Greystone Energy Systems TXRCL Manuel utilisateur
TXRCL Temperature Transmitter with LCD Installation Manual
August 8, 2014 1
Introduction
The TXRCL transmitter incorporates a temperature transmitter
in an attractive wall mount enclosure for the most efficient
environmental monitoring and control system. It uses a curve-
matched thermistor to measure temperature. The device may
also include an occupancy override button and an external
communication jack. The output is available as a linear 4-20
mA, 0-5 or 0-10 Vdc signal.
An LCD is included for configuration and local indication of all
parameters. Several operating parameters can be programmed using a keypad for specific applications including four
temperature ranges and C/F display.
Before Installation
Read these instructions carefully before installing and commissioning the device. Failure to follow these instructions may
result in product damage. Do not use in an explosive or hazardous environment, with combustible or flammable gases, as a
safety or emergency stop device or in any other application where failure of the product could result in personal injury. Take
electrostatic discharge precautions during installation and do not exceed the device ratings.
Mounting
The room type sensor installs directly on a standard electrical box and should be mounted about five feet from the floor of the
area to be controlled. Do not mount the sensor near doors, opening windows, supply air diffusers or other known air
disturbances.
The cover is hooked to the base at the top edge and must be removed from the bottom edge first. Use a small screwdriver to
carefully pry each bottom corner if necessary. If a security screw is installed on the bottom edge, then it may have to be
loosened or removed also. Tip the cover away from the base and sit it aside.
The pcb must be removed from the base to access the mounting holes. Follow usual anti-static procedures when handling the
pcb and be careful not to touch or bend the sensors. The pcb is removed by pressing the tab on the enclosure base to unsnap
the latch near the bottom edge, then the pcb can be lifted out of the base. Sit the pcb aside until the base is mounted on the
wall.
After the base is screwed to an electrical box or the wall using the appropriate holes, pull the wires through the wiring hole in
the center of the pcb and then gently reinstall it in the enclosure base. Ensure the pcb is snapped into the base securely and
correctly. The mounting hole locations are shown in the following drawing.
TXRCL Temperature Transmitter with LCD Installation Manual
August 8, 2014 2
Wiring
Deactivate the 24 Vac/dc power supply until all connections are made to the device to prevent electrical shock or equipment
damage. Follow proper electrostatic discharge (ESD) handling procedures when installing the device or equipment damage
may occur.
Use 22 AWG shielded wiring for all connections and do not locate the device wires in the same conduit with wiring used to
supply inductive loads such as motors. Connect the cable shield to ground at the controller only. Make all connections in
accordance with national and local codes.
This is a sourcing device and requires 3 to 11 wires depending on features ordered. Connect the plus dc or the ac voltage hot
side to the POWER terminal. The power supply common is connected to the COMMON terminal. The device is reverse
voltage protected and will not operate if connected backwards. It has a half-wave power supply so the supply common is the
same as the signal common. Several devices may be connected to one power supply and the output signals all share the same
common. Use caution when grounding the secondary of a transformer or when wiring multiple devices to ensure the ground
point is the same on all devices and the controller.
The analog output is available on the TEMP OUT terminal. For 4-20 mA output type, all outputs operate in the Active mode
and do not require a loop power supply. This means the signal current is generated by the transmitter and must not be
connected to a powered input or device damage will result. Check the controller Analog Input to determine the proper
connection before applying power. All output signals are referenced to the COMMON terminal. The analog output signals
are typically connected directly to the Building Automation System and used as control parameters or for logging purposes.
The device is also available with 0-5 or 0-10 Vdc voltage signal outputs which connect directly to a high impedance analog
input. In either case the terminal designations are the same and the signals are referenced to COMMON.
The OCC IN terminal is a digital input that controls the OCC segment on the LCD to indicate an occupied condition. It can
be connected to a 0/5V digital signal or a dry contact signal. This is usually an active low input signal and requires that the
OCC IN terminal be shorted to COMMON to activate the input.
The override switch output is a dry-contact and is available on the SWITCH + and SWITCH – terminals. It is typically
connected to a low-voltage digital input on the controller to indicate room occupancy or override when the button is
activated.
The resistive fan speed output signal is available on the FAN + and FAN – terminals and has five positions.
The external jack is internally connected to a three-pin terminal block labeled RING, MID and TIP to accept a stereo phono
plug for remote communication with the controller.
Start-up
Verify that the transmitter is properly wired and connections are tight. Apply power and note that the LCD will begin
displaying the temperature levels. All the output signals will also be available immediately after start-up.
LCD Display
The device is configured to display the temperature continuously. The Setup Menu can be used to modify the displayed
information. The device supports four temperature ranges that may be selected in the menu. The default is 0-35 C but this
may be changed to 32-95 F and the output signal will stay the same. Also, the temperature range may be changed to 32-122
F or 0-50 C and the output signal scaling will change to match the display.
Output
The temperature output is scaled such that 4-20 mA (or 0-5 or 0-10 Vdc) equals either 0-35 C, 32-95 F, 0-50 C or 32-122
F depending on which range is selected in the menu. The factory default range is 0-35 C.
TXRCL Temperature Transmitter with LCD Installation Manual
August 8, 2014 3
Setup Menu
The menu has several items as shown below and the device cover must be removed to access the menu. To enter the menu,
press and release the <MENU> key while in normal operation. This will enter the Setup Menu step 1, pressing the <MENU>
key a second time advances to step 2. Each press of the <MENU> key advances the menu item. No values are changed by
using the <MENU> key but the previous value is saved, so any changes made will be saved by pressing the <MENU> key.
The <UP> and <DOWN> keys are used to make changes to program variables by scrolling through the available options.
When a value is changed, use the <MENU> key to save it to memory and advance to the next menu item.
Setup Menu operation is explained below and the factory default values are shown. Note that some items that are not
applicable to the hardware configuration are skipped in the menu so the menu may skip from item 4 to item 6 for example.
<MENU> Press and release the <MENU> key to enter the Setup Menu
1. C/F The temperature scale defaults to Celsius (°C). It can be changed to Fahrenheit
(°F) by using the <UP> or <DOWN> keys. This item is not shown for RH + RH
Setpoint models. This setting will effect other parameters.
<MENU>
2. Temperature Range
Two temperature ranges are available for both °C and °F, 0-35 C (32-95 F)
or0-50C (32-122 F). This can be changed with <UP> or <DOWN>.
<MENU>
3. Temperature Offset
Use<UP>or<DOWN>toaddorsubtract an offset to the temperature output
signal and display. The default is 0 but can be changed from –9 to +9 °F for
temperature calibration.
<MENU>
4. OCC Reverse
The default OCC signal type is active low (Lo). Can change with <UP> or
<DOWN> to active high (HI) to reverse the OCC action. By default, shorting
the OCC input to common will turn on the OCC LCD segment.
<MENU>
5. Backlight Enable
Usethe<UP>or<DOWN>keysto enable or disable the LCD backlight.
bL1 = backlight on, bL0 = backlight off.
<MENU> Exits the Setup Menu and returns to normal operation.
TXRCL Temperature Transmitter with LCD Installation Manual
August 8, 2014 4
Specifications
Temperature Sensor . . . . . . . . . . . . . . . . . . . 10K Ohm Type 7 Curve matched thermistor
Accuracy . . . . . . . . . . . . . . . . 0.2 C (0.4 C)
Range . . . . . . . . . . . . . . . . . . . 0 to 35 C (32 to 95 F) or 0 to 50 C (32 to 122 F) programmable
Offset . . . . . . . . . . . . . . . . . . . 9 F programmable
Display Units . . . . . . . . . . . . . C or F programmable
Display Resolution . . . . . . . . . 0.5° < 100°, 1° > 100°
Override Front panel push-button available as dry-contact two-wire output
N.O., 50 mA @ 12 Vdc
Communication 3.5 mm phono jack . . . . . . . . Connects to 3-pin terminal block (Ring, Tip, Mid)
Fan Speed Switch Range . . . . . . . . . . . . . . . . . . . Off, Auto, Low, Medium, High
Signal . . . . . . . . . . . . . . . . . . . 0, 2, 4, 6 and 8K standard, two-wire output (other values available)
Occupied Input Signal Type . . . . . . . . . . . . . . Digital input, 0/5 Vdc or dry contact to common
Logic . . . . . . . . . . . . . . . . . . . Active low or active high programmable
Action . . . . . . . . . . . . . . . . . . Causes “OCC” segment to light on LCD
LCD Display Display Size . . . . . . . . . . . . . . 38.1 x 16.5 mm (1.5” w x 0.65” h)
Digit Height . . . . . . . . . . . . . . 11.43 mm (0.45”)
Symbols . . . . . . . . . . . . . . . . . F, C, %RH, OCC
Backlight . . . . . . . . . . . . . . . . Enable or disable via menu
General Power Supply . . . . . . . . . . . . . 24 Vac/dc 10% (non-isolated half-wave rectified)
Consumption . . . . . . . . . . . . . . 40 mA max @ 24 Vdc
Input Voltage Effect . . . . . . . . Negligible over specified operating range
Protection Circuitry . . . . . . . . .Reverse voltage and MOV protected, output limited
Output Signals . . . . . . . . . . . . 4-20 mA active (sourcing) or 0-5/0-10 Vdc (specify when ordering)
Output Resolution . . . . . . . . . 10 bit
Output Drive Capability . . . . . 550 ohm max for 4-20 mA, 10 Kohm min for voltage
Programming and Selection . . Via pushbuttons and on-screen menu
Operating Conditions . . . . . . . 0 to 50 C (32 to 122 F), 0 to 95 %RH non-condensing
Wiring Connections . . . . . . . . Screw terminal block (14 to 22 AWG)
Enclosure . . . . . . . . . . . . . . . . Wall mount, 84 x 117 x 29 mm (3.3”w x 4.6”h x 1.15”d)
TXRCL Temperature Transmitter with LCD Installation Manual
August 8, 2014 5
Terminal Function
POWER From +24 Vac/dc of controller or power supply
COMMON To GND or COMMON of controller
OCC IN From digital output of controller
TEMP OUT Temperature output to analog input of controller
4-20 mA or 0-5/0-10 Vdc
SWITCH + Override switch + to digital input of controller
SWITCH - Override switch - to COMMON of controller
FAN + Fan speed switch + to analog input of controller
FAN - Fan speed switch - to COMMON of controller
TIP External jack TIP (tip of plug) connection
MID External jack MID (middle of plug) connection
RING External jack RING (base of plug) connection
Table des matières
Autres manuels Greystone Energy Systems Émetteur
Greystone Energy Systems
Greystone Energy Systems ULP1 Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems ELP-S Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CMD5B1 010 Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CD2DT Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CD2RMC Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems TE500AD Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems PMRMC Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HRC Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HATXFL Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HSOB Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CDD3B1 Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems NDD Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CDD4 Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CDD4B1 Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems TDAP Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CDD4A1 Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HAHRC Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems CMD5B4 Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HATDFL Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems DP Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems GDT Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems AVDT Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HATXSO Series Manuel utilisateur
Greystone Energy Systems
Greystone Energy Systems HATXOB Series Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
