Heltun HE-HT01 Manuel utilisateur

HEATING THERMOSTAT HE-HT01

USER MANUAL V1.0

Table of Contents
 



 !
"!
#$!
%#&%'#$()*+
#,&$#$(-%.*+
/0& .#$+
,%&,. .#$1
2-%&2#$(- *1
#-3&#%#$(4*1
%$56(5%*1
 /(/,*1
7.#1
"58
%.9:
%.99
%.9;
 <.9
 9
"$,. %9
)$29
=&>369
-$$.=&>69
/.'=&>69
 9
9
-?$9
-9!
=&>"2;9!
7.?.=&>"(@ *9!
 $'9+
> (;&0*98
;

Overview

This is the user manual for HELTUN HE-HT01 Advanced Programmable Thermostat for Heating S stems.

The HE-HT01 can be flush mounted over standard electrical junction boxes. It is designed to maintain a constant room

temperature b providing sensors for both ambient and radiant floor heating s stems. It is recommended for control of

electric heating s stems (radiator, convection, electric fireplace), boilers, or electric underfloor heating. Heating

elements are directl controlled b a single-pole switch. The maximum load for the HE-HT01 thermostat is 16 Amps

(4000W @ 250VAC) which must be connected through a circuit breaker.

The HE-HT01 has an LCD screen, six sensitive capacitive touch control buttons, and two temperature sensors (for

ambient air temperature and an external NTC floor sensor). It is also equipped with built-in sensors for humidit ,

illumination, and energ consumption.

The HE-HT01 integrates a Z-Wave 700 platform module allowing it to be used with Z-Wave home automation s stems.

The HE-HT01 supports Z-Wave ‘S0’ and ‘S2’ securit protocols, SmartStart technolog , and can be connected

(“associated”) to ten other Z-Wave devices, such as rela s, switchers, etc.

You can select one of six operation modes either manuall , or b using a Z-Wave controller/gatewa . As a safet

measure, the HE-HT01 protects radiant floor s stems from overheating b automaticall switching off if the

temperature reaches 40°C.

The displa has a user-friendl interface, showing: ambient air temperature, floor temperature, user set point, humidit

level, current operating mode, time, da of the week, and status of the Z-Wave network and rela . Displa brightness

adjusts to ambient light conditions automaticall making it alwa s eas to read.

Technical Specifica ions

Front frame (on wall) dimensions: 89mm (H) х 89mm (W) х 9mm (D)

Rear electronics package dimensions: 53mm (H) х 53mm (W) х 28mm (D)

Materials: Tempered glass displa /bod , Flame retardant plastic

5 frame colors: White, Gloss Black, Matte Black, Silver, Chrome

6 glass colors: White, Black, Yellow, Green, Red, Blue

LCD: 73mm x 42mm (3.3 inch), black with white segments

6 capacitive-touch buttons

Operating temperature: 0°С to +50°С

Power suppl : 85-265VAC 50Hz/60Hz, 24-48VDC

Power consumption: 1W

Maximum resistive load: 16А, 4000W @ 250VAC

Rela switching with zero-cross technolog

Rela life time: 100.000 switches

Internal ambient light sensor

Internal temperature sensor

oMeasurement range: –30°C to +80°C

oAccurac : ±0.5°C

Internal humidit sensor

oMeasurement range: 0% to 80%RH

oAccurac : ±3.0%RH

External floor temperature sensor

oNTC 10kΩ

oMeasurement range: -30°C to +80°C

oAccurac : ±0.5°C

Energ consumption meter

IP class: IP21

Z-Wave Plus V2 SDK: V7.11

Z-Wave module: ZGM130S

Requires mounting to flush electrical junction box:

round or square t pe – min. depth 40mm



Func ions & Fea ures

Options for Inclusion/Exclusion to/from Z-Wave network

oNon-Secure

oS0 Secure

oS2 Unauthorized, S2 Authorized with Ke

Association control with 10 devices from network

6 operational modes with individual temperature set points:

oCOM – Comfort/Heating Mode

oECO – Energ saving Mode

oVAC – Vacation/Awa Mode

oDRY – Floor Dr Mode

oTIME – Schedule Mode

oMANUAL – Manual Control Mode

4 time schedules for 7 da s of the week:

oMorning

oDa

oEvening

oNight

Temperature sensor selection:

oFloor temperature onl

oAir temperature onl

oFloor + Air temperature

oPower regulator (Automatic ON/OFF timer)

Can be used with different NTC-sensors (range: 1kΩ to 100kΩ)

Periodic measurements from:

oInternal temperature sensor

oExternal floor temperature sensor

oInternal humidit sensor

oInternal ambient light sensor

oEnerg consumption meter

Calibration of Internal Room Air Temperature Sensor

Calibration of External NTC Temperature Sensor

Temperature set intervals: 4.0°C to 37.0°C

Temperature limiter: 40.0°C

Zero-cross rela switching

Temperature h steresis selection range: 0.2°C to 10.0°C

Temperature format: Celsius (°C) or Fahrenheit (°F)

Time mode format: 24 or 12 hours (AM/PM)

LCD brightness:

oAutomatic adjustment (depending on ambient light)

oManual adjustment (15 levels).

LCD standb mode (different brightness for active and inactive states)

LCD backlight blinking function (for eas identification among other Z-Wave devices)

Child lock mode (touch buttons lockout mode)

Real-time and cumulative energ usage to 0.1kW accurac

Factor reset function

SmartStart technolog for quick addition to Z-Wave networks

Encr pted OTA (Over The Air) firmware update feature



Ins alla ion

HELTUN recommends the HE-HT01 thermostat be installed b a licensed electrician in a

manner that conforms to local regulations and building codes. Provide these instructions to the

licensed electrician who is installing the HE-HT01.

WARNING: Elec rical power mus be swi ched off during ins alla ion.

1. Placement of the HE-HT01 is of utmost importance for proper operation and must be awa

from sunlight and sources of direct heat. We recommend installing the HE-HT01

approximatel 1.5 meters above the floor.

2. Remove the displa unit and backplate of the HE-HT01 from the packaging.

3. FIRST ENSURE THE POWER IS OFF at the main circuit breaker, and then test the wires

with a probe or multimeter to verif . Insert the power and heater wires to the correct HE-HT01

terminals b inserting a small Phillips-head screwdriver in the slot beneath each terminal to

open. Follow the connection diagram and instructions below:

• Power wires: connect Line & Neutral wires to L & N terminals labeled “IN”

• Hea er wires: connect Line & Neutral wires to L & N terminals labeled with “heating

element” graphic

Connection diagram 1 Connection diagram 2

4. If using the HE-HT01 for radiant floor heating, connect the NTC temperature

sensor wire to the terminals labeled “NTC.” A 10 kΩ NTC sensor is included

inside the HE-HT01 packaging, but an NTC sensor can be used.

No e: If an NTC sensor other than 10 kΩ is used, ou must change the

sensor Parameter value in the settings menu (Parameter 01 - FSr) – see

“Settings Menu” section below.

5. If ou will be using an external device to select modes for the HE-HT01

(such as a securit s stem), connect wires from the external device’s dr

contacts to the two HE-HT01 terminals labeled “EXT.”

6. Making sure the HE-HT01 backplate is oriented on the wall with the word

“TOP” pointed upwards, secure the backplate onto the electrical junction box

using the four provided screws (do not overtighten). Once the backplate is

secured onto the wall, assemble the HE-HT01 displa unit onto the

backplate b first carefull aligning the two top snap connectors, and then

gentl pushing the entire displa unit until it ‘snaps’ into position all the wa

around.

7. Next, switch On the main power at the circuit breaker (see photo above).

The HE-HT01 will start up showing the original default factor settings.

8. Remove the clear protective film from the displa unit b pulling on the top

right-hand tab.



Disassembly

1. To disassemble, ENSURE POWER IS SWITCHED OFF at the main circuit breaker AND THE LCD SCREEN IS

BLANK.

2. To remove the HE-HT01 displa unit grasp firml at the bottom and pull backwards while tilting outwards until all

tabs disconnect.

3. Remove screws from backplate and disconnect the wires b inserting a small Phillips-head screwdriver into the slot

beneath each wire to release.

Touch Panel Opera ion

The touch panel has six capacitive-touch buttons which require minimal pressure to operate.

Symbol: Name:

Plus

Minus

Time

Settings

Manual Heating

Mode

Function:

Increase Set Point Temperature

Decrease Set Point Temperature

Change Schedule

Open Parameters Menu

Manuall Switch Heating Element On or Off

Change the Operational Mode: (COM, TIME, DRY, ECO, VAC, MAN)

The Plus “+” button will increase Set Point temperature b 0.5°C (or 1°F) with each touch. The Minus “–“ button will

decrease Set Point temperature b the same 0.5°C (or 1°F). The Set Point temperature is displa ed in the bottom left

corner of the LCD displa under “SET TEMP.”

No e: The minimum Set Point is 4.0°C (or 39°F) and the maximum Set Point is 37.0°C (or 99°F).

The HE-HT01 has two working modes: HEATING (switched On) and IDLE (switched Off). In HEATING mode, the

heating element icon ( ) will appear near the right bottom corner of the displa (to the left of the connectivit icon).

The heating element icon will disappear when the HE-HT01 is in IDLE mode.

Opera ion Modes

The current Operating Mode is shown on the middle, right of the LCD displa under the label: “HEATING MODE.”

The HE-HT01 has 6 Operating Modes:

COM – Comfort Mode (heating)

TIME – Time Mode (schedule different Set Point per time and da )

DRY – Floor Dr ing Mode

ECO – Econom (power efficient / energ saving) Mode

VAC – Vacation Mode (i.e. ‘Awa ’ Mode)

MAN – Manual Mode

Change Modes b touching the MODE button (bottom right of displa unit) until the desired Mode is reached. Each

operating mode has individual temperature Set Points. The HE-HT01 will operate automaticall depending on the

current Set Point indicated under the SET TEMP label. To change the Set Point value, choose the desired mode and

press Plus “+” button to increase, or Minus “–” button to decrease. You ma alternativel control Set Points through

our Z-Wave gatewa software.

COM - Comfor Mode (Hea )

This mode is recommended for normal comfort. The factor default set point is 25.0°C (77°F).

TIME - Tempera ure Schedule Mode (Au o Changeover)

The Temperature Schedule (TIME) Mode can adjust home temperatures automaticall to align with our personal

habits, saving energ while ou are awa , and maintaining a comfortable temperature while ou are active at home.

The HE-HT01 can have different Schedules for Morning, Da time, Evening and Night.

For example, the “Morning” Schedule could be set to 25.0°C (77°F) starting at 7:00. The

“Da ” Schedule could then be set to 11.0°C (or 52°F) at 9:00 when ever one has gone to

work or school, and so on. Here are recommended Scheduled Set Points for heating

during the work week – ou ma wish to change these on weekends depending on our

famil ’s schedule (see example below):

Schedule

Mode

Set

Time

Set Point

Temperature

Morning 6:00 (6:00am) 24°C (75°F)

Day 9:00 (9:00am) 20°C (68°F)

Evening 18:00 (6:00pm) 23°C (73°F)

Nigh 23:00 (11:00pm) 18°C (64°F)

To set up the time and temperature for each Schedule press and hold the Clock “ ” button for three seconds. The

displa will change to the Time menu.

To set up the start time for each Schedule, choose the Schedule b pressing the Clock “ ” button then adjust the time

b pressing the Heating Element “ ” button to increase, or “MODE” button to decrease. Press the Clock “ ” button

again to advance to the next schedule and set the time for all four: Morning, Da , Evening & Night.

To choose the temperature Set Points for each Schedule, choose the da of the week b pressing the Gear “ ”

button, then choose the Schedule b pressing the Clock “ ” button and adjust the temperature Set Point up or down

b pressing the Plus “+” or Minus “–“ buttons. Do this action for each da of the week.

No e: All four Schedules (Morning, Da , Evening, & Night) are the same for all seven da s of the week.

No e: TIME mode will onl work properl if the correct current time and date have been set. The time can be

automaticall corrected from our Z-Wave gatewa if the Parameter 9 value is set to 1. Or it can be set manuall in

Parameters 11, 12, and 13 in the Settings Menu (see below).

No e: When in TIME mode, the temperature Set Point (under the label SET TEMP) will be automaticall changed

depending on the Schedule. At an time, the Set Point can be adjusted up or down manuall but it will be effective onl

until the next Schedule.

DRY - Fas Floor Drying Mode

This mode is recommended for use if a high floor temperature is required for a limited period of time. For example,

after washing the floor. B choosing DRY Mode, the HE-HT01 will increase the temperature to the selected Set Point

for the time specified in the “Dr Time” parameter (Parameter 7). A time range of 5 to 90 minutes can be set. As the

Dr Time passes, the HE-HT01 will automaticall change to the Mode set in Parameter 8.

To change the Dr Time Parameter, open the “Settings Menu” b pressing the Gears “ ” button for three seconds.

Use the and MODE buttons to scroll up and down through the menu to Parameter 07. Then use ke s “ +” and “–”

to increase or reduce the Dr Time setting (in minutes).

To choose the mode to revert to after Dr Time has elapsed (while still in the Settings Menu), press the or MODE

button to select Parameter 8, then use ke s “+” and “–” to choose the desired Mode as follows:

Mode:

COM

TIME

DRY

ECO

VAC

MAN

Value:

n/a

Notes:

This is the factor default for revert after DRY Mode (Parameter 8)

You cannot revert to DRY Mode.

If MAN Mode is chosen, the HE-HT01 will select IDLE state

No e: Factor defaults for Dr Time are: 30 minutes at 30.0°C (86°F).

ECO - Energy Saving Mode

This Mode can be used if lower temperature and energ consumption is desired. It can also be used at night or when

awa from all or part of the propert for a length of time. The factor default ECO Set Point is 20.0°C (68°F).

VAC - Vaca ion Mode (Away)

Use Vacation Mode when ou are planning to be awa from home for some period. The factor default temperature

Set Point is 15.0°C (59°F).

No e: The minimum set point for each mode is 4.0°C (39°F) and the maximum set point is 37.0°C (99°F).

MAN - Manual Con rol Mode (Off)

In this Mode the HE-HT01 schedules are disabled and the heating state is switched On & Off manuall b pressing the

Heating Element “ ” button.

No e: When in Manual Control Mode the SET TEMP will indicate “OFF.”

Child Lock (LOC)

The Child Lock feature allows ou to disable the HE-HT01 touch buttons temporaril . To activate the Child Lock Mode,

press and hold the Heating Element ( ) button for five seconds until the Lock Icon ( ) appears in the bottom center

of the displa . To deactivate the Child Lock, press the Heating Element ( ) button until the Lock Icon ( ) disappears.

Fac ory Rese (RES)

B pressing and holding the “MODE” ke for ten seconds, the HE-HT01 will enter Factor Reset Mode, displa ing

“REs” in the left bottom corner, “y” in top left corner and “n” in top right corner. Press the Plus (+) button to revert to

factor settings, or the Heating Element ( ) button to cancel. The factor reset will change all the Parameters to their

original factor default values and will also Exclude the device from an Z-Wave network.

No e: Please use this procedure onl when the network primar controller is missing or otherwise inoperable.

Se ings Menu

To enter the Settings Menu, press and hold the Gear “ ” button for three seconds. The top left corner will displa the

Parameter Number. The bottom left corner will displa the Parameter Name (abbreviated). And the top right corner will

displa the Parameter Value.

To scroll through the menu, press the Heating Element “ ” button to go up and the MODE ke  to go down.
To change the Parameter value, press the Plus “+” or Minus “–” buttons.
To leave the Settings Menu press and hold the   ke  for 3 seconds or just wait. If no action is detected for 10 seconds
the displa  will automaticall  revert to the main displa  mode.
Parame er Lis 
Group Number Name Descrip ion Defaul 
Value Value Range
Inputs
configuration
01 FSr Floor Sensor Resistance, kΩ 10 1…100
02 In 1 EXT input mode 0 0, 1, 2
03 In 2
Mode number for EXT input action:
1 = COM, 2 = TIME, 3 = DRY, 4 = ECO,
5 = VAC, 6 = MAN (On), 7 = MAN (Off)
6 1, 2, 3, 4, 5, 6, 7
04 SEn Source Sensor: 
1 = A, 2 = AF, 3 = F, 4 = FA, 5 = P, 6 = PA, 7 = PF 31, 2, 3, 4, 5, 6, 7
Time
configuration
05 POn Power Regulation ON time, min 30 10…240
06 POF Power Regulation OFF time, min 30 10…240
07 dr 1 Dr  Time, min 30 5…90
08 dr 2 Mode to revert to after completion of Dr  mode:
1 = COM, 2 = TIME, 4 = ECO, 5 = VAC, 6 = MAN (Off) 1 1, 2, 4, 5, 6
09 tCr Time correction b  controller 1 0, 1
10 tFo Time Format 0 0, 1
11 dA Da  of the Week 1 1, 2, 3, 4, 5, 6, 7
12 tIH Time: Hour 0 0…23
13 tIL Time: Minute 0 0…59
Temperature
configuration
14 AtL Air Temperature Minimum 21 / 69 4.0…36.0 °C
(39…96 °F)
15 AtH Air Temperature Maximum 27 / 80 5.0…37.0 °C
(41…98 °F)
16 FtL Floor Temperature Minimum 18 / 64 4.0…36.0 °C
(39…96 °F)
17 FtH Floor Temperature Maximum 32 / 89 5.0…37.0 °C
(41…98 °F)
18 dEg Temperature Units Selection: 0 = °C, 1 = °F 0 0 = °C, 1 = °F
19 AtC Air Temperature Calibration 0 (-9.5)…9.5 in °C
(-17)…17 in °F
20 FtC Floor Temperature Calibration 0 (-9.5)…9.5 in °C
(-17)…17 in °F
21 H S Temperature H steresis 0.5 / 0.9 0.2…10.0 in °C
0.3…18.0 in °F
Displa 
Brightness
22 Abc Displa  auto-brightness control 1 0, 1
23 Idb Displa  brightness manual control level 10 1…15
Touch
Sensitivit 24 tCH Touch button sensitivit :
5 = Highest sensitivit , 50 = Lowest sensitivit 15 5…50
Energ 
Consumption
25 AC AC voltage, Volt Read Onl 
26 Prr Energ  consumption meter value, kWH Read Onl 
27 POr Load Power, Watts Read Onl 
Versions 28 Hrd Hardware Version Read Onl 
29 APP Application Version Read Onl 
Z-Wave
30 bSA Mode selection upon Basic Set Action command:
1=COM, 2=TIME, 3=DRY, 4=ECO, 5=VAC, 6=MAN (On)
1 1, 2, 3, 4, 5, 6
31 nEt Inclusion / Exclusion Mode EcL InC, EcL
32 rEg Frequenc  Region EU
EU: Europe
US: USA
AU: Australia
HO: Hong Kong
IN: India
IL: Israel
RU: Russia
CN: China
JP: Japan
OR: Korea
8

Inpu Configura ion

Parame er 01 (“FSr”) – Floor Sensor Resis ance

If the external floor NTC temperature sensor is used it is necessar to select the correct resistance value in Ohms (Ω)

of the sensor. The selection range is 1 to 100 kiloOhms (kΩ). One 10kΩ NTC floor temperature sensor is included in

the HE-HT01 package with a 3-meter connection wire. The factor default value is 10kΩ.

No e: If the floor sensor is disconnected or damaged “—” will be shown on the LCD displa under the FLOOR TEMP

label.

Parame er 02 (“In 1”) – S1 Inpu Mode

The HE-HT01 can be connected to the dr output contacts of an external device (i.e. securit s stem) to control the

Thermostat operating modes depending on the state of the external device through.

Two different connection diagrams are possible.

No e: In case of using “S1 connection diagram 2”, it is MANDATORY to connect S1 terminal to the same wire

connected to terminal L on the device (labeled as “IN”) through dr contacts of an external device (like wall switch).

S1 connection diagram 1 S1 connection diagram 2

If Parameter value = 0 no action will be taken (the input state is ignored b the Thermostat logic).

If Parameter value = 1 the Thermostat will be switched to the operating mode selected in Parameter 3 if the output was

short-circuited. The Heating Thermostat will go back to previous mode as soon as the input is open.

I f Parameter value = 2 the HE-HT01 will be switched to the operating mode selected in Parameter 3 if the output was

short-circuited, but it will not undertake an action if the input is open again.

No e: The Mode switch is blocked when the Source Sensor (Parameter 4) is: P (value = 5), PA (value = 6) or PF

(value = 7). Factor default value is 0.

Parame er 03 (“In 2”) – Opera ing Mode For S1 Inpu Ac ion

This Parameter allows selection of which Operating Mode the HE-HT01 should revert to if the external input is short-

circuited. 1 = COM, 2 = TIME, 3 = DRY, 4 = ECO, 5 = VAC, 6 = MAN mode with IDLE (Off) state, 7 = MAN mode with

HEATING (On) state. Factor default value is 6.

Parame er 04 (“SEn”) – Source Sensor

The HE-HT01 has seven Regulation Modes based on different sensors values. Use the Plus “+” and Minus “–” buttons

to choose follow modes:

1) A – Air sensor

2) AF – Air sensor + Floor sensor

3) F – Floor sensor

4) FA – Floor sensor + Air sensor

5) P – Power regulator

6) PA – Power regulator + Air sensor

7) PF – Power regulator + Floor sensor

Autres manuels pour HE-HT01

Table des matières

Autres manuels Heltun Thermostat

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FC1 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL1 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL2 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur