Heltun HE-FT01 Manuel utilisateur

HE-FT01 USER MANUAL 1

FAN COIL THERMOSTAT

HE-FT01 USER MANUAL

for Hardware v.20 & Firmware v.2.2

HE-FT01 USER MANUAL 2

TABLE OF CONTENTS

OVERVIEW..................................................................................................................................................3

TECHNICAL SPECIFICATIONS..................................................................................................................4

FUNCTIONS & FEATURES.........................................................................................................................4

INSTALLATION............................................................................................................................................5

DISASSEMBLY............................................................................................................................................7

TOUCH PANEL OPERATION......................................................................................................................7

CLIMATE CONTROL MODES.....................................................................................................................8

Heating & Cooling....................................................................................................................................8

Heating ....................................................................................................................................................9

Cooling ....................................................................................................................................................9

Ventilation................................................................................................................................................9

FAN SPEED MODES...................................................................................................................................9

OPERATING MODES................................................................................................................................10

COM - Comfort Mode ............................................................................................................................10

TIME - Temperature Schedule Mode.....................................................................................................11

ECO - Energy Saving Mode...................................................................................................................12

OFF - Operating modes disabled...........................................................................................................12

CHILD LOCK (LOC)...................................................................................................................................12

FACTORY RESET (RES) ..........................................................................................................................13

Z-WAVE NETWORK..................................................................................................................................13

Adding to Z-Wave network ....................................................................................................................13

Removing from Z-Wave network ...........................................................................................................13

Security..................................................................................................................................................14

SmartStart..............................................................................................................................................15

Firmware OTA Update...........................................................................................................................15

Z-Wave Plus V2 Specifications..............................................................................................................15

Associations...........................................................................................................................................17

SETTINGS MENU......................................................................................................................................18

SETTINGS (available through menu and Z-Wave network).......................................................................19

Z-Wave..................................................................................................................................................20

Hardware & Software Versions..............................................................................................................21

Power and Energy Consumption...........................................................................................................21

Display Brightness.................................................................................................................................22

Touch Sensitivity....................................................................................................................................22

Outputs Configurations..........................................................................................................................22

Loads Power..........................................................................................................................................23

Temperature Configurations..................................................................................................................24

Time Configurations...............................................................................................................................24

SETTINGS (available through Z-Wave network only)................................................................................25

Time Mode Schedule.............................................................................................................................25

Sensors Report Interval.........................................................................................................................25

Association Commands Action..............................................................................................................27

PARAMETERS LIST & FACTORY DEFAULTS.........................................................................................27

LIMITED WARRANTY ...............................................................................................................................31

HE-FT01 USER MANUAL 3

OVERVIEW

This is the user manual for the HELTUN HE-FT01 Advanced Programmable Thermostat for

Fan Coil Heating/Cooling Systems. The HE-FT01 is elegantly designed and „Impossibly

Smart‟ providing wireless over-the-Internet control of your home‟s fan coil heating/cooling

system. The HE-FT01 is „Impossibly Thin‟ on the wall yet packed with features to help you

save energy while providing the ultimate comfort and convenience.

Perfectly controls air conditioning systems

The HE-FT01 is designed to maintain constant room temperatures by using internal air

temperature sensor. It controls 2-pipe or 4-pipe air conditioning/heating systems such as:

split/multi-split systems, chillers and fan coil unit systems, central air conditioning systems,

multi-zone VRF/VRV air conditioning systems, etc. The fan speed is controlled by three relay

outputs. Two more relay outputs control cooling and heating valves. The HE-FT01 has two

independent inputs for relay channels which allow it to control fans and valves with different

power sources or to use relay outputs as dry contacts. Each relay can carry a load of up to 5

Amps.

Multiple built-in sensors

The HE-FT01 has an LCD screen, six high sensitivity capacitive touch buttons, and internal

temperature sensor with compensating software for precise temperature monitoring and

control. It also has built-in humidity and illumination sensors. You can instantly access

information from all sensors on the user-friendly display.

Monitor all important information without even a touch

The at-a-glance display shows: ambient air temperature, user set point, humidity level,

current operating mode, climate mode, fan speed, time, day of the week, and status of the Z-

Wave™ network. Display brightness adjusts to ambient light conditions automatically making

it easy to read.

Highly configurable

You can select one of four operation modes (COM, TIME, ECO, OFF) with individual set

points either manually or by using a Z-Wave controller/gateway. The HE-FT01 operates in

four Climate Modes: Heating & Cooling, Heating only, Cooling only, and Ventilation and has

six fan speed control modes: Low, Medium, High, Auto Medium, Auto High, & Off.

Know how much energy you use

The HE-FT01 built-in Power Consumption System monitors how much energy you used

during any particular day, week, or month. Just specify the consumption of the load in watts

for each relay channel and the thermostat logic will calculate total consumption relative to

the time since the output was in the „ON‟ state.

Based on the latest Z-Wave platform

The HE-FT01 integrates a Z-Wave Plus™ v2 700 platform module allowing it to be used with

Z-Wave home automation systems. The HE-FT01 supports Z-Wave „S0‟ and „S2‟ security

protocols, SmartStart technology, and can be connected (“associated”) to other Z-Wave

devices, such as relays, switchers, etc.

HE-FT01 USER MANUAL 4

TECHNICAL SPECIFICATIONS

Front frame (on wall) dimensions:

89mm (H) х 89mm (W) х 9mm (D)

Rear electronics package dimensions:

53mm (H) х 53mm (W) х 28mm (D)

Materials: Tempered glass

display/body, Flame retardant plastic

4 frame colors: White, Matte Black,

Silver, Chrome

6 glass colors: White, Black, Yellow,

Green, Red, Blue

LCD: 72mm x 42mm (3.3 inch), black

with white segments

6 capacitive-touch buttons

Operating temperature: 0°С to +50°С

Power supply: 85-265VAC 50Hz/60Hz,

24-48VDC

Power consumption: 1W

5 relays with resistive load up to 5A

each

2 relays for cooling and heating

valves

3 relays for fan speed

2 independent relay inputs (dry contact)

HELTUN Advanced Zero-Cross relay

switching technology

Relays lifetime: 100.000 switches

Internal ambient light sensor

Internal temperature sensor

Measurement range: –30°C to

+80°C

Accuracy: ±0.5°C

Internal humidity sensor

Measurement range: 0% to 80%RH

Accuracy: ±3.0%RH

Software energy consumption logic

IP class: IP21

Z-Wave Plus V2 SDK: V7.11

Z-Wave module: ZGM130S

Requires mounting to flush electrical

junction box: round or square type –

min. depth 40mm

FUNCTIONS & FEATURES

Options for Inclusion/Exclusion to/from

Z-Wave network

Non-Secure

S0 Secure

S2 Unauthorized, S2 Authorized

with Key

Association control of Z-Wave devices

in network

4 operational modes with individual

temperature set points:

COM –Comfort Mode

ECO –Energy saving Mode

TIME –Schedule Mode

OFF –Idle

Four climate modes:

Heating & Cooling,

Heating only,

Cooling only,

Ventilation only

Six Fan Speed control modes:

Low speed

Medium speed

High speed

Auto Medium speed

Auto High speed

Off

4 Time Schedules for 7 days of the

week:

Morning

Day

Evening

Night

Periodic measurements from:

Internal temperature sensor

Internal humidity sensor

Internal ambient light sensor

Energy consumption logic

Calibration of Internal Room Air

Temperature Sensor

Temperature set intervals: 1.0°C to

37.0°C

Temperature hysteresis selection

range: 0.2°C to 10.0°C

Relays output NO / NC mode.

HELTUN Advanced Zero-Cross relay

switching technology

Time format: 24 or 12 hours (AM/PM)

HE-FT01 USER MANUAL 5

LCD brightness:

Automatic adjustment (depending

on ambient light)

Manual adjustment (10 levels).

LCD standby mode (different

brightness for active and inactive

states)

LCD backlight blinking function (for

easy identification among other Z-

Wave devices)

Child lock mode (touch buttons lockout

mode)

Power consumption software logic

Factory reset function

SmartStart technology for quick

addition to Z-Wave networks

Encrypted OTA (Over The Air)

firmware update feature

INSTALLATION

HELTUN recommends the HE-FT01 thermostat be installed by a licensed electrician or

HVAC installer in a manner that conforms to local regulations and building codes. Provide

these instructions to the licensed electrician who is installing the HE-FT01.

≡Note: It is not recommended to install the device in rooms with high humidity such as

bathroom or sauna

WARNING: ELECTRICAL POWER MUST BE SWITCHED OFF DURING INSTALLATION.

1. Placement of the HE-FT01 is of utmost importance for proper operation and must be

away from sunlight and sources of direct heat. We recommend installing the HE-FT01

approximately 1.5 meters above the floor.

2. Remove the display unit and backplate of the HE-FT01 from the packaging.

3. FIRST ENSURE THE POWER IS OFF at the main circuit breaker, and then test the

wires with a probe or multimeter to verify. Insert the power wires to the HE-FT01

“POWER” terminal by inserting a small Phillips-head screwdriver in the slot beneath

each terminal to open. Follow the connection diagrams and instructions below:

Connection Diagram 1

Connection Diagram 2

HE-FT01 USER MANUAL 6

Connection Diagram 3

Connection Diagram 4

Power wires: connect Line & Neutral wires to L & N terminals labeled “POWER”

Fan Speed: connect the required power source for Fan (Relays 1, 2 and 3 outputs)

to terminal IN-1-3.

Heating/Cooling valves: connect the required power source for Heating/Cooling

valves

(Relays 4 and 5 outputs) to terminal IN-4-5.

Loads: Connect the loads to relays output terminals:

OUT-1 for the Fan low speed

OUT-2 for the Fan medium speed

OUT-3 for the Fan high speed

OUT-4 for the heating valve

OUT-5 for the cooling valve

≡Note: HELTUN recommends installing cord terminals (electric wire ferrule) on the

ends of wires before connecting them to the HE-FT01 (various colors terminals are

included in the packaging).

4. Make sure the HE-FT01 backplate is oriented on the wall with the word “TOP” pointed

upwards. Then secure the backplate onto the electrical junction box using the four

screws provided (do not overtighten). Once the backplate is secured onto the wall,

assemble the HE-FT01 display unit onto the backplate by first carefully aligning the two

top snap connectors, and then gently pushing the entire display unit until it „snaps‟ into

position all the way around.

5. Next, switch ON the main power at the circuit breaker. The HE-FT01 will start up

showing the original default factory settings.

6. Remove the clear protective film from the display unit and frame by pulling on the top

right-hand orange color tabs.

≡Note: Zero-Cross technology is unavailable if the device operates using DC voltage

(24-48VDC).

HE-FT01 USER MANUAL 7

123

DISASSEMBLY

1. To disassemble, ENSURE POWER IS SWITCHED OFF at the main circuit breaker

AND THE LCD SCREEN IS BLANK.

2. To remove the HE-FT01 display unit grasp firmly at the bottom and pull backwards

while tilting outwards until all tabs disconnect.

3. Remove screws from backplate and disconnect the wires by inserting a small Phillips-

head screwdriver into the slot beneath each wire to release.

TOUCH PANEL OPERATION

The touch panel has six capacitive-touch buttons which require minimal pressure to operate.

The Plus “+” button will increase Set Point temperature by 0.5°C with each touch. The Minus

“–” button will decrease Set Point temperature by the same 0.5°C. The Set Point

temperature is displayed in the bottom left corner of the LCD display under “SET TEMP.”

Set temperature

increase

Set temperature

decrease

Settings menu/

Climate mode selection

Fan speed selection

Operating

mode selection

Temperature

schedule

HE-FT01 USER MANUAL 8

≡Note: The minimum Set Point is 1.0°C and the maximum Set Point is 37.0°C.

CLIMATE CONTROL MODES

The HE-FT01 has four climate states:

HEATING (OUT-4 is On, OUT-5 is Off, one of OUT-1/2/3 is ON),

COOLING (OUT-5 is On and OUT-4 is Off one of OUT-1/2/3 is ON),

VENTILATION (both OUT-4 and OUT-5 are Off, one of OUT-1/2/3 is ON),

IDLE (all outputs are Off).

In the HEATING and COOLING states, in addition to OUT-4 & OUT-5, one output from

OUT-1, OUT-2, & OUT-3 will be switched on depending on selected speed. The icons

HEATING, COOLING, & VENTILATION are displayed in the center, bottom of the display.

Those icons will disappear when the HE-FT01 is in IDLE mode.

≡Note: In HEATING and COOLING operation states the Fan operation can be

disabled in Parameters 10 and 11.

The current Climate Control mode is shown on the middle-right position of the LCD under

“OPERATING MODE.”

The HE-FT01 can operate in 4 climate modes:

Icon

Device Climate mode

Device Operating Mode

Mode in Z-Wave

gateway

Heating & Cooling

“COM” or “TIME”

“Auto Changeover” or

“Auto”

Heating

“COM” or “TIME” or

“ECO”

“Heat” or “Energy Heat”

Cooling

“COM” or “TIME” or

“ECO”

“Cool” or “Energy Cool”

Ventilation

OFF

“Fan”

Change the climate mode by touching the Climate button and selecting as shown above.

Heating & Cooling

In this mode, the HE-FT01 switches between heating and cooling states automatically. The

primary purpose of automatic climate control is to manage the temperature of the area to

provide maximum comfort. This means the thermostat will heat the room when the room

temperature is lower than the temperature Set Point, and it will cool the room when room

temperature is higher than the Set Point.

≡Note: This Mode is available only for “COM” and “TIME” Operating Modes.

≡Note: According to Z-Wave protocol standards, your Z-Wave gateway will show this

mode as “Auto Changeover” if you have selected “COM” Operating Mode, or as

“Auto” if you have selected “TIME” Operating Mode.

HE-FT01 USER MANUAL 9

Heating

This mode is used when only heating is needed as in winter. In this mode, when the room

temperature is lower than the Set Point, the thermostat will switch ON the heater (OUT-4 will

be ON, OUT-5 will be OFF). When room temperature goes higher than the Set Point, it will

switch to IDLE mode (all five outputs will be OFF).

≡Note: According to Z-Wave protocol standards, your Z-Wave gateway will show this

mode as: 1) “Heat” if you have selected “COM” Operating Mode, or as 2) “Energy

Heat” if you have selected “ECO” Operating Mode, or as 3) “Auto” if you have

selected “TIME” Operating Mode.

Cooling

This mode is used when only cooling is needed as in summer. In this mode, when the room

temperature is higher than the Set Point, the thermostat will switch ON the air conditioner

(OUT-5 will be ON, OUT-4 will be OFF). When the temperatures goes lower than the Set

Point, the thermostat will goes to IDLE mode (all five outputs will be OFF).

≡Note: According to Z-Wave protocol standards, your Z-Wave gateway will show this

mode as: 1) “Cool” if you have selected the “COM” Operating Mode, or as 2)

“Energy Cool” if you have selected “ECO” Operating Mode, or as 3) “Auto” if you

have selected “TIME” Operating Mode.

Ventilation

In Ventilation mode the thermostat circulates air around the room without heating or cooling

(heating and cooling valves are closed: OUT-4 and OUT-5 will be always OFF).

≡Note: when in Ventilation mode, all Operating Modes (COM, TIME, ECO) are

disabled and "OFF" will be displayed under "SET TEMP" on the LCD.

≡Note: According to Z-Wave protocol standards your Z-Wave gateway will show this

mode as “Fan.”

FAN SPEED MODES

The HE-FT01 has six fan speeds:

Low speed (OUT-1 is ON)

Medium speed (OUT-2 is ON)

High speed (OUT-3 is ON)

Auto Medium speed (OUT-1 or OUT-2 is ON)

Auto High speed (OUT-1 or OUT-2 or OUT-3 is ON)

OFF (OUT-1, OUT-2 and OUT-3 are OFF)

HE-FT01 USER MANUAL 10

In Low, Medium, and High speeds, the thermostat always runs the selected speed (OUT-1

will be ON in case if Low speed is selected, OUT-2 will be ON for Medium speed, OUT-3 will

be ON for High speed).

At Auto Medium speed, the thermostat will run at Low speed (OUT-1 is ON) if the Set Point

and room temperatures difference is less than 1.0°C, and Medium speed (OUT-2 is ON) if

the Set Point and ambient temperatures difference is higher 1.0C.

At Auto High speed mode, the thermostat will run at Low speed (OUT-1 is ON) if the Set

Point and room temperatures difference is less than 1.0°C. It will run Medium speed (OUT-2

is ON) if the Set Point and room temperatures difference is higher than 1.0°C but less then

2.0°C. And it will run on High speed (OUT-3 is ON) if the Set Point and room temperatures

difference is higher than 2.0°C. If the Fan Speed is OFF, the thermostat will go to IDLE

mode (all outputs will be OFF).

≡Note: depending on speed level, only one output from the group OUT-1, OUT-2, or

OUT-3 will be ON.

≡Note: in Auto Medium and Auto High speed the selected speed icon will blink, and

the current speed icon will be constantly ON.

OPERATING MODES

The HE-FT01 thermostat has Four Operating Modes as follows:

COM –Comfort Mode

TIME –Time Mode (enables different scheduled temperature Set Points per time

and day)

ECO –Economy Mode (energy saving)

OFF –Operating modes disabled

You may change Modes by touching the “MODE” button (bottom right of display unit) until

the desired Mode is reached.

Each Operating Mode (except TIME mode) has individual temperature Set Points for each

Climate Mode (Heating & Cooling Modes). The HE-FT01 will operate automatically

depending on the current Set Point indicated under the “SET TEMP” label on the LCD. To

change the Set Point value, choose the desired Operating Mode (COM, TIME or ECO),

choose the Climate Mode (“Heating”, “Cooling” or “Heating & Cooling”) and press the Plus

“+” button to increase, or Minus “–” button to decrease the corresponding Set Point value.

You may alternatively control Set Points for each Operating and Climate Mode through your

Z-Wave gateway software.

COM - Comfort Mode

This mode is recommended for maximum comfort. Under this Operating Mode there are

three different Climate control modes: “Heating & Cooling”, “Heating” and “Cooling”. And

each Climate Mode has its own individual Set Point. Choose the desired climate mode and

adjust the temperature Set Point for each mode separately.

≡Note: In your Z-Wave gateway you will see three Set Points corresponding to

different climate modes: “Auto Changeover” in Z-Wave corresponds to “Heating

& Cooling” climate mode in the HE-FT01, “Heat” corresponds to “Heating”

climate mode, and “Cool” corresponds to “Cooling” climate mode.

Autres manuels pour HE-FT01

Table des matières

Autres manuels Heltun Thermostat

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FC1 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL1 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL2 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur