HMS Anybus Communicator IIoT Guide de l'utilisateur
Anybus®Communicator™
IIoT
STARTUP GUIDE
SP2444 1.0 en-US ENGLISH
Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB
of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We,
HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous
product development. The information in this document is subject to change without notice and should not
be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no
responsibility for any errors that may appear in this document.
There are many applications of this product. Those responsible for the use of this device must ensure that
all the necessary steps have been taken to verify that the applications meet all performance and safety
requirements including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems
that may arise as a result from the use of undocumented features, timing, or functional side effects found
outside the documented scope of this product. The effects caused by any direct or indirect use of such
aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular implementation, HMS Industrial Networks
AB cannot assume responsibility for actual use based on these examples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product
described in this document. These intellectual property rights may include patents and pending patent
applications in the USA and other countries.
Anybus®is a registered trademark of HMS Industrial Networks AB. All other trademarks mentioned in this
document are the property of their respective holders.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Preface 3 (12)
1 Preface
1.1 About This Document
This document describes how to install the Anybus Communicator IIoT.
For additional documentation and software downloads, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
1.2 Document Conventions
The following formatting conventions are used in this document to indicate safety
information and other content of specific importance:
WARNING
This instruction must be followed to avoid a risk of death or serious injury.
Caution
This instruction must be followed to avoid a risk of personal injury.
This instruction must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
This is additional information which may facilitate installation and/or
operation.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Installation 4 (12)
2 Installation
2.1 Installation Overview
Prerequisites
The following items are required for installation and basic configuration:
• Configuration cable
• Subnetwork cable
• Ethernet cable
• Anybus Configuration Manager - Communicator RS-232/422/485
(4.5.0.0 or later)
• Anybus Configuration Manager - IIoT
• IPconfig (3.2.1.1 or later)
The Anybus Configuration Manager and IPconfig applications can be
downloaded from www.anybus.com/support.
Basic installation steps
1. Mount the Anybus Communicator on the DIN rail.
2. Connect the serial and IIoT network interfaces.
3. Connect the configuration cable between the gateway and a PC.
4. Connect the power cable and apply power.
5. Check the LED indicators to verify that the gateway is running and that the
serial and IT networks are connected. See LED Indicators, p. 9.
6. Use Anybus Configuration Manager - Communicator to set up the data
exchange configuration in the Anybus Communicator.
7. Use IPconfig to configure the TCP/IP settings for the Anybus Communicator.
8. Use Anybus Configuration Manager - IIoT to create a tag configuration and
transfer it to the Anybus Communicator.
9. Connect to the web interface of the Anybus Communicator and configure
MQTT/OPC UA communication.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Installation 5 (12)
2.2 DIN Rail Mounting
The unit must be electrically grounded through the DIN rail for EMC
compliance.
Mount on DIN rail
Fig. 1 Push down to mount or remove
1. Hook the unit onto the upper lip of the rail and push gently downwards.
2. Push the unit towards the rail until it snaps into place.
Remove from DIN rail
1. Push the unit gently downwards on the rail.
2. Pull the bottom end of the unit free of the rail and remove it.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Installation 7 (12)
2.3.2 Serial Subnetwork Interface
Fig. 3 D-sub connector (DE-9F)
Pin Description RS-232 RS-422 RS-485
1 +5 V Output (100 mA max.) xxx
2 RS-232 Rx x
3 RS-232 Tx x
4(reserved)
5Signal Ground xxx
6 RS-422 Rx + x
7RS-422 Rx - x
8 RS-485 + / RS-422 Tx + x x
9 RS-485 - / RS-422 Tx - x x
Housing Shield xxx
Do not connect Signal Ground to Protective Earth (PE) of other nodes on
the subnetwork as this may damage the on-board serial transceivers.
Connect it only to the Signal Ground on other nodes.
Bias and/or termination resistors may be required depending on the type of
serial network. Please refer to the User Manual for more information.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Installation 8 (12)
2.3.3 Power Connector (2 pin)
Connecting power with reverse polarity or using the wrong type of power
supply may damage the equipment. Make sure that the power supply is
connected correctly and of the recommended type.
Pin Signal
1 +24 VDC
2 Power Ground
2.3.4 PC Connector (RJ11)
Pin Signal
1 GND ( signal ground)
2 GND (signal ground)
3 RS-232 Rx (input)
4 RS-232 Tx (output)
2.3.5 Ethernet Connector (RJ45)
Pin Signal Description
1 TD+ Transmit data +
2 TD- Transmit data -
3 RD+ Receive data +
6 RD- Receive data -
4,5,7,8 -(reserved)
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Installation 9 (12)
2.4 LED Indicators
1 2
3
5
4
6
LED 1 to 4 Model-specific information
LED 5 Serial subnetwork status
LED 6 Device status
LED Indication Meaning
1 - Network Status
Off Offline or no power
Green Online, IP address assigned
Green, flashing No IP address assigned or no link
Red Fatal error, IP address conflict
Alternating Red/Green Firmware update in progress
2 - Module Status
Off No power or IP address conflict
Green Normal operation
Red Fatal error
Alternating red/green Firmware update in progress
3 - Link/Activity 1
4 - Link/Activity 2
Off Link not detected or no power
Green Link established (100 Mbit/s)
Green, flickering Link activity (100 Mbit/s)
Red Link established (10 Mbit/s)
Red, flickering Link activity (10 Mbit/s)
5 - Subnet Status Off No power
Green Running
Green, flashing Running, one or more transaction
errors
Red Transaction error/timeout or subnet
stopped
6 - Device Status Off No power
Green Initializing
Green, flashing Running
Red Bootloader mode
Alternating red/green Configuration invalid or missing
The Link/Activity LED indicators will show a red light for 10 Mbit/s connections.
This is normal and does not indicate an error.
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Technical Data 10 (12)
3 Technical Data
3.1 General Specifications
Model name Anybus Communicator IIoT
Order code AB7079-B
Dimensions (L x W x H) 120 x 75 x 27 mm
Weight 150 g
Operating temperature 0 to +55 °C (IEC 60068-2-1 and IEC 60068-2-2)
Storage temperature -40 to +85 °C (IEC 60068-2-1 and IEC 60068-2-2)
Humidity range 5–95 % RH, non-condensing (IEC 60068-2-30)
Power supply 24 V ±10 % DC regulated power source
Current consumption Typical: 100 mA @ 24 VDC
Maximum: 200 mA @ 24 VDC
Galvanic isolation Yes, on both network sides
Mechanical rating IP20, NEMA rating 1
Mounting DIN rail (EN 50022)
Network shield conductance via DIN rail
Certifications See datasheet at www.anybus.com/support
3.2 Serial Interface
Serial application Interface Selectable RS-232, RS-422, RS-485
Maximum number of stations 31 nodes via RS-422 or RS-485
Protocol: Modbus RTU Modbus RTU Master - Query/Response
Protocol: ASCII/Vendor Specific Request/Response or Produce/Consume
Protocol: Rockwell DF1 DF1 Master
Anybus®Communicator™Startup Guide SP2444 1.0 en-US
Table des matières
Autres manuels HMS Porte
HMS
HMS IXXAT CANbridge Manuel utilisateur
HMS
HMS Anybus Modbus-TCP/RTU Gateway Manuel utilisateur
HMS
HMS Netbiter EasyConnect Manuel utilisateur
HMS
HMS Intesis INBACSAM004O000 Manuel utilisateur
HMS
HMS AnyBus-X AB7607 Manuel utilisateur
HMS
HMS Intesis WMP Manuel utilisateur
HMS
HMS AnyBus-X J1939 Manuel utilisateur
HMS
HMS AB9008 Manuel utilisateur
HMS
HMS Anybus HMS-EN2MB-R Manuel utilisateur
HMS
HMS Intesis INKNXMBM1000100 Instructions de montage
HMS
HMS Intesis WMP Manuel utilisateur
HMS
HMS eWON Netbiter EC300 Series Manuel utilisateur
HMS
HMS Ixxat SG-gateway Guide de l'utilisateur
HMS
HMS AnyBus-X J1939 Manuel utilisateur
HMS
HMS Anybus X-gateway CANopen Manuel utilisateur
HMS
HMS Intesis INMBSHIS016O000 Manuel utilisateur
HMS
HMS Intesis KNX - Hisense VRF Manuel utilisateur
HMS
HMS Netbiter EasyConnect EC220 Fiche technique
HMS
HMS Anybus-X AB7609 Manuel utilisateur
HMS
HMS Ixxat CAN@net NT 420 Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
