Honeywell CIU 888 Manuel utilisateur
$*6
Sealing Guide
Release R160
Preface
Part No.: 4417595_Rev10 Sealing Guide
CIU 888 i
$*6
PREFACE
General
A sealing facility of systems that is needed to ensure the accuracy of
settings used for calculating volume/mass must not be allowed to be
changed undetected. After verification by a legal metrology authority
(e.g. NMi), the system settings of the CIU 888 can be locked and the
system can be sealed by the authorized representative. By sealing the
CIU 888, the W&M authority states that the settings are conform the
national/local certifications, and that the system is allowed to be used to
support W&M certified applications for custody transfer, accounting and
duties.
Purpose of this manual
The purpose of this manual is to provide information about sealing the
CIU 888.
Target audience of this manual
This manual is primarily intended for:
Representatives of the W&M authorities who are responsible for
sealing the CIU 888
W&M accredited users who are responsible for sealing the CIU 888
Service technicians who are responsible for commissioning and
configuring the CIU 888, and who may need to break the seal of the
CIU 888 in order to change the configuration settings
Other users who may need to break the seal of the CIU 888 in order
to change the configuration settings
Preface
Sealing Guide Part No.: 4417595_Rev10
ii CIU 888
$*6
This page is intentionally left blank
Table of Contents
Part No.: 4417595_Rev10 Sealing Guide
CIU 888 iii
$*6
TABLE OF CONTENTS
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Purpose of this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Target audience of this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
CHAPTER 1 Sealing the CIU 888 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1 Unlocking the configuration settings of the CIU 888 . . . . . . . . . . . . . . . . . . . 1-1
1.2 Verifying the W&M relevant configurations settings of the CIU 888 . . . . . . . 1-2
1.3 Sealing the Entis Pro system connected to the CIU 888. . . . . . . . . . . . . . . . 1-5
1.4 Calibrating the entities of the tanks associated with the CIU 888 . . . . . . . . . 1-5
1.4.1 Ambient temperature calibration through CIU 888 web interface . . . . . . . . . 1-6
1.5 Locking the W&M relevant configuration settings of the CIU 888 . . . . . . . . . 1-7
1.6 Sealing the CIU 888 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
APPENDIX A List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Table of Contents
Sealing Guide Part No.: 4417595_Rev10
iv CIU 888
$*6
This page is intentionally left blank
Table of Contents
Part No.: 4417595_Rev10 Sealing Guide
CIU 888 1
$*6
CHAPTER 1 SEALING THE CIU 888
The procedure for sealing the CIU 888 consists of the following steps:
1. Unlocking the configuration settings of the CIU 888, see section 1.1
2. Verifying the W&M relevant configurations settings of the CIU 888,
see section 1.2
3. Sealing the Entis Pro system connected to the CIU 888, see
section 1.3
4. Calibrating the entities of the tanks associated with the CIU 888, see
section 1.4
5. Locking the W&M relevant configuration settings of the CIU 888, see
section 1.5
6. Sealing the CIU 888, see section 1.6
1.1 Unlocking the configuration settings of the CIU 888
The first step in the procedure for sealing the CIU 888, is unlocking both
the W&M relevant and the non-W&M relevant configuration settings of
the CIU 888. The configuration settings of the CIU 888 can be unlocked
using the W&M lock key switch and the Configuration lock key switch
located at the front of the CIU 888 (see FIGURE 1-1).
FIGURE 1-1 CIU 888: W&M lock key switch (left) and Configuration lock key switch (right)
To unlock the configuration settings, insert the key in the key switch and
turn it clockwise. The status of the W&M lock key switch and the
Table of Contents
Sealing Guide Part No.: 4417595_Rev10
2 CIU 888
$*6
Configuration lock key switch is displayed on the CIU 888 display (see
FIGURE 1-2).
FIGURE 1-2 CIU 888 display: Configuration settings are unlocked
1.2 Verifying the W&M relevant configurations settings of the CIU 888
It is recommended to verify the W&M relevant configuration settings of
the CIU 888. The purpose of verification is to establish that all W&M
relevant configuration settings stated in the certificate issued by the
legal metrology authority (e.g. NMi) have been configured correctly. The
W&M configuration settings can be verified using the CIU 888 Web
interface.
Perform the following steps to verify the W&M relevant configuration
settings:
1. Connect a PC/laptop with a standard web browser, i.e. Internet
Explorer 9 or 10, to the Service port of the CIU 888 using a Cat. 5
Ethernet cable (patch or crossover). The Service port is located at
the front of the CIU 888 (see FIGURE 1-3).
FIGURE 1-3 CIU 888: Service port
Table of Contents
Part No.: 4417595_Rev10 Sealing Guide
CIU 888 3
$*6
2. Launch the web browser.
3. Enter the IP address of the CIU 888 in the address bar of the web
browser. The IP address is 192.1681.1. Next, press the Enter key.
The CIU 888 Login window is displayed (see FIGURE 1-4).
FIGURE 1-4 CIU 888 Login window
4. Enter the username and password to log in to the CIU 888. The
username is ciuadmin. Next, click LOG IN.
After entering a valid username and password, the CIU 888 Web
interface is displayed. The Diagnostics window is displayed by
default (see FIGURE 1-5).
FIGURE 1-5 CIU 888 Web interface: Diagnostics window
Table of Contents
Sealing Guide Part No.: 4417595_Rev10
4 CIU 888
$*6
5. Click CONFIGURE in the section menu bar.
The Configure window is displayed (see FIGURE 1-6).
FIGURE 1-6 CIU 888 Web interface: Configuration window
The Configuration windows displays the global settings and internal
SI units that have been configured for the CIU 888, and indicates for
each global setting whether it is W&M relevant or not. Furthermore,
the Configuration window provides for each site element (tank, port,
gauge) in the site tree an overview of the configuration settings. For
each configuration setting the configured value is displayed, and
whether the configuration setting is W&M relevant or not.
6. Verify if all W&M relevant configuration settings have been
configured correctly. Configuration settings that have not been
configured correctly need to be re-configured.
NOTE: Refer to the Configuration Manual CIU 888 (Part No. 4417593) for more
information about changing the configuration settings of the CIU 888.
1. CONFIGURE option
2. Site tree
3. Configuration settings
1
2
3
Autres manuels pour CIU 888
8
Table des matières
Autres manuels Honeywell Porte
Honeywell
Honeywell NS1 Manuel utilisateur
Honeywell
Honeywell Lyric LCP300-L Manuel d'installation et d'exploitation
Honeywell
Honeywell W7006A Manuel utilisateur
Honeywell
Honeywell LyricLCP300-L Manuel d'installation et d'exploitation
Honeywell
Honeywell SMX Manuel utilisateur
Honeywell
Honeywell NOTIFIER NFN-GW-PC-W Manuel utilisateur
Honeywell
Honeywell Experion PKS Manuel utilisateur
Honeywell
Honeywell PEHA 940/8 DALI-G Manuel utilisateur
Honeywell
Honeywell HON-CGW-MBB Manuel utilisateur
Honeywell
Honeywell CIU 888 Manuel d'utilisation
Honeywell
Honeywell Wireless Network Master ETH/WIFI T2 Manuel utilisateur
Honeywell
Honeywell RFG100 Manuel utilisateur
Honeywell
Honeywell Notifier MODBUS-GW Manuel utilisateur
Honeywell
Honeywell RedLINK THM6000R Manuel utilisateur
Honeywell
Honeywell 290092 Manuel utilisateur
Honeywell
Honeywell NOTIFIER ONYXWorks NFN Gateway Manuel utilisateur
Honeywell
Honeywell ADPRO iFT Series Manuel utilisateur
Honeywell
Honeywell Notifier 002-467 Manuel utilisateur
Honeywell
Honeywell NFS-3030 Manuel utilisateur
Honeywell
Honeywell GW-1000-WE Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
