Honeywell 3800 Linear Series Manuel utilisateur

3800 Linear Series

Quick Start Guide

EN-1

Note: Refer to your user’s guide for information

about cleaning your device.

Getting Started

Turn off computer’s power before connecting the

scanner, then power up the computer once the

scanner is fully connected.

USB Connection

EN-2

Keyboard Wedge Connection

Serial (RS-232) Connection

Note: Does not apply to the 3800g Lite Plus.

EN-3

Reading Techniques

The view finder

projects a red

aiming beam that

should be

centered over the

bar code.

Hold the scanner

over the bar code,

pull the trigger,

and center the

aiming beam on

the bar code.

The aiming beam is smaller when the scanner is

closer to the code and larger when it is farther from

the code. Hold the scanner close to smaller bar

codes, and farther away from large bar codes to get

a proper read.

If the bar code is highly reflective (e.g., laminated),

you may need to tilt the scanner at an angle so the

bar code can be scanned.

EN-4

To read PDF417 bar codes with a PDF-enabled

3800, hold the trigger down and move the scanner

up and down so the aiming line sweeps from the top

of the bar code to the bottom, and back up.

This ensures that the entire code is scanned.

Note: This only applies to a PDF enabled 3800/

3800g.

Standard Product Defaults

The following bar code resets all standard product

default settings.

Standard Product Defaults

EN-5

Interface

Scan the bar code that describes the PC or

interface you are using.

AT/PS2 Keyboard Wedge

(Default)

RS-232

(Does not apply to 3800g Lite Plus)

USB Keyboard (PC)

Emulate External Keyboard

EN-6

Keyboard Country

Scan the Program Keyboard Country bar code

below, then scan the numeric bar code(s) from

page EN-10, then the Save bar code to program the

keyboard for your country. As a general rule, the

following characters are not supported by the

scanner for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~.

Note: For a complete list of country codes, see the

User’s Guide for your product at our website,

www.honeywell.com/aidc.

Country Code Scan Country Code Scan

Belgium 1 Italy 5

Denmark 8 Norway 9

Finland 2 Spain 10

France 3 Switzerland 6

Germany/Austria 4 USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

EN-7

Trigger

The following bar codes will allow you to use the

reader in Manual Trigger mode (need to press the

trigger to read), Automatic Trigger mode (the beam

is always on), or Presentation mode (the reader is

activated when it “sees” a bar code).

Reread Delay

This sets the time period before the scanner can

read the

same

bar code a second time. Setting a

reread delay protects against accidental rereads of

the same bar code.

Manual Trigger

(Default)

Automatic Trigger

Presentation Mode

Medium Reread Delay

for 3800 only

Medium Reread Delay

for 3800g, 3800g Lite Plus, 3800r, and 3800i

EN-8

Suffix

If you want a carriage return after the bar code,

scan the Add CR Suffix bar code. To add a tab

after the bar code, scan the Add Tab Suffix bar

code. Otherwise, scan the Remove Suffix bar

code to remove the suffixes.

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a

Code ID prefix to all symbologies at once.

Note: For a complete list of Code IDs, see the

User’s Guide for your product at our website,

www.honeywell.com/aidc.

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix To All Symbologies

(Temporary)

Autres manuels pour 3800 Linear Series

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Honeywell Lecteur de codes-barres

Honeywell

Honeywell Genesis 7580G Manuel utilisateur

Honeywell

Honeywell Voyager 1450g Series Manuel utilisateur

Honeywell

Honeywell MK3480-30B104 - IS3480 QuantumE - Wired Desktop Barcode... Manuel utilisateur

Honeywell

Honeywell IT3800 Manuel utilisateur

Honeywell

Honeywell 3800r Manuel utilisateur

Honeywell

Honeywell Vuquest 3310g Manuel utilisateur

Honeywell

Honeywell XENON 1902G-BF Manuel utilisateur

Honeywell

Honeywell HH490 Manuel utilisateur

Honeywell

Honeywell 4850DR Manuel utilisateur

Honeywell

Honeywell XENON 1900 Manuel utilisateur

Honeywell

Honeywell MS4980 Manuel utilisateur

Honeywell

Honeywell MX7 Tecton Manuel utilisateur

Honeywell

Honeywell Voyager 1202G Manuel utilisateur

Honeywell

Honeywell VOYAGER 1250G Manuel utilisateur

Honeywell

Honeywell BTRS-QS Manuel utilisateur

Honeywell

Honeywell Horizon MS7600 Manuel utilisateur

Honeywell

Honeywell Hyperion 1300G Manuel utilisateur

Honeywell

Honeywell Granit 1280i Manuel utilisateur

Honeywell

Honeywell XENON 1902G-BF Dimensions

Honeywell

Honeywell 5010 Manuel utilisateur

Honeywell

Honeywell 3800G04-USBKITE Manuel utilisateur

Honeywell

Honeywell MS9535-5 Manuel utilisateur

Honeywell

Honeywell Solaris MS7820 Manuel utilisateur

Honeywell

Honeywell Orbit MS7120 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur