Harman JBL S4700 Manuel utilisateur

Instore "130"youcanfind and buy almostall necessary goodsforyourauto in

Kyiv and other cities,delivery by ground andpostal services.Ourexperienced

consultantswill provide youwithexhaustive informationand helpyoutochose

the very particular thing. We are waiting foryou atthe address

https://130.com.ua

PHONES

0 (800) 800 130

(050) 462 0 130

(063) 462 0 130

(067) 462 0 130

Internet storeof

autogoods

CARRECEIVERS —Receivers •Mediareceiversandstations•Nativereceivers •CD/DVD changers •FM-modulators/USBadapters•Flashmemory•Faciaplates and adapters •Antennas •Accessories |

CARAUDIO —Car audiospeakers •Amplifiers•Subwoofers •Processors•Crossovers •Headphones•Accessories|TRIPCOMPUTERS —Universalcomputers •Modelcomputers •Accessories|

GPSNAVIGATORS —PortableGPS•Built-in GPS•GPSmodules •GPStrackers •Antennas forGPSnavigators•Accessories|VIDEO —DVR •TVsetsand monitors•Car TVtuners•Cameras •Videomodules

•Transcoders •Car TVantennas•Accessories|SECURITYSYSTEMS —Car alarms •Bikealarms •Mechanicalblockers •Immobilizers •Sensors •Accessories |OPTICANDLIGHT —Xenon•Bixenon •Lamps

•LED •Stroboscopes •OpticandHeadlights •Washers •Light,rainsensors •Accessories |PARKTRONICS ANDMIRRORS —Rear parktronics•Frontparktronics •Combined parktronics •Rear-viewmirrors

•Accessories |HEATINGANDCOOLING —Seat heaters •Mirrorsheaters •Screen-wipers heaters •Engineheaters •Auto-refrigerators •Airconditioningunits •Accessories |TUNING —Vibro-isolation

•Noise-isolation •Tintfilms •Accessories |ACCESSORIES —Radar-detectors•Handsfree,Bluetooth•Windowlifters•Compressors •Beeps,loudspeakers •Measuring instruments •Cleaners •Carsits

•Miscellaneous|MOUNTING —Installationkits •Upholstery•Grilles•Tubes•Cableand wire •Tools•Miscellaneous|POWER —Batteries •Converters •Start-chargingequipment•Capacitors

•Accessories |MARINE AUDIOANDELECTRONICS —Marinereceivers•Marineaudiospeakers •Marinesubwoofers •Marineamplifiers•Accessories |CARCARE PRODUCTS —Additives •Washer fluid •

Care accessories •Car polish •Flavors •Adhesives andsealants |LIQUIDANDOIL —Motoroil•Transmissionoil •Brakefluid •Antifreeze•Technicallubricant

SKYPE

km-130

OWNER’S MANUAL

JBL®S4700

15-inch (380mm) 3-way ﬂoorstanding loudspeaker

Autogoods “130”

130.com.ua

INTRODUCTION

THANK YOU for purchasing the JBL®S4700 3-way floorstanding loudspeaker. For more than 60 years, JBL engineers

have been providing audio equipment for homes, concert halls, recording studios and movie theaters around the

world, and JBL products have become the hands-down choice of leading recording artists and sound engineers.

The S4700 is a new member of the family of JBL floorstanding loudspeakers designed for home use. To get the best

performance from your new loudspeakers, please read these instructions thoroughly.

PACKAGE CONTENTS

EACH JBL S4700 BOX CONTAINS:

• One (1) JBL S4700 floorstanding speaker

• Four (4) spike inserts to be installed on the speaker’s feet

• Four (4) metal coasters for use on tile, wood and linoleum floors

If you suspect that there has been shipping damage, report it immediately to your dealer. We recommend that you

keep the box and packing materials for future use.

UNPACKING THE SPEAKER

CAUTION: The S4700 weighs 54.5kg (120 lb). To avoid personal injury or damage to floors or the speaker,

we strongly recommend that at least two people unpack and move the speaker.

The speaker has stainless-steel feet that accept the supplied spiked inserts installed on the bottom of its cabinet. To

avoid damage to your floor, we strongly advise that you unpack the speaker on a well-protected surface, such as a

thick carpet or a thick piece of cardboard.

TO UNPACK THE SPEAKER:

1. Open the box flaps and, while standing on the box’s lower flap, gently rock the speaker and its packing back and

forth while pulling it out of the carton. In this way you can “walk” the speaker out of the carton. It helps to have a

second person hold the carton steady from the back side.

2. Once the speaker is out of the carton, remove the upper and middle pads. The speaker’s accessories are packed

on the top end of the upper pad, so be careful not to discard them.

3. Remove the cloth bag covering the speaker.

4. With another person’s help, carefully tilt the speaker on its side onto a thickly carpeted or well-padded surface and

remove the bottom pad.

5. Tilt the speaker back up on its feet.

4. 5.

2. 3.

Autogoods “130”

130.com.ua

www.jbl.com

English

www.jbl.com

INSTALLING THE SPIKED FOOT INSERTS

Before using the speaker, install the supplied spiked inserts into the speaker’s metal feet.

1. Turn the speaker upside down onto a thickly carpeted or well-padded surface.

2. Screw the spiked inserts into the feet.

IMPORTANT: To prevent damage (scratches, indentations, etc.) to wood or linoleum floors due to the weight of these

speakers, always use the included coasters. Be especially sure to use the coasters on tile surfaces to prevent cracking

the tile.

PLACEMENT

Because the stainless-steel spikes solidly couple the speaker to the floor, a flat, hard surface such as wood or linoleum

is preferable. However, the coupling system, along with the speakers’ weight, should result in excellent performance

on any surface, even carpeting.

IMPORTANT: To prevent damage (scratches, indentations, etc.) to wood or linoleum floors, always use the included

coasters. Be especially sure to use the coasters on tile surfaces to prevent cracking the tile.

To decide on a final location for your speakers, survey your room and think about placement, using the illustration

below as a guide.

>50cm

(20 in)

>50cm

(20 in)

1.5m – 2.5m

(5' – 8')

40° – 60°

Listening Position

For the best results, place the speakers about one and one-half to two and one-half meters (about five to eight feet)

apart. If you place the speakers farther apart, angle them toward the listening position.

The speakers will produce the most accurate stereo soundstage when the angle between the listener and the speakers

is between 40 and 60 degrees.

Position each speaker so that its tweeter is approximately at ear level.

Generally, bass output will increase as the speaker is moved closer to a wall or corner. For the best performance, we

recommend that you place the speakers at least 50cm (about 20 inches) away from the side walls.

NOTES ABOUT SPEAKER PLACEMENT:

• To prevent damage (scratches, indentations, etc.) to wood or linoleum floors due to the weight of these speakers,

always use the included coasters. Be especially sure to use the coasters on tile surfaces to prevent cracking the tile.

• Avoid placing the speakers near power ampliﬁers, heat registers or other objects that generate large amounts of heat.

• Do not place the speakers in very humid or dusty places.

• Do not place the speakers in direct sunlight or in places where they will be exposed to other strong light.

• The S4700 is not video-shielded and may distort or discolor the picture if placed close to some types of TVs. If

the speakers do distort or discolor your TV’s picture, move the speakers away from the TV until the distortion or

discoloration disappears.

Autogoods “130”

130.com.ua

CONNECTIONS

CAUTION: Make sure that all of the system’s electrical components are turned OFF (and preferably

unplugged from their AC outlets) before making any connections.

Speakers and amplifiers have corresponding positive and negative (“+” and “–”) connectors. The S4700 has two

sets of connectors; jumper bars connect the connectors to each other. The connectors are marked “+” and “–.”

Additionally, the “+” connectors have red rings, while the “–” connectors have black rings. See the illustration below.

Negative (–)

Connectors

Positive (+)

Connectors

We have designed the S4700 so that a positive voltage at the “+” (red) connector will cause the speaker transducers to

move outward (toward the room).

We recommend using a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding

is usually considered positive polarity (“+”).

To ensure proper polarity, connect the left- and right-channel “+” connectors on the back of the amplifier or receiver

to their respective “+” (red) connectors on the speakers. Connect the “–” (black) connectors in a similar way. See the

owner’s manual of your receiver or amplifier to confirm its connection procedures.

BASIC SINGLE-WIRE CONNECTION:

Connect the amplifier to each speaker as shown in the illustration below. You can use either set of connectors on

the speaker. NOTE: Do not remove the jumper bars from between the two sets of connectors when connecting the

speaker wires.

Receiver or Amplifier

(one channel shown)

Speaker

Connector Panel

IMPORTANT: Do not reverse polarities (i.e., “+” to “–” or “–” to “+”) when making connections. Doing so will cause

poor stereo imaging and diminished bass performance.

The S4700’s gold-plated speaker connectors can accept a variety of wire-connector types: bare wire, spade

connectors, pin connectors and banana connectors.

Autogoods “130”

130.com.ua

www.jbl.com

English

Using Bare Wire or Pin Connectors:

A. Unscrew Cap B. Insert Bare Wire or

Pin Connector through

Hole in Post

C. Tighten Cap

to Secure Wire

IMPORTANT: Make sure the “+” and “–” wires or pins do not touch each other or the other connector. Touching wires

can cause a short circuit that can damage your receiver or amplifier.

Using Spade Connectors:

A. Unscrew Cap C. Tighten Cap to Secure

Spade Connector

B. Insert Spade Connector

Blades around Post

IMPORTANT: Make sure the “+” and “–” spade connector blades do not touch each other or the other connector.

Touching blades can cause a short circuit that can damage your receiver or amplifier.

Using Banana Connectors:

A. Tighten Cap B. Insert Banana Connector

into Hole in Cap

BI-WIRE CONNECTION:

The S4700 connection assembly has two sets of input connectors that are connected by jumper bars. The upper set

of connectors is for high-frequency/ultrahigh-frequency drivers, and the lower set of connectors is for the woofer.

High-Frequency/

Ultrahigh-Frequency

Connectors

Low-Frequency

Connectors

Jumper

Bars

This arrangement allows you to bi-wire the speakers using a single stereo power amplifier or two stereo power

amplifiers. Bi-wiring can offer performance advantages and more flexibility in power-amplifier selection over a

conventional single-wire connection.

Autogoods “130”

130.com.ua

To bi-wire the S4700, first remove the connector jumper bars as shown in the illustration.

A. Unscrew

all four

caps

B. Remove

jumpers

If you’re bi-wiring with a single stereo power amplifier, connect the speakers according to the following illustration.

HF/UHF

Connection

Amplifier

Right

Ch.

Left

Ch.

HF/UHF

Connection

Low-Frequency

Connection

Low-Frequency

Connection

Right

Speaker

Left

Speaker

If you’re bi-wiring with two stereo power amplifiers, connect the speakers according to the following illustration.

HF/UHF

Connection

Amplifier 1

Amplifier 2

Right

Ch.

Right

Ch.

Left

Ch.

Left

Ch. HF/UHF

Connection

Low-Frequency

Connection

Low-Frequency

Connection

Right

Speaker

Left

Speaker

In either case, follow the instructions for the different connector types in Basic Single-Wire Connection, on page 4.

NOTE: For more information about various speaker-wire and connection options, contact your local JBL dealer.

Autogoods “130”

130.com.ua

English

www.jbl.com

CARING FOR YOUR SPEAKERS

Wipe the cabinet with a clean, dry cloth to remove dust. A damp cloth may dull the cabinet’s finish. Do not use volatile

liquids such as benzene, paint thinner or alcohol on the cabinet.

• Do not spray insecticide near the cabinet.

• To remove dust from the grille fabric, use a vacuum cleaner set to low suction.

• Do not wash the grille in water, as water may fade the grille’s color or make it uneven.

• Never apply suction or pressurized air to the high-frequency or ultrahigh-frequency horn openings.

• If the surface of the low-frequency driver cone becomes dusty, you can carefully sweep it clean with a soft, dry

calligraphy brush or paint brush. Do not use a damp cloth.

SPECIFICATIONS

JBL®S4700 FLOORSTANDING SPEAKER

Speaker type: 3-way floorstanding

Low-frequency transducer: 380mm (15") pure pulp cone with treated cloth edge and

Differential Drive®(U.S. patent no. 5,748,760 and other

patents pending) neodymium motor assembly

High-frequency transducer: 45mm (1-3/4") compression driver with an Aquaplas-treated

pure titanium diaphragm and neodymium motor assembly

on a SonoGlass®Bi-Radial®horn

Ultrahigh-frequency transducer: 19mm (3/4") compression driver with a pure titanium

diaphragm and neodymium motor assembly on a

SonoGlass®Bi-Radial®horn

Maximum recommended amplifier power: 300 watts RMS

Frequency response: 38Hz – 40kHz (–6dB)

Nominal impedance: 6 ohms

Sensitivity: 94dB (2.83V/1m)

Crossover frequencies: 800Hz, 12kHz

Enclosure type: 25mm (1")-thick MDF stock, ported

Connector type: Dual gold-plated five-way binding posts

Dimensions (H x W x D): 1075mm x 476mm x 372mm (42-3/8" x 18-3/4" x 14-5/8")

Weight: 54.5kg (120 lb)

Autogoods “130”

130.com.ua

HARMAN Consumer, Inc.

8500 Balboa Blvd., Northridge, CA 91329 USA

www.jbl.com

JBL, Differential Drive, SonoGlass and Bi-Radial are trademarks of HARMAN International Industries,

Incorporated, registered in the United States and/or other countries.

Features, specifications and appearance are subject to change without notice.

Part No. 950-0393-001

Autogoods “130”

130.com.ua

取扱説明書

JBL®S4700

15インチ（380mm）3ウェイ・フロアスタンディング・

ラウドスピーカー

Autogoods “130”

130.com.ua

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Harman Intervenants

Harman

Harman JBL Club 6.5" Manuel utilisateur

Harman

Harman JBL IRX ONE Manuel utilisateur

Harman

Harman JBL STADIUM 6 Manuel utilisateur

Harman

Harman JBL 4429 Manuel utilisateur

Harman

Harman Infinity KAPPA 53XF Manuel utilisateur

Harman

Harman JBL BAR 2.1 DEEP BASS Manuel utilisateur

Harman

Harman JBL Professional EON700 Series Manuel utilisateur

Harman

Harman JBL PROFESSIONAL VTX A8 Manuel utilisateur

Harman

Harman revel concerta 2 Manuel utilisateur

Harman

Harman Kardon ONYX STUDIO 6 Manuel utilisateur

Harman

Harman JBL IRX100 Series Manuel utilisateur

Harman

Harman JBL Performance Series Manuel utilisateur

Harman

Harman JBL Professional VTX Series Manuel utilisateur

Harman

Harman JBL FLIP ESSENTIAL 2 Manuel utilisateur

Harman

Harman JBL BOOMBOX 2 Manuel utilisateur

Harman

Harman JBL CRUISE Manuel utilisateur

Harman

Harman JBL EON618S Manuel utilisateur

Harman

Harman JBL PARTYBOX 1000 Manuel utilisateur

Harman

Harman JBL FLIP 5 Manuel utilisateur

Harman

Harman Harman/Kardon ONYX STUDIO 5 Manuel utilisateur

Harman

Harman JBL Soundpoint SP5 Manuel utilisateur

Harman

Harman JBL CHARGE5 Wi-Fi Manuel utilisateur

Harman

Harman EON 315 Manuel utilisateur

Harman

Harman PRX908 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur