H3C S3100-52P Manuel utilisateur

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Table of Contents

Table of Contents

Chapter 1 Port Basic Configuration ............................................................................................ 1-1

1.1 Ethernet Port Configuration...............................................................................................1-1

1.1.1 Initially Configuring a Port.......................................................................................1-1

1.1.2 Configuring Port Auto-Negotiation Speed...............................................................1-2

1.1.3 Limiting Traffic on individual Ports ..........................................................................1-3

1.1.4 Enabling Flow Control on a Port ............................................................................. 1-4

1.1.5 Duplicating the Configuration of a Port to Other Ports............................................1-4

1.1.6 Configuring Loopback Detection for an Ethernet Port ............................................1-5

1.1.7 Enabling Loopback Test..........................................................................................1-6

1.1.8 Enabling the System to Test Connected Cable......................................................1-7

1.1.9 Configuring the Interval to Perform Statistical Analysis on Port Traffic ..................1-8

1.1.10 Enabling Giant-Frame Statistics Function.............................................................1-8

1.1.11 Disabling Up/Down Log Output on a Port.............................................................1-8

1.1.12 Configuring Storm Control on a Port.....................................................................1-9

1.1.13 Setting the Port State Change Delay..................................................................1-10

1.1.14 Displaying and Maintaining Basic Port Configuration......................................... 1-12

1.2 Ethernet Port Configuration Example..............................................................................1-12

1.3 Troubleshooting Ethernet Port Configuration..................................................................1-13

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-1

Chapter 1 Port Basic Configuration

When performing port basic configuration, go to these sections for information you are

interested in:

zEthernet Port Configuration

zEthernet Port Configuration Example

zTroubleshooting Ethernet Port Configuration

Note:

zThe auto-negotiation speed configuration is added to this manual. For details, refer

to Configuring Port Auto-Negotiation Speed.

zThe storm control function is added to this manual. For details, refer to Configuring

Storm Control on a Port.

zThe displaying and maintaining of the statistics on dropped packets is added to this

manual. For details, refer to Displaying and Maintaining Basic Port Configuration.

zThe port state change delay configuration is added to this manual. For details, refer

to Setting the Port State Change Delay.

zDisable a port from generating UP/Down log is added to this manual. For details,

refer to Disabling Up/Down Log Output on a Port.

1.1 Ethernet Port Configuration

1.1.1 Initially Configuring a Port

Follow these steps to initially configure a port:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port

view interface interface-type

interface-number —

Enable the Ethernet

port undo shutdown

Optional

By default, the port is enabled.

Use the shutdown command

to disable the port.

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-2

To do... Use the command... Remarks

Set the description

string for the Ethernet

port description text

Optional

By default, the description

string of an Ethernet port is

null.

Set the duplex mode of

the Ethernet port duplex { auto |full |

half }

Optional

By default, the duplex mode of

the port is auto

(auto-negotiation).

Set the speed of the

Ethernet port speed { 10 |100 |1000

|auto }

Optional

zBy default, the speed of an

Ethernet port is determined

through auto-negotiation

(the auto keyword).

zUse the 1000 keyword for

Gigabit Ethernet ports only.

Set the medium

dependent interface

(MDI) mode of the

Ethernet port

mdi {across |auto |

normal }

Optional

Be default, the MDI mode of an

Ethernet port is auto.

Set the maximum

frame size allowed on

the Ethernet port to

9,216 bytes

jumboframe enable

Optional

By default, the maximum frame

size allowed on an Ethernet is

9,216 bytes. To set the

maximum frame size allowed

on an Ethernet port to 1,536

bytes, use the undo

jumboframe enable

command.

1.1.2 Configuring Port Auto-Negotiation Speed

You can configure an auto-negotiation speed for a port by using the speed auto

command.

Take a 10/100/1000 Mbps port as an example.

zIf you expect that 10 Mbps is the only available auto-negotiation speed of the port,

you just need to configure speed auto 10.

zIf you expect that 10 Mbps and 100 Mbps are the available auto-negotiation

speeds of the port, you just need to configure speed auto 10 100.

zIf you expect that 10 Mbps and 1000 Mbps are the available auto-negotiation

speeds of the port, you just need to configure speed auto 10 1000.

Follow these steps to configure auto-negotiation speeds for a port:

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-3

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet interface

view interface interface-type

interface-number —

Configure the available

auto-negotiation speed(s)

for the port

speed auto [ 10 |100 |

1000 ]*

Optional

zBy default, the port

speed is determined

through

auto-negotiation.

zUse the 1000 keyword

for Gigabit Ethernet

ports only.

Note:

zOnly ports on the front panel of the device support the auto-negotiation speed

configuration feature. And ports on the extended interface card do not support this

feature currently.

zAfter you configure auto-negotiation speed(s) for a port, if you execute the undo

speed command or the speed auto command, the auto-negotiation speed setting

of the port restores to the default setting.

zThe effect of executing speed auto 10 100 1000 equals to that of executing speed

auto, that is, the port is configured to support all the auto-negotiation speeds: 10

Mbps, 100 Mbps, and 1000 Mbps.

1.1.3 Limiting Traffic on individual Ports

By performing the following configurations, you can limit the incoming

broadcast/multicast/unknown unicast traffic on individual ports. When a type of

incoming traffic exceeds the threshold you set, the system drops the packets exceeding

the traffic limit to reduce the traffic ratio of this type to the reasonable range, so as to

keep normal network service.

Follow these steps to limit traffic on port:

To do... Use the command... Remarks

Enter system view system-view —

Limit broadcast traffic

received on each port broadcast-suppression

{ ratio | pps max-pps }

Optional

By default, the switch

does not suppress

broadcast traffic.

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-4

To do... Use the command... Remarks

Enter Ethernet port view interface interface-type

interface-number —

Limit broadcast traffic

received on the current

port

broadcast-suppression

{ ratio | pps max-pps }

Optional

By default, the switch

does not suppress

broadcast traffic.

Limit multicast traffic

received on the current

port

multicast-suppression

{ ratio | pps max-pps }

Optional

By default, the switch

does not suppress

multicast traffic.

Limit unknown unicast

traffic received on the

current port

unicast-suppression

{ ratio | pps max-pps }

Optional

By default, the switch

does not suppress

unknown unicast traffic.

1.1.4 Enabling Flow Control on a Port

Flow control is enabled on both the local and peer switches. If congestion occurs on the

local switch:

zThe local switch sends a message to notify the peer switch of stopping sending

packets to itself or reducing the sending rate temporarily.

zThe peer switch will stop sending packets to the local switch or reduce the sending

rate temporarily when it receives the message; and vice versa. By this way, packet

loss is avoided and the network service operates normally.

Follow these steps to enable flow control on a port:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Enable flow control on the

Ethernet port flow-control Required

By default, flow control is

not enabled on the port.

1.1.5 Duplicating the Configuration of a Port to Other Ports

To make other ports have the same configuration as that of a specific port, you can

duplicate the configuration of a port to specific ports.

Specifically, the following types of port configuration can be duplicated from one port to

other ports: VLAN configuration, protocol-based VLAN configuration, LACP

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-5

configuration, QoS configuration, GARP configuration, STP configuration and initial

port configuration. Refer to the command manual for the configurations that can be

duplicated.

Follow these steps to duplicate the configuration of a port to specific ports:

To do... Use the command... Remarks

Enter system view system-view —

Duplicate the

configuration of a port

to specific ports

copy configuration source

{ interface-type interface-number |

aggregation-group source-agg-id }

destination { interface-list

[ aggregation-group destination-agg-id ] |

aggregation-group destination-agg-id }

Required

Note:

zIf you specify a source aggregation group ID, the system will use the port with the

smallest port number in the aggregation group as the source.

zIf you specify a destination aggregation group ID, the configuration of the source

port will be copied to all ports in the aggregation group and all ports in the group will

have the same configuration as that of the source port.

1.1.6 Configuring Loopback Detection for an Ethernet Port

Loopback detection is used to monitor if loopback occurs on a switch port.

After you enable loopback detection on Ethernet ports, the switch can monitor if

external loopback occurs on them. If there is a loopback port found, the switch will put it

under control.

zIf loopback is found on an access port, the system disables the port, sends a Trap

message to the client and removes the corresponding MAC forwarding entry.

zIf loopback is found on a trunk or hybrid port, the system sends a Trap message to

the client. When the loopback port control function is enabled on these ports, the

system disables the port, sends a Trap message to the client and removes the

corresponding MAC forwarding entry.

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-6

Follow these steps to configure loopback detection for an Ethernet port:

To do... Use the command... Remarks

Enter system view system-view —

Enable loopback

detection globally loopback-detection

enable

Required

By default, loopback

detection is disabled

globally.

Set the interval for

performing port loopback

detection

loopback-detection

interval-time time Optional

The default is 30 seconds.

Enter Ethernet port view interface interface-type

interface-number —

Enable loopback

detection on a specified

port

loopback-detection

enable

Required

By default, port loopback

detection is disabled.

Enable loopback port

control on the trunk or

hybrid port

loopback-detection

control enable

Optional

By default, loopback port

control is not enabled.

Configure the system to

run loopback detection on

all VLANs of the current

trunk or hybrid port

loopback-detection

per-vlan enable

Optional

By default, the system

runs loopback detection

only on the default VLAN

of the current trunk or

hybrid port.

Caution:

zTo enable loopback detection on a specific port, you must use the

loopback-detection enable command in both system view and the specific port

view.

zAfter you use the undo loopback-detection enable command in system view,

loopback detection will be disabled on all ports.

1.1.7 Enabling Loopback Test

You can configure the Ethernet port to run loopback test to check if it operates normally.

The port running loopback test cannot forward data packets normally. The loopback

test terminates automatically after a specific period.

Follow these steps to enable loopback test:

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-7

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Enable loopback test loopback {external |internal }Required

Note:

zexternal: Performs external loop test. In the external loop test, self-loop headers

must be used on the port of the switch ( for 100M port, the self-loop headers are

made from four cores of the 8-core cables, for 1000M port, the self-loop header are

made from eight cores of the 8-core cables, then the packets forwarded by the port

will be received by itself.). The external loop test can locate the hardware failures on

the port.

zinternal: Performs internal loop test. In the internal loop test, self loop is established

in the switching chip to locate the chip failure which is related to the port.

Note that:

zAfter you use the shutdown command on a port, the port cannot run loopback

test.

zYou cannot use the speed, duplex, mdi and shutdown commands on the ports

running loopback test.

zSome ports do not support loopback test, and corresponding prompts will be given

when you perform loopback test on them.

1.1.8 Enabling the System to Test Connected Cable

You can enable the system to test the cable connected to a specific port. The test result

will be returned in five seconds. The system can test these attributes of the cable:

Receive and transmit directions (RX and TX), short circuit/open circuit or not, the length

of the faulty cable.

Follow these steps to enable the system to test connected cables:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Enable the system to test

connected cables virtual-cable-test Required

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-8

1.1.9 Configuring the Interval to Perform Statistical Analysis on Port Traffic

By performing the following configuration, you can set the interval to perform statistical

analysis on the traffic of a port.

When you use the display interface interface-type interface-number command to

display the information of a port, the system performs statistical analysis on the traffic

flow passing through the port during the specified interval and displays the average

rates in the interval. For example, if you set this interval to 100 seconds, the displayed

information is as follows:

Last 100 seconds input: 0 packets/sec 0 bytes/sec

Last 100 seconds output: 0 packets/sec 0 bytes/sec

Follow these steps to set the interval to perform statistical analysis on port traffic:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Set the interval to perform

statistical analysis on port

traffic flow-interval interval Optional

By default, this interval is

300 seconds.

1.1.10 Enabling Giant-Frame Statistics Function

The giant-frame statistics function is used to ensure normal data transmission and to

facilitate statistics and analysis of unusual traffic on the network.

Follow these steps to enable the giant-frame statistics function:

To do... Use the command... Remarks

Enter system view system-view —

Enable the giant-frame

statistics function giant-frame statistics

enable

Required

By default, the

giant-frame statistics

function is not enabled.

1.1.11 Disabling Up/Down Log Output on a Port

An Ethernet port has three physical link statuses: Up, Down, and Administratively Down.

For status transition conditions, refer to the description of the display brief interface

command in Basic Port Configuration Command.

Operation Manual – Port Basic Configuration

H3C S3100-52P Ethernet Switch Chapter 1 Port Basic Configuration

1-9

When the physical link status of an Ethernet port changes between Up and Down or Up

and Administratively Down, the switch will generate Up/Down log and send the log

information to the terminal automatically by default. If the status of Ethernet ports in a

network changes frequently, large amount of log information may be sent to the

terminal, which consumes more network resources. Additionally, too frequent log

information is not convenient for you to view.

You can limit the amount of the log information sent to the terminal by disabling the

Up/Down log output function on some Ethernet ports selectively. For information about

log output settings, refer to the Information Center module.

Follow these steps to disable UP/Down log output on a port:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Disable a port from

generating UP/Down log undo enable log

updown

Required

By default, UP/Down log

output is enabled.

1.1.12 Configuring Storm Control on a Port

The storm control function is used to control traffic received on an Ethernet port.

zWith traffic upper and lower thresholds specified on a port, the system periodically

collects statistics about the broadcast/multicast/unicast/ traffic on the port. Once it

finds that a type of traffic exceeds the specified upper threshold, it blocks this type

of traffic on the port or directly shuts down the port, and outputs trap/log

information according to your configuration.

zWhen a type of traffic on the port falls back to the specified lower threshold, the

system cancels the blocking of this type of traffic on the port or brings up the port to

restore traffic forwarding for the port, and outputs log/trap information according to

your configuration.

Follow these steps to configure storm control on a port:

To do... Use the command... Remarks

Enter system view system-view —

Enter Ethernet port view interface interface-type

interface-number —

Set the upper and lower

thresholds of

broadcast/multicast/unicast

traffic received on the port

storm-constrain

{ broadcast | multicast |

unicast } max-packets

min-packets pps

Required

Autres manuels pour S3100-52P

Table des matières

Autres manuels H3C Routeur réseau

H3C

H3C MSR 3600 Manuel utilisateur

H3C

H3C MSR 20 Series Manuel utilisateur

H3C

H3C S3100 Series Manuel utilisateur

H3C

H3C CR16000-F Manuel utilisateur

H3C

H3C CR19000-16 Manuel utilisateur

H3C

H3C SR8800 10G Manuel utilisateur

H3C

H3C S5560-EI series Manuel utilisateur

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C CR16000-F Manuel utilisateur

H3C

H3C MSR 5600 Manuel d'installation

H3C

H3C SR6600-X Manuel utilisateur

H3C

H3C S5510 Series Manuel utilisateur

H3C

H3C MSR 20-20 Manuel

H3C

H3C SR8803-F Manuel utilisateur

H3C

H3C MSR-20-21 ROUTER Manuel utilisateur

H3C

H3C S3100-52P Manuel utilisateur

H3C

H3C MSR 5660 Manuel d'utilisation et d'entretien

H3C

H3C MSR Series Manuel utilisateur

H3C

H3C MSR810 Manuel utilisateur

H3C

H3C MSR 20-20 Manuel d'installation

H3C

H3C MSR 5600 Manuel d'installation

H3C

H3C LS-5100-16P-SI-OVS-H3 Guide rapide

H3C

H3C SR8800-X Manuel utilisateur

H3C

H3C CR16000-F Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité