Honeywell Datamax-o'neil M-Class Mark II Manuel utilisateur

RFID Ready Option

92-2499-01 Rev.C

Overview

This document describes the contents and installation of the M-Class Mark II RFID options.

Only qualified service personnel should perform this installation. After verifying the kit

contents and the tools needed, follow the steps below to install the option.

• This RFID device complies with FCC Radio Frequency exposure limits for an

uncontrolled environment. This equipment should be installed and operated

with a minimum distance of 20cm between the radiator and your body. If

20cm distance cannot be maintained, end users are to be 20cm from

printer extremity.

• Any changes or modifications to this RFID module not expressly approved

by Datamax-O’Neil Corporation will void the user’s authority to operate the

equipment.

• RFID operation is subject to the following two conditions: (A) this device

may not cause interference, and (B) this device must accept any

interference, including interference that may cause undesired operation of

this device.

• For your safety and to avoid equipment damage, always turn OFF power

and unplug the printer’s power cord before beginning this installation and

when performing service.

CAUTION

• To avoid equipment damage, never apply power to the printer with the

Antenna Cable disconnected.



Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their own expense.

Contents

The contents of the kit differ according to the type of RFID option:

HF Option*:

1Antenna

2Regulator CCA

3Mounting Plate

4Power Cable

5Comm Cable

6Screw (3), M4 HD 8

7Double-Sided Tape

8Screw, M4 HD 25

9Short Spacer (2), .34 X .31

10 Long Spacer, .25 X .62

11 Washer

12 RF Shield

13 FCC Label

14 HF Module

UHF Option*:

1Antenna

2Regulator CCA

3Mounting Plate

4Power Cable

5Communications Cable

6Screw (3), M4 x 8

7Double-Sided Tape

8Screw (4), M3 x 6

9I/O Cable

10 UHF Module

11 Standoff (4) M3x13

678

*Also included, but not shown, is the RFID Quick Start Guide (P/N 92-2450-01).

Tools Required

A Phillips screwdriver is needed, and a PC with an Internet connection may also be required.

Step 1: Checking Firmware

A) Verify the firmware version in the printer:

Press the TEST Button on the Control Panel.

Using the DOWN Button, scroll to PRINT

CONFIGURATION and press TEST.

PAUSE FEED CANCEL

WED 09:32A 23APR2008

READY

TEST

READY STOP ERROR Control Panel

B) Examine the Application Version printed on

the Configuration Label and proceed

accordingly:

• If 14.09 (or greater), go to Step 2; or,

• If 14.08 (or less), go to ftp.datamax-

oneil.com and download a new version.

Follow the “Updating Firmware”

instructions in the Operator’s Manual and

install the update.

FORMAT ATTRIBUTES:l

XOR

LABEL ROTATION:

DISABLED

IMAGING MODE:

MULTIPLE LABEL

PAUSE MODE:

DISABLED

PEEL MODE:

DISABLED

SECURITY:

DISABLED

UNITS OF MEASURE:

IMPERIAL

INPUT MODE:

DPL

CONFIGURATION

THU 09:09 AM 24APR2008

PRINTER KEY:

4210-MG10-071010-027

APPLICATION VERSION:

83-2625-10H 10.07 07/24/2007

BOOT LOADER:

83-2627-10G 10.05 06/15/2007

UNLOCKED:

CG TIMES

FPGA:

MA05

iPH:

32-56777

Application Version

Configuration Label

Step 2: Preparing the Printer

CAUTION

Always wear a wrist strap and follow ESD prevention measures when

handling circuit card assemblies.

A) Turn OFF the Power Switch and unplug the

power cord from the AC Receptacle.

Power Switch

AC Receptacle

B) Remove the Cover Screws on the

outside of the printer.

Cover Screws

C) Raise the Cover. Loosen the

Cover Screws on the

Centerplate then remove the

Cover.

Cover Screws

Cover

Centerplate

D) Remove the Fascia,

Thumbscrew and

Tearbar (or other

output attachment).

Press the Printhead

Latch, and then raise

the Printhead

Assembly. Remove

media from the printer.

Printhead Assembly

Thumbscrew

Tearbar

Fascia

Printhead Latch

Step 3: Installing the Option

A) Peel the backing from the

Double-Sided Tape (Item 7).

Affix the Double-Sided Tape

to the recessed area of the

Antenna Mount.

If installing the HF Option,

proceed to B; otherwise, go to

Antenna Mount

Double-Sided Tape

B) HF Option, only –

Peel the backing from the RF Shield (Item 12).

Affix the RF Shield to the Antenna (Item 1) in

the area as shown, right.

RF Sheild

(HF Option, only)

Antenna

C) According to the option type,

cut the tape over the HF

Opening or UHF Opening in

the Antenna Mount. Route

the Antenna Cable through

the opening. If installing the

HF Option, orient the RF

Shield over the UHF

Opening.Affix the Antenna

(Item 1) in the Antenna

Mount.

Antenna Mount

Antenna Cable

Antenna

HF Opening

UHF Opening

D) Route the Antenna Cable

through the Cableway in the

Centerplate.

Centerplate

Cableway

Antenna Cable

E) Loosen the Guide Screw

and the Heat Sink Screw

then slide the Notched

Tabs of the Mounting

Plate (Item 3)

underneath. Secure the

Mounting Plate to the

Centerplate using the

Screw (Item 6) and then

tighten the Guide Screw

and the Heat Sink Screw.

Screw

Mounting

Plate

Centerplate

Notched

Tab

Notched

Tab

Heat Sink

Screw

Guide Screw

F) Secure the Regulator CCA

(Item 2) to the Mounting

Plate using the Screws

(Item 6) then proceed

according to the option

type:

Mounting

Plate

Regulator

CCA

Screws

HF Option:

G) Place the Washer (Item

11) and then the Long

Spacer (Item 10) onto the

Screw (Item 8). Place a

Short Spacer (Item 9)

over the Long Spacer and

Screw. Insert the Long

Spacer and Screw

through the HF Module

(Item 14). Place a Short

Spacer (Item 9) over the

Long Spacer and Screw

then secure the assembled

parts to the Mounting

Plate, as shown.

Short

Spacer

Mounting

Plate

Screw

Short

Spacer

Long

Spacer

Module

Washer

H) Affix the FCC Label (Item

13) to the Mounting

Plate. Route the Antenna

Cable behind the

Mounting Plate and then

connect the cables

according to the table

below:

Regulator

CCA

Mounting

Plate

Power

Supply CCA

Main Logic

CCA

Antenna

Port

J2 J3

I/O

J12

Antenna

Cable

Module

FCC Label

Cable From To

Antenna Cable Antenna Antenna Port – HF Module

Power Cable (Item 4) J7 – Power Supply CCA J1 - Regulator CCA

Comm Cable (Item 5) J12 –Main Logic CCA J2 – Regulator CCA

I/O HF Module J3 – Regulator CCA

UHF Option:

G) Secure the UHF Module (Item 10) to the Mounting Plate using the four Standoffs

(Item 11) and four Screws (Item 8).

Standoffs

Screws

UHF

Module

Mounting

Plate

H) Route the Antenna

Cable behind the

Mounting Plate and

then connect the cables

according to the table

below:

Mounting

Plate

Regulator

CCA

Power

Supply CCA

J12

Main Logic

CCA

Antenna

Port

Antenna

Cable

UHF

Module

J1 J2

Cable From To

Antenna Cable Antenna Antenna Port J1 – UHF

Module

Power Cable (Item 4) J7 – Power Supply CCA

J1 - Regulator CCA

Comm Cable (Item 5) J12 –Main Logic CCA J2 – Regulator CCA

I/O Cable (Item 9) J2 – UHF Module J3 – Regulator CCA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Imprimante

Honeywell

Honeywell E-Class Series Manuel utilisateur

Honeywell

Honeywell PC43K Manuel utilisateur

Honeywell

Honeywell E-Class MK IIIA Manuel utilisateur

Honeywell

Honeywell PM43 Manuel utilisateur

Honeywell

Honeywell MP Compact4 Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell PC42d Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell PX4ie Manuel utilisateur

Honeywell

Honeywell IMPACT IHR810 Manuel utilisateur

Honeywell

Honeywell PC45 Series Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell RFID Kit Manuel utilisateur

Honeywell

Honeywell Intermec PD43 Manuel utilisateur

Honeywell

Honeywell PC42T Manuel utilisateur

Honeywell

Honeywell RP2 Manuel utilisateur

Honeywell

Honeywell PRU7070 Manuel utilisateur

Honeywell

Honeywell PX940 Manuel utilisateur

Honeywell

Honeywell 6824 Manuel utilisateur

Honeywell

Honeywell PC42E-T Manuel utilisateur

Honeywell

Honeywell PC300T Manuel utilisateur

Honeywell

Honeywell CN51 PrintPAD Manuel utilisateur

Honeywell

Honeywell PD45 Manuel utilisateur

Honeywell

Honeywell PM42 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

Honeywell datamax-o'neil M-Class Mark II Manuel utilisateur

Manuels Imprimante populaires d'autres marques