Honeywell DirectLine DL423 Manuel utilisateur

DirectLine®DL423 Sensor Module

for Conductivity/Resistivity Measurements

User Manual

70-82-25-112

Rev. 3

September 2011

Honeywell Process Solutions

Notices and Trademarks

September, 2011

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty

workmanship. Contact your local sales office for warranty information. If warranted goods are

returned to Honeywell during the period of coverage, Honeywell will repair or replace without

charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all

other warranties, expressed or implied, including those of merchantability and fitness for a

particular purpose. Specifications may change without notice. The information we supply is

believed to be accurate and reliable as of this printing. However, we assume no responsibility for

its use.

While we provide application assistance personally, through our literature and the Honeywell

web site, it is up to the customer to determine the suitability of the product in the application.

CE Conformity

This product is in conformance with the protection requirements of the following European

Council Directives: 89/336/EEC, the Electromagnetic Compatibility Directive and 73/23/EEC,

the Low Voltage Directive. Conformance of this product with any other “CE Mark” Directive(s)

shall not be assumed.

ATTENTION

The emission limits of EN 61326 are designed to provide reasonable protection against harmful

interference when this equipment is operated in an industrial environment. Operation of this

equipment in a residential area may cause harmful interference. This equipment generates, uses

and can radiate radio frequency energy and may cause interference to radio and television

reception when the equipment is used closer than 30 m to the antenna(e). In special cases, when

highly susceptible apparatus is used in close proximity, the user may have to employ additional

mitigating measures to further reduce the electromagnetic emissions of this equipment.

Honeywell Process Solutions

Honeywell

512 Virginia Drive

Fort Washington, PA 19034

DirectLine is a trademark of Honeywell

Other brands or product names are trademarks of their respective owners

ii DirectLine® DL423 Sensor Module User Manual 9/11

About This Document

Abstract

This manual contains all the information that is needed to install, configure, calibrate,

operate, and troubleshoot the DirectLine®Sensor. Insert 70-82-10-03, a quick

reference guide for configuring and calibrating the DL423, should accompany this

document.

Contacts

World Wide Web

The following lists Honeywell’s World Wide Web sites that will be of interest to our

customers.

Honeywell Organization WWW Address (URL)

Corporate http://www.honeywell.com

Honeywell Process Solutions https://www.honeywellprocess.com

Telephone

Organization Phone Number

United States and

Canada Honeywell 1-800-423-9883 Tech. Support

1-888-423-9883 Q&A Faxback

(TACFACS)

1-800-525-7439 Service

Symbol Definitions

The following table lists any symbols used in this document to denote certain conditions.

Symbol Definition

Earth Ground. Functional earth connection. NOTE: This connection shall be bonded to

Protective earth at the source of supply in accordance with national and local electrical

code requirements.

9/11 DirectLine® DL423 Sensor Module User Manual iii

Contents

1. INTRODUCTION....................................................................................................................1

1.1 Overview.........................................................................................................................................1

1.2 Electronics Module .........................................................................................................................1

1.3 Operator Interface...........................................................................................................................2

1.4 Specifications..................................................................................................................................2

1.5 Model Selection Guide ...................................................................................................................4

2. INSTALLATION.....................................................................................................................6

2.1 Assembly and Wiring......................................................................................................................6

2.2 Mounting.........................................................................................................................................8

2.3 Conduit connections.....................................................................................................................11

3. CONFIGURATION...............................................................................................................12

3.1 Overview.......................................................................................................................................12

3.2 Configuration Set Up Procedure...................................................................................................14

4. CALIBRATION.....................................................................................................................18

4.1 Calibration.....................................................................................................................................18

5. OPERATION........................................................................................................................21

5.1 Displays........................................................................................................................................21

5.2 Diagnostic Error Messages ..........................................................................................................23

5.3 Unit Reset.....................................................................................................................................24

6. SPARE PARTS....................................................................................................................25

7. APPENDIX: CE MARK APPLICATIONS ............................................................................26

8. SALES AND SERVICE........................................................................................................27

iv DirectLine® DL423 Sensor Module User Manual 9/11

Tables

Table 2-1 Assembly and Wiring Procedure for Field Wiring Connector__________________________ 7

Table 2-2 Remote Mounting Procedure for Conductivity Cells ________________________________ 8

Table 2-3 Conductivity Cell Remote Connections _________________________________________ 10

Table 3-1 Configuration Set Up Procedure ______________________________________________ 14

Table 4-1 Calibration Procedure ______________________________________________________ 18

Table 5-1 Online Parameter Descriptions _______________________________________________ 21

Table 5-2 Display Navigation Procedure ________________________________________________ 22

Table 5-3 Online Diagnostic Errors ____________________________________________________ 23

Table 5-4 Factory Default Values _____________________________________________________ 24

9/11 DirectLine® DL423 Sensor Module User Manual v

vi DirectLine® DL423 Sensor Module User Manual 9/11

Figures

Figure 1-1 Electronics Module_________________________________________________________ 1

Figure 2-1 Cordset Connection and Wiring _______________________________________________ 6

Figure 2-2 Field Wiring Connector______________________________________________________ 7

Figure 2-3 Remote Mounting__________________________________________________________ 9

Figure 2-4 Remote Mounting Hardware_________________________________________________ 11

Figure 7-1 Wiring for CE Mark Applications______________________________________________ 26

Introduction

9/11 DirectLine® DL423 Sensor Module User Manual 1

1. Introduction

1.1 Overview

The DirectLine® Sensor consists of an electronics module connected to a

Conductivity Cell.

The electronics module is contained in a NEMA Type 4x sealed weatherproof,

corrosion/impact-resistant polysulfone housing that can be mounted at the end of an

immersion tube or in a sample line. The sealed plastic housing has plug-in

connections for the conductivity cells and 4-20 mA cordset.

1.2 Electronics Module

The electronics module is loop-powered by 16-42 Vdc and will modulate its supply

current from 4 mA to 20 mA, depending upon the conductivity value that is sensed

by the cell. The transmitted loop current is compensated for temperature internally

using the standard Honeywell 8550 thermistor.

For submersion or special wiring applications, the remote electronics module is

compatible with a remote cable/connector that allows the electronics module to be

Wall. Pipe, or DIN Rail mounted.

A 4-20 mA output connection is provided via a 6m cordset or a customer supplied

cable used in combination with a field wiring connector.

Figure 1-1 Electronics Module

Introduction

2 DirectLine® DL423 Sensor Module User Manual 9/11

1.3 Operator Interface

The DirectLine® Sensor operator interface consists of three pushbuttons and one 4-

digit, 7-segment LCD display with 3 decimal points, plus (+), and minus (–) signs. It

is responsible for the display of measured values and configuration of parameter

values.

1.4 Specifications

Display Ranges Conductivity: 0 to 2000 S/cm, 0 to 20.00 mS/cm,

0 to 1000 mS/cm

Resistivity: 0 to 20.00 M-cm

Total Dissolved Solids (TDS): 0 to 2000 ppm,

0 to 2000 ppb, 0 to 200ppt

% Concentration: 0 to 20.00%

Displayed Temperature Range –10 °C to +140 °C (14 °F to 284 °F)

Display Accuracy Conductivity/Resistivity: Greater of +/- 2 counts or

+/- 0.5% of reading

Concentration: +/- 0.5% of reading

Temperature: +/- 0.1°C from –10 to 99.9°C,

+/- 1°C from 100 to 140 °C

Display Resolution 4 digits, floating decimal point

Process Temperature

Model 4973/4905

DL4000

–10 °C to +140 °C (14 °F to 284 °F)

0 °C to 65 °C (32 ° F to 149 °F)

Electronics Module Ambient

Temperature –20 °C to +85 °C (–4 °F to +185 °F)

Output Type 4-20 mA (2-wire loop powered)

Output Calibration 4-20 mA

Cell Constant/Cell Calibration

Factor Input Automatic from EEPROM in Conductivity Cell (for

4973/4905 type cells only)

Manual input for DL4000 type cells

Output (Loop) 6m (19.7’) cordset or shielded twisted pair with

field wiring connector

Output (Loop) User Termination Tinned leads

Introduction

9/11 DirectLine® DL423 Sensor Module User Manual 3

Cable Lengths Remote Sensor:

Integral Cable

Quick Disconnect

6m (19.7’) (cable integral to conductivity cell)

2m (6.56'), 3m (9.84'), 6m (19.69') and 15m

(49.21')

Power 16-42 Vdc, 23mA max

Maximum load resistance: 250 ohms at 16 Vdc

600 ohms at 24 Vdc

1400 ohms at 42 Vdc

Local Display and Buttons LCD 4-digit, 7-segment

Engineering Units (Labels) S/cm, mS/cm, M-cm, ppm TDS, ppb TDS, ppt

TDS, %NaOH, %HCl, %NaCl, %H2SO4

Calibration Options Cal Trim Factor, 1 Point Cal Solution

Solution Temperature

Compensation Acid (Cation/Ammonia), Salt (Neutral Salts),

NaCl, HCl, NaOH, H2SO4, and None (for USP24

Conformance)

Diagnostics Sensor and electronics

Case Weatherproof, corrosion/impact-resistant housing,

IP66

Approvals CE Mark - for Industrial Applications

UL – General Purpose for Process Control

CSA - General Purpose

FM Class1, Div. 1 (I.S.)

FM Class 1, Div. 2 (non-incendive field wiring)

Remote Mounting Pipe, Wall, or DIN Rail

Dimensions H 123 mm (4.84”) x W 48 mm (1.89”) x D 46 mm

(1.81”)

Weight Approximately 142 g (5.0 oz.)

Introduction

4 DirectLine® DL423 Sensor Module User Manual 9/11

1.5 Model Selection Guide

Instructions

Select the desired key number. The arrow to the right marks the selection available.

Make the desired selections from Tables I through IV using the column below the

proper arrow. A dot ( ) denotes availability.

Key Number I II III IV

_ _ _ _

Key Number - DirectLine

Sensor Electronics Module

(Specify electrodes/cells/probes separately) Selection

pH For use with Durafet II, Meredian II & HPW7000 pH electrodes DL421

ORP For use with ORP electrode. DL422

Conductivity For use with Contacting Conductivity Cells DL423

DO - PPM For use with Dissolved Oxygen ppm Probes DL424

DO - PPB For use with Dissolved Oxygen ppb Probes

TABLE I - OUTPUT CABLE

Cordset - 6m (19.7 ft.) - includes connector and cable - Note 2 E

Field Wiring Connector only - customer supplies cable only-Note 2

TABLE II - SENSOR CABLE/REMOTE CONNECTOR (between electronic module and electrode, sensor or pr

0ddddd

6,096m (20 ft.) of sensor cable - Durafet II Remote Mounting 1 e

15,24m

(

50 ft.

)

of sensor cable - Durafet II Remote Mountin

eeee

TABLE III - REMOTE MOUNTING OPTIONS

None Integral unit - mounting not required A

2" (5,08 cm) Pipe mtg. bracket, wall mtg, & DIN Rail clip B

TABLE IV - OPTIONSNone 00 _ _

Linen Customer ID Tag - 3 lines w/22 characters/line LT _ _

SS Customer ID Tag - 3 lines w/22 character/line SS _ _

Certificates None _ _ 00

Calibration & Conformance _ _ CC

Mounting Kit for

Remote Mounting

None(replacement module or customer supplied output cable)-Note 1 D

Remote Mounting Connector - Meredian II ORP

Remote Mounting Connector - HPW7000

Remote Mounting Connector - Conductivity

Remote Mounting Connector - Dissolved Oxygen

DL425

Remote Mounting Connector - Meredian II pH

Remote Mounting

Connector (Cable is

supplied with sensor or

probe)

Integral Mounting No cable or connector required

Remote Mounting Cable

- Durafet only

Availability

Output Cable for

Integral or Remote

Mounting F

_ _ _

Tagging

Notes:

1Customer supplies cordset o

cable with M12 connecter. Suppliers & P/Ns include:

Phoenix Contact Turck

Cord--set SAC-3P-5.0-PUR/M12FSSH Stainless RKV4T-6/S618

M12 Field Wiring Connector SACC-M12FS-4CON-PG7 B8141-0

Cable

2Recommended cable is 2-wire twisted shielded pair

RESTRICTIONS

Table

ORDERING INSTRUCTIONS:

1. Part numbers are provided to facilitate Distributor Stock.

2. Orders may be placed either by model selection or by part number.

3. Part numbers are shown within the model selection tables to assist with compatibility information.

4. Orders placed by model selection are systematically protected against incompatibility.

5. Compatibility assessment is the responsibility of the purchaser for orders placed by part number.

6. Items labeled as N/A are not available via the stocking program and must be ordered by model selection.

III B

Available OnlyWith Not Available With

IIl A

Selection Table

2-wire twisted shielded pair

Restriction

Letters Selection

Table des matières

Autres manuels Honeywell Unité de contrôle

Honeywell

Honeywell PRO32OUT Manuel utilisateur

Honeywell

Honeywell V4730B Manuel utilisateur

Honeywell

Honeywell NOTIFIER FCM-1 Manuel utilisateur

Honeywell

Honeywell RF CM61NG Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell BCU 370 Manuel

Honeywell

Honeywell Braukmann RV 284 Manuel utilisateur

Honeywell

Honeywell AlarmNet 7847i-E Instructions de montage

Honeywell

Honeywell SUPER TRADELINE VR8300A Manuel utilisateur

Honeywell

Honeywell Ex-Or CDW12U5 Manuel d'installation et d'exploitation

Honeywell

Honeywell NOTIFIER FTM-1 Manuel utilisateur

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manuel utilisateur

Honeywell

Honeywell HM700AFVALVE Manuel utilisateur

Honeywell

Honeywell LTE-L57V Manuel utilisateur

Honeywell

Honeywell S7800A Manuel utilisateur

Honeywell

Honeywell FV300 Caractéristiques techniques

Honeywell

Honeywell Gamewell FCI Velociti Series Manuel utilisateur

Honeywell

Honeywell DirectConnect AMX300 Manuel utilisateur

Honeywell

Honeywell PEHA PHC Manuel utilisateur

Honeywell

Honeywell HS10S Manuel utilisateur

Honeywell

Honeywell BCU 460 Manuel

Honeywell

Honeywell VR4920Z 1000 Manuel utilisateur

Honeywell

Honeywell MI-DCMOE Mode d’emploi

Honeywell

Honeywell AVS Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur