H3C WA2612-AGN Manuel utilisateur

H3C WA2612-AGN

WLAN Access Point

Installation Manual

Table of Contents

1 Product Overview...................................................................................................... 1

Introduction............................................................................................................ 1

Hardware Specifications........................................................................................ 1

LEDs ............................................................................................................. 1

Interfaces ...................................................................................................... 2

2 Preparing for Installation ......................................................................................... 2

Unpacking and Inspection..................................................................................... 2

Temperature and Humidity Requirements............................................................ 2

Power Supply ........................................................................................................ 2

3 Installing the AP ........................................................................................................ 3

Determining the Installation Site............................................................................ 3

Installing the AP..................................................................................................... 3

Mounting the AP on a Wall........................................................................... 3

Mounting the AP on a ceiling................................................................................. 6

Mounting the AP to a T-Rail .................................................................................. 7

Power Supply by PoE............................................................................................ 9

4 Connecting to the AP ............................................................................................... 9

Approved Channels............................................................................................. 10

Finding the IP Address on Networks with a DHCP Server(FIT AP) ................... 10

Log into the AP.................................................................................................... 10

1 Product Overview

Introduction

The H3C WA2612-AGN is an 802.11n access point (AP) product developed by H3C.

The WA2612-AGN ships as a FIT AP (managed) and operate with wireless local area

network (WLAN) switches or access controllers to provide wireless access for WLAN

users. Hardware Specifications

The physical dimensions and weight of the WA2612-AGN:

Physical dimensions (diameter × thickness) Weight

Φ190 × 60 mm (Φ7.48 × 2.36 in.)

Note: Φmeans diameter 0.5 kg (1.10 lb.)

The basic configurations of the WA2612-AGN:

Protocols and chassis material Internal antenna Power

consumption

IEEE 802.11a/b/g/n,

single-RF, plastic mold design

2.4 GHz, gain: 6 dBi

5 GHz, gain: 6 dBi 5.9 W to 7 W

LEDs

When the AP is connected to power, LEDs indicate activities as follows:

LED Color State Description

POWER Green

Steady on The power supply is normal.

Off The power supply is poorly connected or is

working abnormally.

10/100M

(Ethernet

interface

LED)

Green

Steady on The Ethernet interface is in the link-up state.

Off The Ethernet interface is in the link-down state.

Blinking Data is being transmitted or received at 10/100

Mbps.

1000M

(Ethernet

interface

LED)

Green

Steady on The Ethernet interface is in the link-up state.

Off: The Ethernet interface is in the link-down state.

Blinking Data is being transmitted or received at 1000

Mbps.

2.4G

(Wireless

link LED)

Green

Off The wireless link is not initialized or the link is

faulty.

Blinking

slowly The wireless link is working normally

Blinking

rapidly Data is being transmitted or received.

(Wireless Green Off The wireless link is not initialized or the link is

faulty

LED Color State Description

link LED) Blinking

slowly The wireless link is working normally

Blinking

rapidly Data is being transmitted or received.

Interfaces

The WA2612-AGN provides a console interface and an Ethernet interface.

Note: The WA2612-AGN provides a reset button and a security slot.

Descriptions of the interfaces on the WA2612-AGN:

Interface

silkscreen

Standards and

protocols Description

CONSOLE RS/EIA-232 The console interface is used for device

configuration and management.

ETHERNET

IEEE802.3

IEEE802.3u

IEEE802.3af

The Ethernet interface can serve as an uplink

interface to access the Internet and as a PoE

interface at the same time.

Caution: When connecting a cable to an interface, pay attention to the interface

silkscreen to avoid connection mistakes.

2 Preparing for Installation

Unpacking and Inspection

Before unpacking the unit, make sure that the package is intact, without any sign of

damage. When unpacking the unit, avoid excessive force, otherwise, the unit inside

the package may get damaged.

After unpacking the unit, check that all items listed on the packing list are contained. If

any of the items are missing, contact your local dealer immediately.

Temperature and Humidity Requirements

The operating temperature and humidity requirements are as follows:

Specification Range

Operating temperature 0°C to 45°C (32°F to 113°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Relative humidity (non-condensing) 5% to 95%

Power Supply

The WA2612-AGN supports PoE power supply.

3 Installing the AP

Note:

1) Make sure that no metal particles (such as screws) fall into the Ethernet or

console interfaces during installation.

2) Before installing the WA2612-AGN to the wall-mounting bracket, connect the

network cable. The network cable can only be UTP cat-5.

3) Before connecting the console cable to the WA2612-AGN for debugging or

pressing the reset button, you need to remove the device from the

wall-mounting bracket.

Determining the Installation Site

Determine the installation site by observing the following principles:



Install the AP in an area away from obstacles that can cause interference.



Keep the AP far away from electronic devices (such as microwave ovens)

that may generate RF noise.



Ensure that the installation site will not cause any inconvenience or

nuisance.

Note:

1) Make sure the ceiling is strong enough and the structure is suitable in case of

ceiling mounting. Reinforce the ceiling if needed.

2) Us a Kensington lock if physical security is required to protect the AP from

being stolen.

Installing the AP

The WA2612-AGN support three installation methods:



Mounting the AP on a wall



Mounting the AP on a ceiling



Mounting the AP to a T-rail

Mounting the AP on a Wall

The following describes how to mount an WA2612-AGN on a wall:



Installing the wall-mounting bracket on the wall



Installing the AP on the wall-mounting bracket



Locking the AP onto the wall-mounting bracket (optional)

Installing the wall-mounting bracket on the wall

Step1 Place the wall-mounting bracket tightly against the wall where the AP is to be

mounted and mark the locations to drill holes for installing the screws. Then

use a drill with a bit of 6 mm (1/4 in) in diameter to drill holes in the wall. The

hole pattern must be identical with that in the wall-mounting bracket.

Highlight:

There are five mounting holes in total in the wall-mounting bracket of the

WA2612-AGN. Select the three round holes (with a diameter of 5 mm, or 0.20 in) for

the installation.

Figure1 Mounting hole pattern of, the WA2612-AGN wall-mounting bracket:

Step2 Insert the pointed end of wall anchors into the drilled holes and tap the flat end

of wall anchors with a rubber hammer until they are all flush with the wall

surface.

Step3 Align the holes in the wall-mounting bracket with the wall anchors and insert

screws through the mounting holes into the wall anchors, as shown in

Figure1.

Figure2 Install the wall-mounting bracket of the WA2612-AGN

(1) Drill hole (2) Wall anchor

(3) Wall-mounting bracket (4) Key-hole clip

(5) Screw

Step1 Adjust the position of the wall-mounting bracket and tighten the screws.

Note: Install the wall-mounting bracket with the arrow on the bracket pointing

upwards.

Installing the AP on the wall-mounting bracket

Step1 Align the AP with the key-hole clips on the wall-mounting bracket and hang

the AP on the bracket. See callout 1 in Figure3.

Step2 Press or rotate the AP to fix it. See callout 2 in Figure3. Fix the -shaped holes

on the AP’s rear panel to the key-hole clips on the wall-mounting bracket.

Figure3 Fix the WA2612-AGN onto the wall-mounting bracket

Note: Rotating the WA2612-AGN clockwise installs the device, while rotating it

counterclockwise uninstalls it.

Locking the AP onto the wall-mounting bracket (optional)

The WA2612-AGN has a security slot on the upper left side, which can be used to lock

the AP to a fixed object to prevent theft. Follow these steps to lock the AP to a fixed

object:

Step1 Fix the security cable to a nearby fixed object.

Step2 Insert the locking plate in the security slot to lock the AP.

Figure4 Lock the WA2612-AGN to a fixed object

(2)

(3)

(1)

Before installing the security lock: (1) Security slot

After installing the security lock : (2) Security lock

(3) Security cable

Note: The lock is user supplied.

Mounting the AP on a ceiling

Note:

1) To use this installation method, make sure that the thickness of the ceiling is

less than 18 mm (0.71 in), and the ceiling can bear the weight of at least 5 kg

(11.02 lb.).

2) You are not recommended to use this method to mount the AP to a location

made of low-intensity materials such as a plaster ceiling. If this installation

method is required in such an environment, put a high-intensity plate

beneath the nut to secure the installation.

Select the two mounting holes of the wall-mounting bracket as shown in Figure5 to

mount the AP on the ceiling (in mm). Follow these steps to mount the AP on the

ceiling:

Step1 Drill two holes in the ceiling corresponding to the two mounting holes in the

wall-mounting bracket.

Figure5 mounting holes on the wall-mounting bracket

(1) Mounting holes for mounting on a ceiling

Step2 Insert the bolts through the mounting holes of the wall-mounting bracket and

the drilled holes on the ceiling, and then tighten the nuts on the other side of

the ceiling to secure the wall-mounting bracket as shown in Figure6.

Figure6 Mount the wall-mounting bracket on the ceiling

(1) Bolt inside the ceiling (2) Washer

(3) Nut (4) Wall-mounting bracket

(5) Bolt cap (6) Key-hole clip

Step3 Mount the WA2612-AGN to the wall-mounting bracket. For details, refer to

Installing the AP on the wall-mounting bracket.

Mounting the AP to a T-Rail

Note: The width of the T-rail must be in the range of 14 mm (0.55 in) to 24 mm (0.94).

Follow these steps to mount the AP to a T-rail:

Step1 Loosen the two M3 × 6 screws on each clip holder until the screw heads are

lower than the upper edge of the nuts (do not remove the screws or they may

get lost).

Step2 Adjust the T-rail clips to make the T-rail holder wider than the T-rail, and then

lock the T-rail with the T-rail holder according to the arrow

Figure7 T-rail holder

(1) T-rail clip (2) M4×8 screw nut

(3) M3×6 screw nut (4) Clip holder

(5) M4×8 screw (6) M3×6 screw

(7) Mounting hook (8) T-rail holder

(9) Before installing to the T-rail, loosen the screw nuts until the screw heads

are lower than the upper edge of the nuts.

Step3 Tighten the M3 × 6 screws on the two clip holders until the screw heads touch

the T-rail, and then fix the screws.

Step4 Check that the T-rail holder is fixed to the T-rail.

Step5 Hook the mounting clip of the wall-mounting bracket to the mounting hook of

the T-rail holder, as shown Figure8.

Step6 Insert the two M4 × 8 screws through the two holes (with a diameter of 5 mm,

or 0.20 in) on the wall-mounting bracket according to the dashed line shown in

Figure8 and fix the screws to the T-rail holder.

Step7 Check that the wall-mounting bracket is fixed to the T-rail.

Step8 Install the WA2612-AGN to the wall-mounting bracket. For details, refer to

Installing the AP on the wall-mounting bracket.

Autres manuels pour WA2612-AGN

Table des matières

Autres manuels H3C Point d'accès sans fil

H3C

H3C UAP380 Manuel utilisateur

H3C

H3C WA2200 Series Manuel utilisateur

H3C

H3C AR 18-3XE/18-21X Series Manuel utilisateur

H3C

H3C WA5320 Manuel utilisateur

H3C

H3C WA2210-AG Manuel utilisateur

H3C

H3C WA4320H-ACN Manuel utilisateur

H3C

H3C WA2600 Series Manuel utilisateur

H3C

H3C WA Series Manuel d'installation

H3C

H3C WA2600 Series Manuel utilisateur

H3C

H3C WA Series Manuel d'installation

H3C

H3C WA6630X Manuel utilisateur

H3C

H3C WA5320X-E Manuel d'utilisation et d'entretien

H3C

H3C WA Series Manuel utilisateur

H3C

H3C WA2620X-AGNP Manuel utilisateur

H3C

H3C WA4330-ACN Manuel utilisateur

H3C

H3C WA6320H-HI Manuel utilisateur

H3C

H3C WA5330 Manuel utilisateur

H3C

H3C WA6330 Manuel utilisateur

H3C

H3C WA6320 Manuel utilisateur

H3C

H3C WA2110-AG Manuel utilisateur

H3C

H3C WA6636 Manuel utilisateur

H3C

H3C WA6638 Manuel utilisateur

H3C

H3C WA3610i-GN Manuel utilisateur

H3C

H3C WA2610E-AGN Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur