HP StorageWorks 600 - Modular Disk System Feuille d'instructions

Important

Rack Installation Guidelines

for the HP BladeSystem 70 Scalable Storage Array and

the HP StorageWorks 600 Modular Disk System

Overview

This document provides guidelines for installing an HP BladeSystem

70 Scalable Storage Array or HP StorageWorks 600 Modular Disk

System into a rack.

Rack installation guidelines

WARNING: When configuring a solution, make sure that

the floor loading specifications are followed. Failure to do

so can result in physical injury or damage to the

equipment and the facility.

WARNING: The storage array with no drives installed

weighs 72.58 kg (160.00 lb). With all drives and

components installed, the storage array can weigh up to

145.15 kg (320 lb). Before configuring your rack solution,

be sure to check the manufacturer weight limits and

specifications. Failure to do so can result in physical injury

or damage to the equipment and the facility.

Observe the following guidelines when installing the SSA70 or

MDS600 into a rack:

•Do not install the SSA70 or MDS600 in the bottom of a rack

other than an HP10000. To install the SSA70 or MDS600 in

the bottom of an HP10000 rack, you must first install a support

bracket and spacer. See "Installing a rack support bracket."

•To install the SSA70 or MDS600 into a third-party rack, or

above any component other than a c3000 enclosure, c7000

enclosure, or another SSA70 or MDS600, you must first install

a support tray. See "Installing a support tray."

•To install an SSA70 or MDS600 above a c3000 or c7000

enclosure, you must first attach a spacer to the top of the

enclosure. See "Attaching a spacer to an enclosure installed

below an SSA70 or MDS600."

•No spacer is required when installing one SSA70 or MDS600

above another SSA70 or MDS600.

Example rack configurations

Item Description

1 SSA70 or MDS600 installed above a support

bracket

2 SSA70 or MDS600

3 c7000 enclosure with a spacer installed

4 SSA70 or MDS600

Item Description

1 c7000 enclosure with a spacer installed

2 SSA70 or MDS600

3 SSA70 or MDS600

Item Description

1 Server

2 Support tray with a spacer installed

3 SSA70 or MDS600

4 SSA70 or MDS600

Item Description

1 c7000 enclosure

2 PDU

3 Support tray with a spacer installed

4 SSA70 or MDS600

5 SSA70 or MDS600

Installing a rack support bracket

1. Place the support bracket in the bottom of the rack and align

with the screw holes in front of the rear vertical rails.

The information contained herein is subject to change without notice. The

only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing

herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Part Number 498381-002

December 2008 (Second Edition)

Printed in the United States

498381- 002

2. Install three screws on each side of the bracket.

3. Attach a spacer to the front caster plate. Center the spacer

approximately 2.54 to 7.62 cm (1.00 to 3.00 in) behind the

front edge of the caster plate. Apply pressure to adhere the

spacer to the caster plate.

Installing a support bracket riser

To install the component:

1. Place the riser on top of the support bracket, aligning the

mounting holes.

2. Secure the riser to the support bracket with the provided self-

tapping screws.

The installation is complete.

Attaching a spacer to an

enclosure installed below an

SSA70 or MDS600

If the SSA70 or MDS600 is being installed in the rack directly above

a c3000 or c7000 enclosure, a spacer must be adhered to the top

of the c3000 or c7000 enclosure.

IMPORTANT: Do not attach the spacer to an SSA70 or

MDS600 unit.

1. Remove the protective backing from the spacer.

2. Center the spacer approximately 2.54 to 7.62 cm (1.00 to

3.00 in) behind the front edge of the enclosure. Apply pressure

to adhere the spacer to the enclosure.

IMPORTANT: Do not cover any labels on the enclosure

when attaching the spacer.

Installing a support tray

1. Install two clip nuts on each side of the front and rear of the

rack at the top and bottom of a 1U space.

2. Install each rear side bracket using two screws. Do not fully

tighten the screws. L (left) and R (right) markings indicate the

correct side for installation when viewed from the front of the

rack. The support pin should be facing inward.

3. Insert the support tray into the rack front.

4. Set the support tray on the support pins on the rear side

brackets.

5. Install four screws to secure the front of the support tray to the

rack, and then tighten all four front screws.

6. Install two screws through the rear of the support tray into the

threaded inserts on the rear side brackets, and then tighten all

screws.

7. Center the spacer approximately 2.54 to 7.62 cm (1.00 to

3.00 in) behind the front edge of the support tray. Apply

pressure to adhere the spacer to the support tray.

Autres manuels pour StorageWorks 600 - Modular Disk System

Autres manuels HP Stockage

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manuel utilisateur

HP 500 G2 Guide d'installation

HP 3PAR StoreServ 7200 2-node Manuel utilisateur

HP StorageWorks Disk System 2405 Manuel d'utilisation et d'entretien

HP Surestore Disk Array 12h - And FC60 Manuel utilisateur

HP 3PAR StoreServ 7200 2-node Manuel d'utilisation et d'entretien

HP StorageWorks DAT 72 Instructions d'utilisation

HP Surestore 64 - Director Switch Manuel utilisateur

HP X510 Instructions d'utilisation

HP StorageWorks 8B - FC Entry Switch Manuel utilisateur

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manuel utilisateur

HP HPE XP P9500 Manuel utilisateur

HP 4X Manuel utilisateur

HP 157770-001 - DAT Drive 20/40 Tape Manuel utilisateur

HP BAAD0010HBK-NHSN Manuel utilisateur

HP StorageWorks 12000 Mode d’emploi

HP D2D Manuel utilisateur

HP StorageWorks MSA500 G2 Manuel utilisateur

HP EVA P6000 Manuel utilisateur

HP STORAGEWORKS XP24000 Manuel utilisateur

HP D2D100 Manuel utilisateur

HP Pavilion p6000 - Desktop PC Mode d’emploi

HP StorageWorks 8000 - NAS Manuel utilisateur

HP SuperStore E SC10 Manuel

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur