Heltun HE-HT01 Manuel utilisateur

HE-HT01 USER MANUAL 1

HEATING THERMOSTAT

HE-HT01 USER MANUAL

for Hardware v.12 & Firmware v.2.2

HE-HT01 USER MANUAL 2

TABLE OF CONTENTS

OVERVIEW...................................................................................................................................................3

TECHNICAL SPECIFICATIONS...................................................................................................................4

FUNCTIONS & FEATURES..........................................................................................................................4

INSTALLATION.............................................................................................................................................5

DISASSEMBLY.............................................................................................................................................7

TOUCH PANEL OPERATION.......................................................................................................................8

OPERATION MODES...................................................................................................................................8

COM - Comfort Mode (Heat......................................................................................................................9

TIME - Temperature Schedule Mode (Auto Changeover) ........................................................................9

DRY - Fast Floor Drying Mode (Dry Air) .................................................................................................10

ECO - Energy Saving Mode (Energy Save Heat)...................................................................................11

VAC - Vacation Mode (Away).................................................................................................................11

MAN - Manual Control Mode (Off)..........................................................................................................11

CHILD LOCK (LOC)....................................................................................................................................11

FACTORY RESET (RES) ...........................................................................................................................11

Z-WAVE NETWORK...................................................................................................................................12

Adding to Z-Wave network .....................................................................................................................12

Removing from Z-Wave network ............................................................................................................12

Security...................................................................................................................................................13

SmartStart...............................................................................................................................................13

Firmware OTA Update............................................................................................................................14

Z-Wave Plus V2 Specifications...............................................................................................................14

Associations............................................................................................................................................16

SETTINGS MENU.......................................................................................................................................16

SETTINGS (available through menu and Z-Wave network)........................................................................17

Z-Wave...................................................................................................................................................19

Hardware & Software Versions...............................................................................................................20

Power and Energy Consumption............................................................................................................20

Display Brightness..................................................................................................................................21

Touch Sensitivity.....................................................................................................................................21

Input & Output Configurations.................................................................................................................21

Temperature Configurations...................................................................................................................22

Time Configurations................................................................................................................................25

SETTINGS (available through Z-Wave network only).................................................................................25

Time Mode Schedule..............................................................................................................................26

Sensors Report Interval..........................................................................................................................26

Association Commands Action...............................................................................................................27

PARAMETERS LIST & FACTORY DEFAULTS..........................................................................................28

LIMITED WARRANTY ................................................................................................................................32

HE-HT01 USER MANUAL 3

OVERVIEW

This is the user manual for HELTUN HE-HT01 Advanced Programmable Thermostat for

Heating Systems. The HE-HT01 is elegantly designed and ‗Impossibly Smart‘ providing

wireless over-the-Internet control of your home‘s heating system. The HE-HT01 is

‗Impossibly Thin‘ on the wall yet packed with features to help you save energy while

providing the ultimate comfort and convenience.

Controls electric heating systems

The HE-HT01 is designed to maintain constant room and floor temperatures by providing

sensors for both ambient and radiant floor heating systems. It controls electric heating

systems like radiators, convection or electric fireplaces, plus boilers, and electric underfloor

heating. Heating elements are directly controlled via a 16 Amp switch.

Multiple built-in sensors

The HE-HT01 has an LCD screen, six high sensitivity capacitive touch buttons, and two

temperature sensors for monitoring: ambient air temperatures, and floor temperatures using

the included external NTC sensor. It is also equipped with built-in sensors for: humidity,

illumination, and energy consumption. You can instantly access information from all

sensors on the user-friendly display.

Monitor all important information without even atouch

The at-a-glance display shows: ambient air temperature, floor temperature, user set point,

humidity level, current operating mode, time, day of the week, and status of the Z-Wave™

network & relay. Display brightness adjusts to ambient light conditions automatically making

it always easy to read.

Highly configurable with automatic safety

You can select one of six operation modes with individual set points either manually, or by

using a Z-Wave controller/gateway. As a safety measure, the HE-HT01 protects radiant

floor systems from overheating by automatically switching off if the floor temperature

reaches 40°C.

Know how much energy you use

The HE-HT01 built-in Power Consumption System precisely monitors how much energy

you used during any particular day, week, or month.

Based on the latest Z-Wave platform

The HE-HT01 integrates a Z-Wave Plus™ v2 700 platform module allowing it to be used

with Z-Wave home automation systems. The HE-HT01 supports Z-Wave ‗S0‘ and ‗S2‘

security protocols, SmartStart technology, and can be connected (―associated‖) to other Z-

Wave devices, such as relays, switches, etc.

HE-HT01 USER MANUAL 4

TECHNICAL SPECIFICATIONS

Front frame (on wall) dimensions:

89mm (H) х 89mm (W) х 9mm (D)

Rear electronics package

dimensions: 53mm (H) х 53mm (W) х

28mm (D)

Materials: Tempered glass

display/body, Flame retardant plastic

4 frame colors: White, Matte

Black, Silver, Chrome

6 glass colors: White, Black,

Yellow, Green, Red, Blue

LCD: 72mm x 42mm (3.3 inch),

black with white segments

6 capacitive-touch buttons

Operating temperature: 0°С to +50°С

Power supply: 85-265VAC

50Hz/60Hz, 24-48VDC

Power consumption: 1W

Maximum resistive load: 16А, 4000W

@ 250VAC

HELTUN Advanced Zero-Cross

relay switching technology

Relay life time: 100.000 switches

Internal ambient light sensor

Internal temperature sensor

Measurement range: –30°C to

+80°C

Accuracy: ±0.5°C

Internal humidity sensor

Measurement range: 0% to

80%RH

Accuracy: ±3.0%RH

External floor temperature sensor

NTC 10kΩ

Measurement range: -30°C to

+80°C

Accuracy: ±0.5°C

Real time energy consumption

meter

IP class: IP21

Z-Wave Plus V2 SDK: V7.11

Z-Wave module: ZGM130S

Requires mounting to flush

electrical junction box: round or

square type –min. depth 40mm

FUNCTIONS & FEATURES

Options for Inclusion/Exclusion to/from

Z-Wave network

Non-Secure

S0 Secure

S2 Unauthorized, S2 Authorized

with Key

Association control of Z-Wave

devices in network

6 operational modes with

individual temperature set points:

COM –Comfort/Heating Mode

ECO –Energy saving Mode

VAC –Vacation/Away Mode

DRY –Floor Dry Mode

TIME –Schedule Mode

MAN –Manual Control Mode

4 time schedules for 7 days of the

week:

Morning

Day

Evening

Night

Temperature sensor selection:

Floor temperature only

Air temperature only

Floor + Air temperature

Power regulator (Automatic

ON/OFF timer)

Can be used with different NTC-

sensors (range: 1kΩ to 100kΩ)

Periodic measurements from:

Internal temperature sensor

External floor temperature sensor

Internal humidity sensor

Internal ambient light sensor

Energy consumption meter

Calibration of Internal Room

Air Temperature Sensor

Calibration of External NTC

Temperature Sensor

Temperature set intervals: 1.0°C

to 37.0°C

HE-HT01 USER MANUAL 5

Temperature limiter: 40.0°C

Temperature hysteresis selection

range: 0.2°C to 10.0°C

Relay output NO / NC mode

HELTUN Advanced Zero-Cross

Relay switching technology

Time format: 24 or 12 hours

(AM/PM) LCD brightness:

LCD brightness

Automatic adjustment

(depending on ambient light)

Manual adjustment (10 levels).

LCD standby mode (different

brightness for active and inactive

states)

LCD backlight blinking function (for

easy identification among other Z-Wave

devices)

Child lock mode (touch buttons

lockout mode)

Real-time and cumulative energy

usage to 0.1kW accuracy

Factory reset function

SmartStart technology for quick

addition to Z-Wave networks

Encrypted OTA (Over The Air)

firmware update feature

INSTALLATION

HELTUN recommends the HE-HT01 thermostat be installed by a licensed electrician in a

manner that conforms to local regulations and building codes. Provide these instructions to

the licensed electrician who is installing the HE-HT01.

≡Note: It is not recommended to install the device in rooms with high humidity

such as bathroom or sauna.

WARNING: ELECTRICAL POWER MUST BE SWITCHED OFF DURING INSTALLATION.

1. Placement of the HE-HT01 is of utmost importance for proper operation and must

be away from sunlight and sources of direct heat. We recommend installing the HE-

HT01 approximately 1.5 meters above the floor.

2. Remove the display unit and backplate of the HE-HT01 from the packaging.

3. FIRST ENSURE THE POWER IS OFF at the main circuit breaker, and then test the

wires with a probe or multimeter to verify. Insert the power and heater wires to the

correct HE-HT01 terminals by inserting a small Phillips-head screwdriver in the slot

beneath each terminal to open. Follow the connection diagrams and instructionsbelow:

▪Power wires: connect Line & Neutral wires to L & N terminals labeled ―IN‖

▪Heater wires: connect Line & Neutral wires to L & N terminals labeled with ―heating

element‖ graphic

HE-HT01 USER MANUAL 6

Connection Diagram 1

Connection Diagram 3

Connection Diagram 2

Connection Diagram 4

≡Note: HELTUN recommends installing cord terminals (electric wire ferrule) on the

ends of wires before connecting them to the HE-HT01 (various colors terminals are

included in the packaging).

≡Note: If using the HE-HT01 for radiant floor heating, connect the NTC temperature

sensor wire to the terminals labeled ―NTC.‖ A 10 kΩ NTC sensor is included in the

HE-HT01 packaging, but also different NTC-sensors can be connected (range: 1kΩ

to 100kΩ).

≡Note: If an NTC sensor other than 10 kΩ is used, sensor Parameter value should

be changed in the settings menu (Parameter 10 –FSr) –see ―Settings Menu‖

section below.

4. If you will be using an external device to select modes for the HE-HT01 (such as a

security system), connect wires from the external device‘s dry contacts according to

connection diagrams 1 (or 2 or 3 or 4).

≡Note: There could be ―EXT‖ label instead of ―S1‖, ―Sx‖.

HE-HT01 USER MANUAL 7

5. Make sure the HE-HT01 backplate is oriented on the wall with the word ―TOP‖

pointed upwards, secure the backplate onto the electrical junction box using the four

provided screws (do not overtighten). Once the backplate is secured onto the wall,

assemble the HE-HT01 display unit onto the backplate by first carefully aligning the two

top snap connectors, and then gently pushing the entire display unit until it ‗snaps‘ into

position all the way around.

6. Next, switch On the main power at the circuit breaker (see photo above). The HE-HT01

will start up showing the original default factory settings.

7. Remove the clear protective film from the display unit and frame by pulling on the top

right-hand orange color tabs.

≡Note: Zero-Cross technology is unavailable if the device operates using DC

voltage (24-48VDC).

123

DISASSEMBLY

1. To disassemble, ENSURE POWER IS SWITCHED OFF at the main circuit breaker

AND THE LCD SCREEN IS BLANK.

2. To remove the HE-HT01 display unit grasp firmly at the bottom and pull backwards

while tilting outwards until all tabs are disconnected.

3. Remove screws from backplate and disconnect the wires by inserting a small Phillips-

head screwdriver into the slot beneath each wire and turning counter-clockwise to

release.

HE-HT01 USER MANUAL 8

TOUCH PANEL OPERATION

The touch panel has six capacitive-touch buttons which require minimal pressure to operate.

The Plus ―+‖button will increase Set Point temperature by 0.5°C with each touch. The

Minus ―–―button will decrease Set Point temperature by the same 0.5°C. The Set Point

temperature is displayed in the bottom left corner of the LCD display under ―SET TEMP.‖

≡Note: The minimum Set Point is 1.0°C and the maximum Set Point is 37.0°C.

The HE-HT01 has two working modes: HEATING (switched On) and IDLE (switched Off).

In HEATING mode, the heating element icon will appear near the right bottom corner of

the display (to the left of the connectivity icon). The heating element icon will disappear

when the HE-HT01 is in IDLE mode.

OPERATING MODES

The current Operating Mode is shown on the middle right of the LCD display under the

label: ―HEATING MODE.‖

The HE-HT01 has 6 Operating Modes:

COM –Comfort Mode (Heat)

TIME –Time Mode (Auto Changeover - schedule different Set Point per time and day)

DRY –Floor Drying Mode (Dry Air)

ECO –Power Efficient Mode (Energy Save Heat)

VAC –Vacation Mode (Away)

MAN –Manual Control Mode (Off)

Change Modes by touching the “MODE” button (bottom right of display unit) until the

desired Mode is reached. Each operating mode has individual temperature Set Points. The

HE-HT01 will operate automatically depending on the current Set Point indicated under the

“SET TEMP” label on the LCD. To change the Set Point value, choose the desired mode

and press Plus “+” button to increase, or Minus “–” button to decrease the corresponding

Operating

mode selection

Manual

ON / OFF

Set temperature

decrease

Set temperature

increase

Settings menu

Temperature

schedule

HE-HT01 USER MANUAL 9

Set Point value. You may alternatively control Set Points through your Z-Wave gateway

software.

COM - Comfort Mode (Heat)

This mode is recommended for maximum comfort. The factory default set point is 25.0°C.

≡Note: In your Z-Wave gateway this mode will be shown as“Heat”.

TIME - Temperature Schedule Mode (Auto Changeover)

The Temperature Schedule (TIME) Mode can adjust home temperatures automatically to

align with your personal habits, saving energy while you are away, and maintaining a

comfortable temperature while you are active at home.

The HE-HT01 can have different

Schedules for Morning, Daytime, Evening

and Night. For example, the ―Morning‖

Schedule could be set to 22.0°C

starting at 6:00. The ―Day‖

Schedule could then be set to 17.0°C at

9:00 when everyone has gone to work

or school, and so on. Here are

recommended Scheduled Set Points for

heating during the work week –you may

wish to change these on weekends

depending on your family‘s schedule

(see example below):

Schedule Mode

Set Time

Set Point Temperature

Morning

6:00 (6:00 AM)

22°C

Day

9:00 (9:00 AM)

17°C

Evening

18:00 (6:00 PM)

21°C

Nigh

23:00 (11:00 PM)

18°C

To set up the time and temperature for each Schedule press and hold the Clock button

for three seconds. The display will change to the Time menu.

To set up the start time for each Schedule, choose the Schedule by pressing the Clock

button then adjust the time by pressing the Heating Element button to increase, or

―MODE‖ button to decrease. Press the Clock button again to advance to the next

schedule and set the time for all four: Morning, Day, Evening & Night.

HE-HT01 USER MANUAL 10

To choose the temperature Set Points for each Schedule, choose the day of the week by

pressing the Gear button, then choose the Schedule by pressing the Clock button and

adjust the temperature Set Point up or down by pressing the Plus ―+‖ or Minus ―–― buttons.

Do this action for each day of the week.

≡Note: Time for all four Schedules (Morning, Day, Evening, & Night) are the same

for all seven days of the week.

≡Note: TIME mode will work properly only if the correct current time and date have

been set. The time can be automatically corrected from your Z-Wave

gateway if the Parameter 19 value is set to 1. Or it can be set manually in

Parameters 21 and 22 in the Settings Menu (see below).

≡Note: While in TIME mode, the temperature Set Point (under the label ―SET

TEMP‖on the LCD) will be automatically changed depending on the Schedule.

The Set Point can be adjusted up or down manually at any time, but it will be

effective only until the next Schedule.

≡Note: In your Z-Wave gateway this mode will be shown as ―Auto Changeover‖.

DRY - Fast Floor Drying Mode (Dry Air)

This mode is recommended for use if a high floor temperature is required for a limited

period of time. For example, after washing the floor. By choosing DRY Mode, the HE-HT01

will increase the temperature to the selected Set Point for the time specified in the ―Dry

Time‖ Parameter (Parameter 25). A time range of 5 to 90 minutes can be set. As the Dry

Time passes, the HE-HT01 will automatically change to the Mode set in Parameter 26.

To change the Dry Time Parameter, open the ―Settings Menu‖ by pressing the Gears

button for three seconds. Use the and ―MODE‖ buttons to scroll up and down through

the menu to Parameter 25. Then use buttons ―+‖ and ―–‖ to increase or reduce the Dry Time

setting (in minutes).

To choose the mode to revert to after Dry Time has elapsed (while still in the Settings

Menu), press the or ―MODE‖ button to select Parameter 26, then use buttons ―+‖ and ―–

‖ to choose the desired Mode as follows:

Mode:

Value:

Notes:

COM

This is the factory default for revert after DRY Mode (Parameter 26)

TIME

DRY

n/a

You cannot revert to DRY Mode.

ECO

VAC

MAN

If MAN Mode is chosen, the HE-HT01 will select IDLE state

Autres manuels pour HE-HT01

Table des matières

Autres manuels Heltun Thermostat

Heltun

Heltun HE-ZW-THERM-FC1 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL1 Manuel utilisateur

Heltun

Heltun HE-ZW-THERM-FL2 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-FT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Heltun

Heltun HE-HT01 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur