Hitachi CMP420V1 Manuel utilisateur

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

Plasma Display

August 2004 Digital Media Division

YK No.009E-1

SERVICE MANUAL

Be sure to read this manual before servicing. To assure safety from ﬁre, electric shock, injury, harmful radiation

and materials, various measures have been provided for in this HITACHI Plasma displayservice manual.

Be sure to read all cautionary items described in the manual to maintain safety before servicing.

Contents

1. Since the Panel Module and front Filter are made of glass, handlea broken Module and/or Filter with

sufficient care,in order not to be injured.

2.Repair work should not be started until after the Panel Module and the AC/DC Power supply have cooled

sufficiently.

3. Special care should be exercised in the proximity of the display area in order not to damage its surface.

4. The Panel Module should not be touched with bare hands, as this will protect its surface from stains.

5. It is recommended to use clean soft gloves during the repair work in order to protect not only the display

area of the Panel Module but also the technician.

6. The Chip Tube of the Panel Module (located in the upper left corner of the back of the glass panel)

is very fragile; as well, the flat cables connecting the Panel to the drive circuit PWBs are very weak. Take

care not to damage these, otherwise, the panel will never light again.

Service Warning

Caution

1. Features ----------------------------------------------- 3

2. Speciﬁcations----------------------------------------- 4

3. Component Names --------------------------------- 5

4. Service point ------------------------------------------ 6

5. Service Modes -------------------------------------7

6. Troubleshooting------------------------------------34

7. Block Diagram ------------------------------------37

CMP420V1/CMP420V2/42EDT41 (PW1A)

CAUTION FOR SAFETY

Please read this page before making repairs to themonitor.

This page explainscertain safety items found in this manual which are intended to ensure the

safety of the technician and to prevent accidents during any repair work.

Warning This symbol means "Personnel Electrical Safety Hazard"

Caution This symbol means "Equipment Operational Hazard"

This symbol means "CAUTION"

This symbol means "POSSIBILITY OF

ELECTRIC SHOCK"

This symbol means "DO IT!"

This symbol means "DON'TDO IT!"

Special Instructions

This indicates cabinet, chassis or parts

which require special attention.

Please follow any notesas well as all safety

precautions.

Prevent electrical shock

Please use care and caution when

servicing this product. High voltages

exist in the set which can cause injury

or death.

Please disconnect the AC power

during repair to prevent serious shock

or death.

Use only recommended components.

Please use the same characteristic compo-

nents, which is same as previous for your

safety. To ensure reliability,specially marked

Keep the same wiring dress for boards.

This monitor uses insulated spacers

which are intended to isolate metal

parts from electrical components.

Internal wiring is isolated from components by

using clamps, retainers, etc., so please return

to original condition for prevention of electrical

shock or fire.

Safety check should be done after finished.

Every part (removed screws, component

and wiring) should be returned to previous

condition.

Check around the repaired area for

any damage by mistake. Measure the

insulated impedance of AC by ohm meter.

Confirm that the value of impedance

is greater than 4M ohm.

It is possible for electric shock or fire to

occur if the value is less than 4M ohm.

Repair to the HDCP circuit is limited.

Never remove the shield case, which is

assembled to code with the HDCP circuit

WARNING

CMP420V1/CMP420V2/42EDT41 (PW1A)

PRECAUTIONS

●How to clean the plasma panel screen (front glass) of the monitor

Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.

To prevent scratching or damaging the plasma screen face, do not wipe the surface with sharp or hard

objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not

clean enough, then use a cloth with glass cleaner. Do not use any harsh or abrasive chemicals.

●How to clean the cabinet of the monitor

Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral

detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth.

Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax,

etc. because they could cause discoloration, scratches or cracks.

1. Features

●Large-screen, high-definition plasma display panel

The 42-inch color plasma display panel, with a resolution of 852 (H) x 480(V) pixels, creates a high-definition, large-

screen (aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic

sources and ambient power lines, the panel produces medium-quality images free from any color misconvergence

or corner focus distortion.

●High Performance Digital Processor

Awide range of personal computer signals can be handled, from 640 x 400, 640 x 480 VGA to 1600 x 1200 UXGA.

(RGB analog input)

●Easy-to-use remote control and on-screen-display system (OSD)

The remote control included eases the setting of display controls. Furthermore, the on-screen-display (OSD),

displays the input status control settings in an easy-to-view fashion.

●Power saving system

The International ENERGY STAR power saver feature saves power consumption automatically when input sig-

nals are not available.

When connected to a VESA DPMS-compliant PC, the monitor cuts its power consumption while it is idle.

●TruBass

TruBass, SRS and ( ) symbol are trademarks of SRS Labs,Inc.

TruBass technology is incorporated under license from SRS Labs, Inc.

CMP420V1/CMP420V2/42EDT41 (PW1A)

2. Specifications

Panel

Display

dimensions Approx. 42 inches (920 (H) x 518 (V) mm, diagonal 1059mm)

Resolution 852 (H) x 480 (V) pixels

Net dimensions

(excluding Speakers/Stand) 1030 (W) x 636 (H) x 91 (D) mm

Net weight

(excluding Speakers/Stand) CMP420V1/V2:33.2kg 42EDT41:34.2kg

Ambient

conditions

Temperature

Relative humidity Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)

Power supply AC100 - 240V, 50/60Hz

Power consumption/at standby 310W / <3W

Audio output

(RGB input)

Input signals

Input terminals

RGB1 DVI input terminal (DVI-D)

RGB1 audio input terminal (3.5mm Stereo Mini Jack)

RGB2 analog RGB input terminal (D-sub 15-pin)

RGB2 audio input terminal (3.5mm Stereo Mini Jack)

Video signals 0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)

480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60

Sync signals

H/V separate, TTL level [2K ]

H/V composite, TTL level [2K ]

Sync on green, 0.3 Vp-p [75 ]

(Video input)

(RF input)

Input signals

Input terminals

RF Video System

AV1: composite video input terminal (RCA)

AV1: Y PB PR video input terminal (RCA)

AV1: L/R audio input terminal (RCA)

AV2: composite video input terminal (RCA)

AV2: Y/G PB/B PR/R video input terminal (RCA)

AV2: L/R audio input terminal (RCA)

AV3: composite video input terminal (RCA)

AV3: S video input terminal (RCA)

AV3: L/R audio input terminal (RCA)

AV4: composite video / S video / RGB / L/R audio input terminal (Scart)

Video signals

AV1: NTSC-M, PAL-M, PAL-N

AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60

AV2: NTSC-M, PAL-M, PAL-N

AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB

AV3: NTSC-M, PAL-M, PAL-N

AV4: NTSC-M, PAL-M, PAL-N

NTSC-M

AV4: RGB

Video output Signal

OUTPUT (MONITOR): composite video monitor-output terminal (RCA)

OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)

AV4: composite video / L/R audio monitor-output terminal (SCART)

Operating : 5to 35, Storage : -15to 60

12W + 12W (6ǡ)

ANT : 75 unbalanced

Applicable video signals for each input terminal

Terminal RCA/SCART DVI D-sub

Signal CVBS S-video Component RGB PC STB RGB Component

AV1

AV2

AV3

AV4

RGB1

RGB2

( :Available)

CMP420V1/CMP420V2/42EDT41 (PW1A)

3. Component names

Remote-control

receiver

• Adjustment buttons are located

on the bottom.

• The back cover is provided with

indications to distinguish the

adjustment buttons.

Control panel

Main power switch

• The main power switch is located at the back, on the

lower surface.

Indicating lamp

for

CMP420V1

CMP420V2 for

42EDT41

[Remote control]

[Main unit]

CMP420V1/CMP420V2/42EDT41 (PW1A)

4. Service points

Lead free solder

This product uses lead free solder (unleaded) to help preserve the environment. Please read these

instructions before attempting any soldering work.

Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead

free solder can splatter at high temperatures (600˚C).

Lead free solder indicator

Printed circuit boards using lead free solder are engraved with an "F."

Properties of lead free solder

The melting point of lead free solder is 40-50˚C higher than leaded solder.

Servicing solder

Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.

Although servicing with leaded solder is possible, there are a few precautions that have to be taken. (Not

taking these precautions may cause the solder to not harden properly, and lead to consequent malfunctions.)

Precautions when using leaded solder

Remove all lead free solder from soldered joints when replacing components.

If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the

lead free solder has been completely melted (do not apply the soldering iron without solder).

Servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function) is recommended.

The melting point of lead free solder is higher than leaded solder. Use a soldering iron that maintains a high

stable temperature (large heat capacity), and that allows temperature adjustment according to the part being

serviced, to avoid poor servicing performance.

Recommended soldering iron:

Soldering iron with temperature control function (temperature range: 320-450˚C)

Recommended temperature range per part:

Part Soldering iron temperature

Mounting (chips) on mounted PCB 320˚C±30˚C

Mounting (chips) on empty PCB 380˚C±30˚C

Chassis, metallic shield, etc. 420˚C±30˚C

(1) FILTER PWB, SW PWB, LED/RECEIVER PWB, TACT SW PWB, SP TERMINAL(L/R) PWB

(2) AUDIO PWB, JOINT PWB

(3) VIDEO PWB

(4) FORMATTER PWB

(5) POWER BOARD

The PWB assembly which has used lead free solder

CMP420V1 / CMP420V2 / 42EDT41 (PW1A)

5. SERVICE MODE ACCESS

BURN-IN MODE

When the Burn-in feature is turned ON, the plasma panel operates normally on all inputs that

have a signal. On inputs that do not have a signal, the plasma panel displays a cycling single

color test pattern (see below) which is generated internally. This can be helpful to determine

if the panel is capable of displaying anything.

NOTE:

1st number indicates normal button operation

2nd number indicates function during MENU

Rear Label

7654321

- + OK

2. VOL

2. ADJ

1. SUB POWER

3. VOL

3. ADJ

4. PROGRAM

4.SELECT

5. PROGRAM

5.SELECT

6. INPUT SELECT

6. OK

7. MENU

126

BURN-IN MODE (ON)

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold the

buttons down until the initial OSD goes

away. OSD will then appear indicating that

BURN-IN MODE is engaged.

(OSD > Burn In On)

1 2

BURN-IN MODE (OFF)

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold the

buttons down until the initial OSD goes

away. OSD will then appear indicating that

BURN-IN MODE is disengaged.

(OSD > Burn In Off)

White Yellow Cyan Green Magenta Red Blue Black

CMP420V1 / CMP420V2 / 42EDT41 (PW1A)

DEMO MODE

When the DEMO feature is turned ON, both the remote and the plasma panel front panel

buttons (with the exception of the SUB POWER button) are non-operational. This can be

useful for the Sales / Dealers to prevent anyone from playing with any of the settings.

NOTE: This is the front panel shortcut to parameter #175 in the I2C ADJUSTMENT MODE.

NOTE:

1st number indicates normal button operation

2nd number indicates function during MENU

Rear Label

7654321

- + OK

2. VOL

2. ADJ

1. SUB POWER

3. VOL

3. ADJ

4. PROGRAM

4.SELECT

5. PROGRAM

5.SELECT

6. INPUT SELECT

6. OK

7. MENU

DEMO MODE (OFF)

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold

the buttons down until the initial OSD goes

away. DEMO MODE is now disengaged,

although you will not see any OSD confir-

mation.

1 3

DEMO MODE (ON)

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold the

buttons down until the initial OSD goes

away. DEMO MODE is now engaged, al-

though you will not see any OSD confirma-

tion.

136

SERVICE MODE ACCESS

DEMO MODE

CMP420V1 / CMP420V2 / 42EDT41 (PW1A)

I2C ADJUSTMENT MODE

When the set is in the I2C Adjustment mode, use the cursor buttons for selecting the

adjustment parameter, and for changing the parameter’s value. Use the OK button to

confirm. After adjustments are complete, press the MENU button to return the set to normal

operating condition.

NOTE:

1st number indicates normal button operation

2nd number indicates function during MENU

Rear Label

7654321

- + OK

2. VOL

2. ADJ

1. SUB POWER

3. VOL

3. ADJ

4. PROGRAM

4.SELECT

5. PROGRAM

5.SELECT

6. INPUT SELECT

6. OK

7. MENU

I2C Adjustment Mode

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold the

buttons down until the initial OSD goes

away. OSD will then appear indicating that

I2C ADJUSTMENT MODE is engaged.

146

MEMORY INITIALIZATION

Don’t indiscriminately perform this procedure as it can result in a loss of data if the old val-

ues were not recorded.

1. Engage I2C Adjustment mode.

2. Select parameter #744. Change the data value from “0” to “1”.

3. Activate MEMORY INITIALIZATION by holding down the OK button for at least

three seconds.

4. Select parameter #374. Change the data value from “1” to “0”.

5. Check that the set changes input to AV1, indicating that the preset values have been

loaded.

SERVICE MODE ACCESS

I2C ADJUSTMENT MODE

CMP420V1 / CMP420V2 / 42EDT41 (PW1A)

FACTORY RESET

Occasionally, it becomes necessary to perform a factory reset. This is different than the

Memory Initialization, only customer settings are affected by Factory Reset.

NOTE:

1st number indicates normal button operation

2nd number indicates function during MENU

Rear Label

7654321

- + OK

2. VOL

2. ADJ

1. SUB POWER

3. VOL

3. ADJ

4. PROGRAM

4.SELECT

5. PROGRAM

5.SELECT

6. INPUT SELECT

6. OK

7. MENU

Factory Reset

With unit in standby mode

(turned off), press and hold: >

After the unit comes on, continue to hold the

buttons down until the initial OSD goes

away. Factory Reset has now engaged,

although you will not see any OSD confir-

mation.

156

SERVICE MODE ACCESS

FACTORY RESET

Autres manuels pour CMP420V1

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Moniteur

Hitachi

Hitachi 32PD5000 Manuel utilisateur

Hitachi

Hitachi CML150XE Manuel utilisateur

Hitachi

Hitachi 42PD5000 Manuel utilisateur

Hitachi

Hitachi CML190SXWB - 19" LCD Monitor Manuel utilisateur

Hitachi

Hitachi UltraVision UT47V702 Manuel utilisateur

Hitachi

Hitachi CML175SXWB Manuel utilisateur

Hitachi

Hitachi COLOR PLASMA TELEVISION 42PD9800TA Manuel utilisateur

Hitachi

Hitachi CM615ET Manuel utilisateur

Hitachi

Hitachi 55HDM71 - 55" Plasma Panel Manuel utilisateur

Hitachi

Hitachi CML152XW2 Manuel utilisateur

Hitachi

Hitachi COLOR PLASMA TELEVISION 42PD9800TA Manuel utilisateur

Hitachi

Hitachi CML154XW Manuel utilisateur

Hitachi

Hitachi CM827ET Manuel utilisateur

Hitachi

Hitachi CML151XW Manuel utilisateur

Hitachi

Hitachi CPX2102MS Manuel utilisateur

Hitachi

Hitachi CMP5000WXJ Manuel utilisateur

Hitachi

Hitachi CPX14QE Manuel utilisateur

Hitachi

Hitachi CM823FET Manuel utilisateur

Hitachi

Hitachi 55HDM71 - 55" Plasma Panel Manuel utilisateur

Hitachi

Hitachi 32PD5000 Manuel utilisateur

Hitachi

Hitachi CML200UXWB Manuel utilisateur

Hitachi

Hitachi CMP205SXE Manuel utilisateur

Hitachi

Hitachi CMP205SXE Manuel utilisateur

Hitachi

Hitachi CMP420V1A Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation