H3C MSR 5600 Manuel utilisateur

Contents

Preparing for installation················································································1

Safety recommendations ···································································································································1

Safety symbols···········································································································································1

General safety recommendations··············································································································1

Electricity safety·········································································································································1

Laser safety················································································································································2

Examining the installation site····························································································································2

Temperature and humidity·························································································································2

Cleanliness·················································································································································2

Cooling system···········································································································································3

ESD prevention··········································································································································3

EMI·····························································································································································4

Lightning protection····································································································································4

Rack-mounting···········································································································································5

Installation tools and accessories ······················································································································5

Pre-installation checklist·····································································································································6

Preparing for installation

The MSR5600 router series includes the models in Table 1.

Table 1 MSR5600 router series models

Model (on the front panel)

Product code

MSR5620 RT-MSR5620

MSR 56-60 RT-MSR5660

MSR 56-80 RT-MSR5680

Safety recommendations

Safety symbols

When reading this document, note the following symbols:

WARNING means an alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION means an alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or software.

General safety recommendations

•

Keep the chassis and installation tools away from walk areas.

•

Make sure the ground is dry and flat and anti-slip measures are in place.

•

Unplug all the external cables (including power cords) before moving the chassis.

Electricity safety

•

Locate the emergency power-off switch in the room before installation. Shut the power off at

once in case accident occurs. Disconnect the power cord of the router if necessary.

•

Make sure the router is correctly grounded.

•

Do not open or close the chassis cover when the router is powered on.

•

Correctly connect the interface cables of the router.

•

Use an uninterrupted power supply (UPS).

•

If there are two power inputs, disconnect the two power inputs to power off the router.

•

Do not work alone when the router has power.

•

Always make sure the power has been disconnected during the installation and replacement

procedures.

Laser safety

WARNING!

Do not stare into any

open apertures of operating transceiver modules or optical fiber connectors.

The laser light emitted from these apertures might hurt your eyes.

CAUTION:

•

Before you remove the optical fiber connector from a fiber port, execute the shutdown

command

in interface view to shut down the port.

•

Insert a dust cap into any unused optical fiber connector and a dust plug into any unused fiber

port or transceiver module port to protect them from contamination and ESD damage.

Examining the installation site

The routers can only be used indoors. To make sure the router operates correctly and to prolong its

service lifetime, the installation site must meet the following requirements.

Temperature and humidity

Maintain temperature and humidity in the equipment room as described in Table 2.

•

Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical

property change of materials, and metal corrosion.

•

Lasting low relative humidity can cause washer contraction and ESD and bring problems

including loose captive screws and circuit failure.

•

High temperature can accelerate the aging of insulation materials and significantly lower the

reliability and lifespan of the router.

Table 2 Temperature and humidity requirements

Operating temperature

Operating humidity

0°C to 45°C (32°F to 113°F) 5% RH to 95% RH, noncondensing

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure. To ensure correct operation, the

equipment room must meet the dust concentration requirements listed in Table 3.

Table 3 Dust concentration limit in the equipment room

Substance

Concentration limit (particles/m

)

Dust particles ≤ 3 x 104

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥ 5 µm

The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion

and premature aging of components, as shown in Table 4.

Table 4 Harmful gas limits in the equipment room

Gas

Max. (mg/m

)

SO20.2

H2S 0.006

NH30.05

Cl20.01

NO20.04

Cooling system

The router uses left to rear airflow for heat dissipation.

Figure 1 Airflow through the MSR 5600 chassis

To ensure good ventilation, the following requirements must be met:

•

Leave a minimum clearance of 10 cm (3.94 in) for the air inlet and outlet vents.

•

The installation site has a good cooling system.

ESD prevention

CAUTION:

Check the resistance of the

ESD wrist strap for safety. The resistance reading should be in the range

of 1 to 10 megohm (Mohm) between human body and the ground.

To prevent electrostatic discharge (ESD), follow these guidelines:

•

Make sure the router and the floor are reliably grounded.

•

Take dust-proof measures for the equipment room.

•

Maintain the humidity and temperature at acceptable levels.

•

Always wear an ESD wrist strap and ESD cloth when touching a circuit board or transceiver

module.

The router does not supply an ESD wrist wrap. Prepare an ESD wrist wrap yourself.

•

Place the removed memory module, CF card, or interface module on an antistatic workbench,

with the face upward, or put it into an antistatic bag.

•

Touch only the edges, instead of electronic components when you observe or move a removed

memory module, CF card, or interface module.

To attach an ESD wrist strap:

1. Wear the wrist strap on your wrist.

2. Lock the wrist strap tight around your wrist to keep good contact with the skin.

3. Insert the ESD plug into the ESD socket.

4. Connect the alligator clip to the rack.

EMI

All electromagnetic interference (EMI) sources, from outside or inside of the router and application

system, adversely affect the router in the following ways:

•

A conduction pattern of capacitance coupling.

•

Inductance coupling.

•

Electromagnetic wave radiation.

•

Common impedance (including the grounding system) coupling.

To prevent EMI, perform the following tasks:

•

If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)

to filter interference from the power grid.

•

Keep the router far away from radio transmitting stations, radar stations, and high-frequency

devices to make sure the EMI levels do not exceed the compliant range.

•

Use electromagnetic shielding, for example, shielded interface cables, when necessary.

•

To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning

strikes, only route interface cables indoors. If you must route interface cables outdoors, install

network port lightning protectors.

Lightning protection

The router has its own lightning protection system. To better protect the router from lightning, do as

follows:

•

Make sure the grounding cable of the chassis is reliably grounded.

•

Make sure the grounding terminal of the AC power receptacle is reliably grounded.

•

Install a lightning arrester at the input end of the power supply to enhance the lightning

protection capability of the power supply.

•

Install a special lightning arrester at the input end of outdoor signal lines (for example, E1/T1

line) to which interface modules of the router are connected to enhance the lightning protection

capability.

Rack-mounting

Before mounting the router in a standard 19-inch rack, adhere to the following requirements:

•

The rack is equipped with a good ventilation system.

•

The rack is sturdy enough to support the router and its accessories.

•

For heat dissipation and device maintenance, make sure the front and rear of the rack are at

least 0.8 m (2.62 ft) away from walls or other devices, and the headroom in the equipment room

is no less than 3 m (9.84 ft).

Installation tools and accessories

Figure 2 Installation tools

Figure 3 Installation accessories

Multimeter

Flathead screwdriver Phillips screwdriver Needle-nose pliers Wire-stripping pliers

ESD wrist strap Diagonal pliers Heat gun Cable tester Marker

Cage nut

(user-supplied)

Grounding cable

Removable cable tie

(user-supplied)

M6 rack screw

(user-supplied)

Air filter (optional)

M3 countersunk-head

screw (optional)

M4 mounting bracket

screw

MSR5620 shoulder

screw

MSR5620 front

mounting brackets MSR 56-60 front

mounting brackets MSR 56-80 front

mounting brackets MSR5620 rear mounting

brackets

Pre-installation checklist

Table 5 Pre-installation checklist

Item

Requirements

Result

Installation

site

Ventilation

•There is a minimum clearance of 10 cm (3.94 in)

around the inlet and outlet vents for heat dissipation of

the router chassis.

•A good ventilation system is available at the installation

site.

Operating

temperature 0°C to 45°C (32°F to 113°F).

Operating

humidity 5% RH to 95% RH, noncondensing.

Cleanliness •Dust concentration ≤ 3 × 104particles/m3.

•No visible dust on desk within three days.

ESD prevention

•The equipment and floor are reliably grounded.

•The equipment room is dust-proof.

•The humidity and temperature are at acceptable levels.

•An ESD wrist strap is available.

EMI prevention

•Effective measures are taken for filtering interference

from the power grid.

•The protection ground of the router is away from the

grounding facility of power equipment or lightning

protection grounding facility.

•The router is far away from radio transmitting stations,

radar stations, and high-frequency devices.

•Electromagnetic shielding, for example, shielded

interface cables, is used as required.

Lightning

protection

•The device is reliably grounded.

•The AC power source is reliably grounded.

•(Optional.) Network port lightning protectors are

available.

•(Optional.) Asurge protected power strip is available.

Electricity safety

•A UPS is available.

•The power-off switch in the equipment room is

identified and accessible so that the power can be

immediately shut off when an accident occurs.

Workbench •The workbench is stable enough.

•The workbench is reliably grounded.

Rack-mounting

requirements

•The rack has a good ventilation system.

•The rack is sturdy enough to support the weight of the

router and installation accessories.

•The size of the rack is appropriate for the router.

•The front and rear of the rack are a minimum of 0.8 m

(2.62 ft) away from walls or other devices.

Safety

precautions

•The router is far away from any moist area and heat source.

•The emergency power switch in the equipment room is located.

Tools •Installation accessories supplied with the router are available.

•User supplied tools are available.

Item

Requirements

Result

Reference •Documents shipped with the router are available.

•Online documents are available.

Autres manuels pour MSR 5600

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels H3C Routeur réseau

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C SR6600 SPE-FWM Manuel utilisateur

H3C

H3C SR6600 SPE-FWM Manuel utilisateur

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C SR6600 SPE-FWM Manuel d'installation

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C H3C MSR 30-20 ROUTER Manuel utilisateur

H3C

H3C MSR 20-20 Manuel utilisateur

H3C

H3C MSR Series Manuel d'installation

H3C

H3C MSR 2600 Series Manuel utilisateur

H3C

H3C MSR900-E Series Manuel utilisateur

H3C

H3C SR8800-F Manuel utilisateur

H3C

H3C MSR 5600 Manuel d'installation

H3C

H3C MSR830 Series Manuel utilisateur

H3C

H3C SR8800-X-S Manuel d'utilisation et d'entretien

H3C

H3C SR6604 Manuel utilisateur

H3C

H3C S12516CR Manuel d'utilisation et d'entretien

H3C

H3C MSR 5600 Manuel d'utilisation et d'entretien

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C H3C MSR 20 Manuel utilisateur

H3C

H3C H3C S3600 Series Manuel utilisateur

H3C

H3C SR8800 IM-FW-II Manuel d'installation

H3C

H3C H3C S7500E Series Instructions d'installation

H3C

H3C MSR Series Manuel d'installation

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité