HIK VISION DS-K1101M Manuel utilisateur

DS-K1100 Series Card Reader

Installation Manual

UD.6L0206A1003A01

Thank you for purchasing our product. If there is any question or

request, please do not hesitate to contact the dealer.

This manual is applicable to the following models:

Series

Models

Description

DS-K1101

Series

DS-K1101M

MIFARE card reader (without keypad)

DS-K1101MK

MIFARE card reader (with a keypad)

DS-K1101C

CPU card reader (without keypad)

DS-K1101CK

CPU card reader (with a keypad)

DS-K1102

Series

DS-K1102M

MIFARE card reader (without keypad)

DS-K1102MK

MIFARE card reader (with a keypad)

DS-K1102C

CPU card reader (without keypad)

DS-K1102CK

CPU card reader (with a keypad)

DS-K1103

Series

DS-K1103M

MIFARE card reader (without keypad)

DS-K1103MK

MIFARE card reader (with a keypad)

DS-K1103C

CPU card reader (without keypad)

DS-K1103CK

CPU card reader (with a keypad)

This manual is a kind of guide only for reference and may contain

several technically inaccurate points or printing errors, and the

content is subject to change without notice. The updates will be

added into the new version of this manual. We will readily

improve or update the products or procedures described in the

manual.

There may be differences between real object. The real product

should be considered as final.

Chapter 1 Preventive and Cautionary

Tips

To guarantee the card reader works properly, please read and

obey the notes below.

If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.

If the distance is longer than 100m, you are advised to power

the card reader by external 12V (range: -%10 ~ +%10) DC

power supply, which is nonswitched and linear.

To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to

connect them.

If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

If you need to install several card readers, the distance

among them must over 30cm.

To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and

card reader terminal.

Chapter 2 Introduction

DS-K1100 series card reader is a kind of high-performance

product, with a 32 bit high-speed processor. It communicates with

access controller via either RS-485 protocol or Wiegand protocol.

And a build-in tamper-proof module helps to protect card reader

from malicious damage. As to the physical appearance, the

PC+ABS material makes water proof and dust proof possible in

poor environment.

2.1 Front View

The front view of DS-K1101 series card reader is shown below:

Figure 2-1 DS-K1101MK/DS-K1101CK

Figure 2-2 DS-K1101M/DS-K1101C

The front view of DS-K1102 series card reader is shown below:

Figure 2-3 DS-K1102MK/DS-K1102CK

Figure 2-4 DS-K1102M/DS-K1102C

The front view of DS-K1103 series card reader is shown below:

Figure 2-5 DS-K1103MK/DS-K1103CK

Figure 2-6 DS-K1103M/DS-K1103C

2.2 Rear View

The rear view of card reader is shown below:

Figure 2-7 Rear View of DS-K1101 Series

Figure 2-8 Rear View of DS-K1102 Series

Figure 2-9 Rear View of DS-K1103 Series

Table 2-1 Description of Rear View

No.

Name

Cable Interface of RS-485, Power, LED Control, etc.

Buzzer

Tamper-proof Module

DIP Switch

PSAM Card Slot (available for CPU card reader)

2.3 Side View

The side view of card reader is shown below:

Figure 2-10 Side View of DS-K1101 Series

Figure 2-11 Side View of DS-K1102 Series

Figure 2-12 Side View of DS-K1103 Series

Chapter 3 Installation

3.1 Installing PSAM Card

PSAM card slot is only available for CPU card reader.

Insert the PSAM card into the slot according to the direction

shown below.

Figure 3-1 PSAM Card Slot

3.2 Introduction for DIP Switch

The DIP switch module is shown below. The No. of DIP switch

from left to right is 1 ~ 8.

Figure 3-2 DIP Switch Module

Table 3-1 Description of DIP Switch

Icon

Description

Represent 1 in binary mode

Represent 0 in binary mode

For example, binary value of the following status is: 0000 1100.

Figure 3-3 DIP Switch Module

Table 3-2 Description of DIP Switch

No.

Description

DIP Switch Status

1 ~ 4

Address of RS-485

1: 1

0: 0

Read card No. or file in card.

(Only available for CPU card

reader.)

1: read card No;

0: read file in card.

Wiegand protocol or RS-485

protocol.

1: Wiegand protocol;

0: RS-485 protocol.

Wiegand Protocol

(available when No. 6 is 1)

1: Wiegand protocol

of 26-bit;

0: Wiegand protocol

of 34-bit.

Matched Resistance

(available for RS-485 protocol)

1: Enable;

0: Disable.

3.3 Definition of Cable

The description of 10 cables is shown below.

Table 3-3 Description of Cable

Color

Description

Yellow

RS-485+

Brown

Blue LED Control (available for Wiegand Protocol)

Blue

RS-485-

Purple

Beep Control (available for Wiegand Protocol)

Gray

Case Sensor (available for Wiegand Protocol)

Green

Wiegand W0 (available for Wiegand Protocol)

White

Wiegand W1 (available for Wiegand Protocol)

Black

GND

Autres manuels pour DS-K1101M

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HIK VISION Lecteur de cartes

HIK VISION

HIK VISION DS-K1106M Manuel utilisateur

HIK VISION

HIK VISION DS-K1100M Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1100 Series Guide de démarrage rapide

HIK VISION

HIK VISION DS-k1106 Manuel utilisateur

HIK VISION

HIK VISION DS-K1201A Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1802 Series Manuel utilisateur

HIK VISION

HIK VISION LTK1802 Series Manuel utilisateur

HIK VISION

HIK VISION D8E Series Manuel utilisateur

HIK VISION

HIK VISION K1201AMF Manuel utilisateur

HIK VISION

HIK VISION DS-K1107A Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1108AM Manuel utilisateur

HIK VISION

HIK VISION DS-K1201AEF Manuel utilisateur

HIK VISION

HIK VISION DS-K1200 Series Mode d’emploi

HIK VISION

HIK VISION K1108AMK Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1101M Manuel utilisateur

HIK VISION

HIK VISION DS-K1201MF Manuel utilisateur

HIK VISION

HIK VISION DS-K1108AD Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1108 Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1100 Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1109 Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1107MK Manuel utilisateur

HIK VISION

HIK VISION DS-TRI4 Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1107 Series Manuel utilisateur

HIK VISION

HIK VISION DS-K1107 Series Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur