figure 5 Securing the AP

/ PC

Wireless AP

Provided access services

After the installation is complete, connect equipment to the HP 527 as follows:

Technical support

For worldwide technical support information, see the HP support website at

www.hp.com/networking/support.

Other regulatory information

For important safety, environmental, and regulatory information, see Safety and

Compliance Information for Server, Storage, Power, Networking, and Rack Products,

available at www.hp.com/support/Safety-Compliance-EnterpriseProducts.

Caution

This product can’t use channel 12/13 for 2.4GHz band and the country code is

locked that the users can’t modify it.

Printer Laptop

Phone

PoE Switch

IP TV

Pass Through

Autres manuels pour 527

Table des matières

Autres manuels HP Changer

HP ProCurve 8212zl Series Manuel utilisateur

HP HP ProCurve Series 6600 Manuel utilisateur

HP 5400R zl2 Series Manuel utilisateur

HP StorageWorks 2/8-EL - SAN Switch Mode d’emploi

HP 6125XLG Manuel utilisateur

HP 6125G Manuel d'installation

HP 5920 Manuel utilisateur

HP Aruba Instant On 1430 Instructions d'installation

HP FlexFabric 7900 Series Manuel utilisateur

HP 316095-B21 - StorageWorks Edge Switch 2/24 Mode d’emploi

HP StorageWorks 2/140 - Director Switch Manuel utilisateur

HP 6125XLG Manuel d'installation

HP 12500 Series Manuel utilisateur

HP 445946-001 Guide de l'utilisateur

HP ProCurve 2520-24-PoE Manuel

HP 372284-001 Manuel utilisateur

HP ProCurve J8766A Manuel utilisateur

HP E4510-48G Manuel d'utilisation

HP invent ProCurve J4908A Manuel utilisateur

HP Aruba Instant On 1830 Instructions d'installation

HP ProCurve Switch 2650 Manuel utilisateur

HP ProCurve Switch 2900yl-24G Manuel utilisateur

HP PROCURVE 6120 Manuel utilisateur

HP 1410 series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur