Hach FilterTrak 660 Manuel utilisateur

52364-89

FilterTrak™ 660 Calibration Kit

General Information

The Calibration Kit, shown in Figure 1, is shipped with the calibration body (stand mounted),

a 1-liter bottle of 800 mNTU StablCal®Standard, and a funnel to reduce bubbles when

pouring the standard. The 800 mNTU StablCal Standard is assayed and the value is

reported on the label to the nearest 1 mNTU. The tolerance of the standard is ±50 mNTU.

Figure 1 Calibration Kit Components

Calibration Procedure

1. Remove the cover.

2. Rinse the calibration body with deionized water.

3. Drain all deionized water from the body and replace the drain plug.

4. Clean the FilterTrak 660 Nephelometer head assembly as described in the FilterTrak

660 Laser Nephelometer Instrument Manual (Cat. No. 52300-18).

5. Gently invert the StablCal Standard bottle 50 times to mix. Each inversion should last

1-3 seconds. Do not shake the standard.

6. Place the funnel into the end of the bubble trap, opposite the water intake. See Figure 2.

7. Slowly pour the standard into the funnel.

8. Install the FilterTrak 660 head assembly on the calibration body. See Figure 3.Allowthe

standard to sit undisturbed in the body for approximately 10–20 minutes before

proceeding with the calibration.

9. Calibrate using the instructions in the FilterTrak 660 Laser Nephelometer

Instrument Manual.

Calibration Body

Funnel

800 mNTU StablCal

1-liter Bottle

FilterTrak™ 660 Calibration Kit

HACH COMPANY

WORLD HEADQUARTERS

Telephone: (970) 669-3050

FAX: (970) 669-2932

FORTECHNICAL ASSISTANCE, PRICE INFORMATION AND ORDERING:

Call 800-227-4224

Contact the HACH office or distributor serving you.

www.hach.com [email protected]

In the U.S.A.–

Outside the U.S.A.–

On the Worldwide Web –; E-mail –

toll-free

10. When the calibration is complete, drain the calibration body. The standard cannot be

stored for future use.

11. Remove the head assembly and carefully rinse the head assembly and calibration body.

Immediately reinstall the head assembly back on the FilterTrak 660 body.

12. Store the calibration body with the cover securely in place.

Figure 2 Pouring the StablCal Standard

Figure 3 Calibration Body with FilterTrak 660 Head Assembly in Place

Place the funnel into the body.

Slowly pour the StableCal

Standard into the funnel

Drain

CONFIGURE

STATUS

POWER

REMOTE

Laser Turbidimeter

FilterTrak 660

™

FilterTrak 660

™

Table des matières

Autres manuels Hach Instrument de mesure

Hach

Hach TU5400 sc Manuel rapide

Hach

Hach CA610 Manuel utilisateur

Hach

Hach sensION MM340 Manuel utilisateur

Hach

Hach AMTAX sc Manuel utilisateur

Hach

Hach 1720E Manuel utilisateur

Hach

Hach CLF10sc Manuel utilisateur

Hach

Hach 9186 Manuel utilisateur

Hach

Hach POLYMETRON 8810 Manuel rapide

Hach

Hach Polymetron 9610sc Mode d'emploi

Hach

Hach 51 Series Manuel utilisateur

Hach

Hach LANGE LOC 100 Manuel utilisateur

Hach

Hach QbD1200 AutoSampler Manuel utilisateur

Hach

Hach Polymetron 9611sc Manuel utilisateur

Hach

Hach FH950 Manuel utilisateur

Hach

Hach QbD1200 AutoSampler Manuel utilisateur

Hach

Hach Polymetron 9586 Manuel utilisateur

Hach

Hach LDO101 Manuel utilisateur

Hach

Hach CLF10sc Manuel utilisateur

Hach

Hach Lange SensION+ MM 378 Manuel utilisateur

Hach

Hach sensION+ EC5 Manuel utilisateur

Hach

Hach BODTrak II Manuel utilisateur

Hach

Hach PAT700 DS Manuel rapide

Hach

Hach LXV321.99.00001 Manuel utilisateur

Hach

Hach BioTector B3500s Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur