Holtek BC66F2332-1 Manuel utilisateur

BC66F2332-1 Easy DEV User Guide

Revision: V1.00 Date: February 20, 2023

Rev. 1.00 2 February 20, 2023 Rev. 1.00 3 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

Table of Contents

1. General Description......................................................................................... 3

1.1 Main Features ........................................................................................................................3

1.2 Hardware Introduction............................................................................................................3

2. e-Link On-Chip Debug Support – OCDS........................................................ 4

2.1 Software Introduction .............................................................................................................4

2.2 Hardware Introduction............................................................................................................4

3. e-Link In Circuit Program Function – ICP...................................................... 6

3.1 Software Introduction .............................................................................................................6

3.2 Hardware Introduction ...........................................................................................................6

4. Pin and Schematics......................................................................................... 8

4.1 Pin Assignment – Size: 20mm×64mm ...................................................................................8

4.2 Schematic ..............................................................................................................................8

Rev. 1.00 2 February 20, 2023 Rev. 1.00 3 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

1. General Description

1.1 Main Features

• Directly connects to the e-Link without need for wiring

• Connects to the e-Socket (ESKT40DIPC) for programming using the e-WriterPro

• Three power supply options: 5V (USB)/3.3V/VDD (e-Link)

• Preload breathing lamp (LED) DEMO CODE, development board status is convenient for

inspection

• Compact board – PAD hole distance multiple of 100mil allows for convenient usage

1.2 Hardware Introduction

e-Link Interface

Micro USB

OCDS or ICP Selection

I/O Port

Power Selection

Antenna Connector

LED Switch

I/O Port

OCDS EV

BM2302-64-2 Module

SMA Connector

OCDS or ICP Selection

Note: 1. The development board only supports 433.93MHz frequency band.

2. If the SMA connector is used, select the 50Ω impedance antenna.

3. If use the spring antenna attached to the board, change the R3 to the R5 and weld the

antenna to E1 point.

Rev. 1.00 4 February 20, 2023 Rev. 1.00 5 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

2. e-Link On-Chip Debug Support – OCDS

2.1 Software Introduction

1. Download the software from the Holtek ocial website to obtain the relevant information.

Download Path: MCU Development Tools – Software – ICE Software – HT-IDE3000

2. After the HT-IDE3000 installation has completed, the Holtek HT8OCDS-ICE User’s Guide can

be accessed from its menu.

3. Update the e-Link to e-Link OCDS Mode using the HT-IDE3000 software.

2.2 Hardware Introduction

1. e-Link HT8OCDS Pin Assignment

Rev. 1.00 4 February 20, 2023 Rev. 1.00 5 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

2. Hardware Connection Schematic Diagram

USB

The jumper socket

closed to the OCDSDA

OCDS The jumper socket

closed to the OCDSCK

Connects to the USB port for programming using the HT-IDE3000. If problems are encountered,

refer to the HT-IDE3000 User’s Guide.

• If the connection is successful, the following message will pop up:

• If the connection fails or there is no connection, the following message will pop up:

Rev. 1.00 6 February 20, 2023 Rev. 1.00 7 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

3. e-Link In Circuit Program Function – ICP

3.1 Software Introduction

1. Download the software from the Holtek ocial website to get the relevant information.

Download Path: MCU Development Tools – Software – Programmer Software – HOPE3000 for

e-Link

2. After the HOPE3000 for e-Link installation has completed, the User’s Guide can be accessed

from the menu.

3. Update the e-Link to the e-Link ICP mode using the HOPE3000 for e-Link software.

3.2 Hardware Introduction

1. e-Link ICP Pin Assignment

Rev. 1.00 6 February 20, 2023 Rev. 1.00 7 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

2. Hardware Connection Schematic Diagram

USB

The jumper socket closed to the ICPDA

The jumper socket closed

the ICPCK

ICP

Connects to the USB port for programming using the HOPE3000 for e-Link. If the connection is

successful, a prompt will be generated informing the user that the writer is connected. If problems

are encountered, refer to the HOPE3000 for e-Link User’s Guide.

Rev. 1.00 8 February 20, 2023 Rev. 1.00 9 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

4. Pin and Schematics

4.1 Pin Assignment – Size: 20mm×64mm

PA6

PA5

PA7

PA4

PA0

PA1

PA2

PA3

[STCK0]

STP0I

STP0B

VDD

AN3 INT

INT

ICPCK

RES

ICPCK

OCDSCK OCDSDA

ICPDA

INT

INT AN2

AN1

AN3 STP0

STP0B

STP0

[STP0I]

VREF

VREFO

ICPDA

GND

4.2 Schematic

Rev. 1.00 8 February 20, 2023 Rev. 1.00 9 February 20, 2023

BC66F2332-1 Easy DEV User Guide BC66F2332-1 Easy DEV User Guide

The information provided in this document has been produced with reasonable

care and attention before publication, however, HOLTEK does not guarantee

that the information is completely accurate. The information contained in this

publication is provided for reference only and may be superseded by updates.

HOLTEK disclaims any expressed, implied or statutory warranties, including but

not limited to suitability for commercialization, satisfactory quality, specications,

characteristics, functions, tness for a particular purpose, and non-infringement of

any third-party’s rights. HOLTEK disclaims all liability arising from the information

and its application. In addition, HOLTEK does not recommend the use of

HOLTEK’s products where there is a risk of personal hazard due to malfunction

or other reasons. HOLTEK hereby declares that it does not authorise the use of

these products in life-saving, life-sustaining or safety critical components. Any use

of HOLTEK’s products in life-saving/sustaining or safety applications is entirely

at the buyer’s risk, and the buyer agrees to defend, indemnify and hold HOLTEK

harmless from any damages, claims, suits, or expenses resulting from such use.

The information provided in this document, including but not limited to the content,

data, examples, materials, graphs, and trademarks, is the intellectual property

of HOLTEK (and its licensors, where applicable) and is protected by copyright

law and other intellectual property laws. No license, express or implied, to any

intellectual property right, is granted by HOLTEK herein. HOLTEK reserves the

right to revise the information described in the document at any time without prior

notice. For the latest information, please contact us.

Table des matières

Autres manuels Holtek Microcontrôleur

Holtek

Holtek HT49RU80 Manuel utilisateur

Holtek

Holtek HT67F2350 Manuel utilisateur

Holtek

Holtek HT16C22 Instructions d'utilisation

Holtek

Holtek HT46RU67 Manuel utilisateur

Holtek

Holtek HT32 Mode d’emploi

Holtek

Holtek HT32F54231 Manuel utilisateur

Holtek

Holtek HT48RA5 Manuel technique

Holtek

Holtek HT45R36 Manuel de référence

Holtek

Holtek HT66F20-1 Manuel utilisateur

Holtek

Holtek HT48R10A-1 Manuel utilisateur

Holtek

Holtek HT46R74D-1 Manuel technique

Holtek

Holtek HT49RA0 Manuel utilisateur

Holtek

Holtek HT49R30A-1 Manuel utilisateur

Holtek

Holtek HT46R003B Manuel utilisateur

Holtek

Holtek HTG2190 Manuel utilisateur

Holtek

Holtek HT66F20 Manuel utilisateur

Holtek

Holtek HT66F488 Manuel utilisateur

Holtek

Holtek HT46R46 Manuel utilisateur

Holtek

Holtek BS86DH12C Manuel utilisateur

Holtek

Holtek BS83A04C Manuel utilisateur

Holtek

Holtek HT46RU75D-1 Manuel utilisateur

Holtek

Holtek BS82B12A-3 Manuel utilisateur

Holtek

Holtek HT66F60A Manuel utilisateur

Holtek

Holtek HT32F52220 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur