Honeywell RP2B Manuel utilisateur

RP2B/RP2D/RP4B/RP4D*

Thermal Printers

Quick Start Guide

RP234-EN-QS Rev C

10/18

*For China, models RP2B-C, RP2D-C, RP4B, RP4D-C

*For Thailand models RP2B, RP2D-T, RP4B, RP4D-T

Get Started

1. Install the battery in the printer. Align the release tab with

the same side as the charge contacts and lock the battery

into position. The latch clicks into place when properly

seated.

2. Connect the power supply to printer’s power jack.

3. Connect the AC power cord to the power supply and plug

into an outlet.

Do not operate the printer while it is connected to the

AC power supply.

Load Labels or Paper

Load labels or paper into the printer as follows:

1. Press down on the latch lock and lift up the printer’s cover.

2. Slide and hold open the supply hubs.

3. Orient the paper as shown and insert into the printer.

4. Allow the supply hubs to retract onto the paper roll, then

press the cover down until it latches.

5. Press the media button 2 or 3 times to normalize

tracking. Each button press advances the paper to the start

of the next label.

Download Required Software

1. Create a new folder on your local computer named Drivers.

2. Go to the Technical Support Downloads Portal at https://

hsmftp.honeywell.com.

3. Go to:

Software

- Printers

- Mobile - Portable

- RP2 RP3 RP4

- Utility 

to download the NETira® CT Printer Configuration Utility.

4. When prompted, click on Open Honeywell Software

Downloader.

5. Once the file has been downloaded, extract it to your

Drivers folder.

6. Go to:

Software

- Printers

- Mobile - Portable

- RP2 RP3 RP4

- Drivers

- Printer 

to download the Windows Printer Drivers (for DPL Input

Mode).

7. When prompted, click on Open Honeywell Software

Downloader.

8. Once the file has been downloaded, extract it to your

Drivers folder.

9. Open the Drivers folder and double-click each of the

setup.exe files. Follow the prompts to install each piece of

software.

Add the Printer to Your Host System

The default USB class is CDC Composite. On some systems (e.g.,

handheld devices), you will have to change this USB class in

order to connect. See your User Guide for further information.

1. Connect the USB cable to the printer and to the USB port on

the host system.

2. Power up your printer.

3. Your host computer should recognize the printer and begin

adding the device driver. If the setup operation does not

start, locate the Devices and Printers section in the Control

Panel and select Add a Printer.

4. Select the appropriate RP printer model and follow the

prompts to finish installation.

Configure the Printer

1. Turn the printer on and connect it to the computer using the

USB cable.

2. Open the NETira™CT Printer Configuration Utility Tool.

3. Query the printer by clicking Tools - Update Available

Connections For Printer. This will look for the USB Virtual

COM Port.

4. Once this is completed, reopen the dropdown menu and

select the USB Virtual COM port.

Note: Make sure this port is not in use by the printer driver when

you add it to the host system.

5. Press CTRL-q to display the printer’s configuration.

See your User Guide for detailed information about changing

the printer’s settings.

Front Panel

On/Off Button

Button Press Result

Any length press when printer is off Turn printer on

Short press (less than 5 seconds) Enter or exit sleep mode

Medium press (5 - 10 seconds) Print configuration label

Long press (more than 10 seconds) Turn printer off

On/Off

Button

Media

Button

Battery

Charge

Level Bluetooth

Indicator

WiFi

Signal

LED Display

Media Button

The media button advances the paper through the printer. When

there is no paper in the printer, the button blinks red.

Icon Indication

Battery

charge

level

When not charging:

Off = Battery is midway to fully charged

Solid orange = Battery charge is 10-30%

Blinking red = Battery charge is 10% or less

When charging:

Solid green = Battery charge is 90% or more

Solid red = Battery charge is less than 90%

Bluetooth

indicator

Off = Bluetooth radio is off, disabled, not associated

with a mobile device, or printer is off

Blinking = Data transmission

Solid blue = Bluetooth is enabled and connected

WiFi

signal

Off = WiFi radio is off, disabled, not associated with a

mobile device or network, or printer is off

White = WiFi is enabled and connected

Button Press Result

Short press Feeds label or paper length

Press and hold (when configured for

continuous form receipt paper)

Media feeds continuously to

the maximum label length

Autres manuels pour RP2B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Imprimante

Honeywell

Honeywell PB22 Manuel utilisateur

Honeywell

Honeywell MP Compact4 Manuel utilisateur

Honeywell

Honeywell MP Compact Mark III Manuel utilisateur

Honeywell

Honeywell PD45 Manuel utilisateur

Honeywell

Honeywell datamax-o'neil M-Class Mark II Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell RFID Kit Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell Intermec PD43 Manuel utilisateur

Honeywell

Honeywell RP2 Manuel utilisateur

Honeywell

Honeywell IMPACT IHR810 Manuel utilisateur

Honeywell

Honeywell PC300T Manuel utilisateur

Honeywell

Honeywell PM43 Manuel utilisateur

Honeywell

Honeywell PC42E-T Manuel utilisateur

Honeywell

Honeywell CN51 PrintPAD Manuel utilisateur

Honeywell

Honeywell PX940 Manuel utilisateur

Honeywell

Honeywell CN51 PrintPAD Manuel utilisateur

Honeywell

Honeywell PX4ie Manuel utilisateur

Honeywell

Honeywell PX4i Manuel utilisateur

Honeywell

Honeywell PRU0901 Manuel utilisateur

Honeywell

Honeywell PC43K Manuel utilisateur

Honeywell

Honeywell PC45 Series Manuel utilisateur

Honeywell

Honeywell PC42d Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur