Graco Therm-O-Flow 194485 Manuel d'utilisation

Instructions–Parts List

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

Therm–O–FlowR

Automatic Dispense Valves

Air–operated dispense valves. For professional use only.

Model 918483 Shown

310538L

ENG

2 310538

Table of Contents

List of Models 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warnings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimensions 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Standard Warranty 48. . . . . . . . . . . . . . . . . . . . . .

Graco Information 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

List of Models

Valve

Type Part

No. Type Voltage /

No. of Pins Maximum Fluid Working

Pressure Maximum Air Input

Pressure Parts

Page

TOF 194485 Snuff Back 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 20

TOF 918483 Snuff Back 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 22

918512 Snuff Back Ambient 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 24

TOF 918639 Snuff Back 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 26

TOF+ 243694 Base Seal 240 V / 8 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 28

TOF 200 297266 Snuff Back Swirl 240 V / 8 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 30

TOF+ 243695 Base Seal H.F. 240 V / 8 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 31

TOF+ 243696 Snuff Back 240 V / 8 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 33

TOF C27340 Base Seal Ambient 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 35

TOF C34068 Base Seal 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 37

TOF C34079 Base Seal 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 39

TOF C50592 Base Seal 120 V / 6 241 bar, 24 MPa (3500 psi) 10 bar, 1 MPa (150 psi) 41

310538 3

Warnings

The following Warnings are for the safe setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure–specific risks.

Refer back to these Warnings. Additional product–specific warnings may be found throughout the body of this

manual where applicable.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and

result in serious injury.

DThis equipment is for professional use only.

DRead all instruction manuals, warnings, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are uncertain, call your Graco distribu-

tor.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck the equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum air working pressure of 1 MPa (10 bar, 150 psi) to the applicator.

DDo not exceed the maximum fluid working pressure of 24 MPa (241 bar, 3500 psi) to the

applicator or manifold.

DNever exceed the recommended working pressure or the maximum air inlet pressure stated on

your pump or in the Technical Data on page 47.

DBe sure that all spray/dispensing equipment and accessories are rated to withstand the maxi-

mum working pressure of the pump. Do not exceed the maximum working pressure of any

component or accessory used in the system.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces.

DDo not expose Graco standard hoses to temperatures above 180_F (82_C) or below –40_F

(–40_C). Do not expose Graco electrically heated hoses to temperatures above 400°F

(222°C) or below –40_F (–40_C).

DDo not expose Graco standard hoses to temperatures above 180_F (82_C) or below –40_F

(–40_C).

DDo not use the hoses to pull the equipment.

DUse only fluids and solvents that are compatible with the equipment wetted parts. See the

Technical Data sections of all the equipment manuals. Read the fluid manufacturer’s warnings.

DAlways wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid

and solvent manufacturers.

DWear hearing protection when operating this equipment.

DComply with all applicable local, state and national fire, electrical and other safety regulations.

4 310538

WARNING

HOT SURFACE AND FLUID HAZARD

Heated fluid can cause severe burns and can cause equipment surfaces to become very hot.

DWear protective gloves and clothing when operating this equipment in a heated system.

DDo not touch the metal heat sink when the surface is hot.

DAllow the equipment to cool thoroughly before servicing.

Some heated systems are designed to dispense Polyurethane (PUR) heated materials. PUR

systems are supplied with ventilation hoods, and require proper ventilation and specially designed

system components.

SKIN INJECTION HAZARD

Spray from the applicator, hose leaks, or ruptured components can inject fluid into your body and

cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on

the skin can also cause serious injury.

DFluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate

surgical treatment.

DDo not point the applicator at anyone or at any part of the body.

DDo not put hand or fingers over the front of the applicator.

DDo not stop or deflect fluid leaks with your hand, body, glove, or rag.

DFollow the Pressure Relief Procedure on page 11 whenever you are instructed to: relieve

pressure; stop dispensing; clean, check, or service the equipment; or install or clean a tip or

nozzle.

DTighten all the fluid connections before operating the equipment.

DCheck the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immedi-

ately. Permanently coupled hoses cannot be repaired; replace the entire hose.

DALWAYS wear eye protection and protective clothing when installing, operating, or servicing this

dispensing equipment.

DDo not remove or modify any part of the applicator; this can cause a malfunction and result in

serious bodily injury.

DUse extreme caution when cleaning or changing tips. If the tip clogs while applying material,

ALWAYS follow the Pressure Relief Procedure on page 11, then remove the tip to clean it.

DNEVER wipe off build-up around the tip or air cap until pressure is fully relieved.

310538 5

WARNING

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD

Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition

and result in fire or explosion and serious injury.

DGround the equipment and the object being sprayed. The Automatic Dispense Valve is

grounded through proper connection of pin E inside the electrical control panel to truth earth

ground inside the electrical control panel. See Grounding on page 9.

DGround the equipment and the object being sprayed, and all other electrically conductive

objects in the dispense area. Proper grounding dissipates static electricity generated in the

equipment. See Grounding on page 9.

DDo not use this equipment with flammable liquids.

DKeep the dispense area free of debris, including solvent, rags, and gasoline.

DIf there is any static sparking or you feel an electric shock while using the equipment, stop dis-

pensing immediately. Do not use the equipment until you have identified and corrected the

problem.

DMake sure all electrical work is performed by a qualified electrician only.

DHave any checks, installation, or service to electrical equipment performed by a qualified electri-

cian only.

DMake sure all electrical equipment is installed and operated in compliance with applicable

codes.

DMake sure power is disconnected when servicing and repairing equipment.

DBefore operating the equipment, extinguish all open flames or pilot lights in the dispense area.

DDo not smoke in the dispensing area.

DKeep liquids away from the electrical components

DDisconnect electrical power at the main switch before servicing the equipment.

DNever exceed maximum wattage of the supply unit.

TOXIC FLUID HAZARD

Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the

skin, swallowed, or inhaled.

DProvide fresh air ventilation to avoid the buildup of vapors from the fluid being dispensed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all

local, state and national guidelines.

DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid

and solvent manufacturer.

DAvoid exposure to heated material fumes.

6 310538

Installation

Install the automatic applicator as follows:

Dmount the automatic dispense valve

Dattach dispense tip, nozzle, or swirl

Dconnect the air lines

Dconnect material hose

Dconnect the electrical cable

Dmake sure the automatic dispense valve is

grounded

Mount the Automatic Dispense Valve

Mount the automatic dispense valve to the mounting

bracket on a stationary support or robotic arm (Fig. 1),

using two socket head screws (300) and two flat

washers (50). Be sure to position the insulation

block (280) and insulation tape (290) between the

dispense valve and the mounting bracket.

Fig. 1

300

280

290

Attach Dispense Tip, Nozzle, or Swirl

Attach a dispense tip and a nozzle adapter, or a nozzle

adapter alone, to the automatic dispense valve.

Dispense Tip and Nozzle Adapter Attachment

Attach dispense tip (B) to the automatic dispense

valve.

1. Select a nozzle adapter (C) and a dispensing

tip (B).

2. Install the tip and then use the nozzle adapter (C)

to secure the tip to the seat adapter (D).

Fig. 2

310538 7

Installation

Nozzle Attachment

Attach a nozzle (C) to the automatic dispense valve.

1. Select a nozzle.

2. Install nozzle adapter (C) on the seat adapter (D).

3. Install nozzle in nozzle adapter (E).

Fig. 3

Swirl Nozzle Attachment

1. Install swirl adapter (C) on seat adapter (D).

2. Install swirl applicator head (E).

3. Install swirl nozzle (F).

Fig. 4

8 310538

Installation

Connect Air Lines to Dispense Valve

CAUTION

Only use air fittings that are rated at a temperature

equal to or higher than the operating temperature of

your fluid dispensing system. Lower rated air fit-

tings could melt and cause damage to the automat-

ic dispense valve.

These valves are air to open and air to close with a

spring to bias them closed. Use a 4–way exhausting

solenoid to operate these valves.

Making sure to connect the appropriate air lines to the

appropriate ports (see Fig. 5), securely connect air

lines to dispense valve air ports (G).

Connect Material Hose to Dispense Valve

Securely connect the material hose to the dispense

valve material inlet port (A). See Fig. 5.

Connecting Electrical Cable to Dispense

Valve

Connect electrical cable plug from your Therm–O–

Flow or Therm–O–Flow Plus hose or control.

Fig. 5

1/2” npt

360

open

1/8” npt

Snuff–Back Valve Shown

310538 9

Installation

Grounding

WARNING

FIRE, EXPLOSION, AND ELECTRIC

SHOCK HAZARD

To reduce the risk of fire, explosion, or

electric shock:

DThe power source conduit is not an ad-

equate ground for the system. The unit

must be grounded to either the building

ground or a true earth ground.

DA qualified electrician must complete

all grounding and wiring connections

and check the resistance.

DRefer to your local code for the requirements for

a “true earth ground” in your area.

DAlso read and follow the warnings on page 5.

Ground the automatic dispense valve:

1. Connect the connector from a heated hose to the

receptacle on the dispense valve.

Fig. 6

Ground lead

coming from pin

E is fastened to

the bracket. A

Fig. 7

Ground lead

coming from con-

tact 8 to true

earth ground.

TI0305

2. Connect the electrical cable to the electrical control

panel.

3. Verify that socket contact E on six pin models (see

Fig. 5) or contact eight on eight pin models (see

Fig. 7) , inside control panel receptacle, is con-

nected to true earth ground.

10 310538

Troubleshooting

Some solutions require disassembling the automatic dispense valve. Always relieve system pressure before per-

forming these procedures.

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow

the Pressure Relief Procedure (page 11).

See PARTS section for the parts that need to be serviced.

Problem Cause(s) Solution(s)

Air leaks from automatic dis-

Loose air connections Check air connections.

pense valve Worn o-rings Replace o-rings (90) and (100) in cylin-

der base.

Worn ring Replace ring (110) in cylinder base.

Material leaks from front of

automatic dispense valve

Seal, spacer or retaining ring is worn Replace rod seal (150), spacer (160),

and retaining ring (170).

Obstruction inside dispense valve Remove seat adapter (10). Check and

replace if necessary, rod seal (150),

spacer (160), and retaining ring (170).

Worn needle Check and replace needle (140), if

necessary.If replacing needle, you must

disassemble dispense valve.

Worn seat (Base seal models) Check and replace seat (10) if neces-

sary.

Material leaks from automatic

di l b d

Seal not installed correctly Check seal (70) and replace if neces-

dispense valve body Seal is worn sary.

Automatic dispense valve

does not shut off

Loose air connections Check air connections.

does not shut off Worn needle-seal interface Check and replace, if necessary, needle

(140), rod seal (150), spacer (160), and

retaining ring (170).

retaining

ring

(170)

If replacing needle, you must disas-

semble dispense valve

Automatic dispense valve

does not shut off

Worn spring-piston interface Disassemble dispense valve. Check

and replace, if necessary, needle (140),

and spring (370).

Automatic dispense valve

does not shut off

Spring broken or not installed correctly Disassemble dispense valve. Check

and replace, if necessary, needle (140),

and spring (370).

Automatic dispense valve

dthttil

Loose heater wires Check and reconnect wire connections.

does not heat material Loose sensor wires Check and reconnect wire connections.

Heater unit failed Replace heater. See page 17.

Sensor failed Replace sensor. See page 17.

Temperature controller failed Replace temperature controller.

No power to heating circuitry Apply power to heating circuitry.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Unité de contrôle

Graco

Graco Gun Flush Box 570046 Manuel d'utilisation

Graco

Graco PD44 Instruction manuelle

Graco

Graco Gun Flush Box 244105 Manuel d'utilisation

Graco

Graco Pulse 25D130 Manuel

Graco

Graco 256653 Manuel utilisateur

Graco

Graco SDP8 Series Manuel du propriétaire

Graco

Graco E-Flo B Series Manuel de la liste des pièces

Graco

Graco 10:1 Dyna-Star 247444 Manuel d'utilisation et d'entretien

Graco

Graco E-Flo 24P821 Manuel d'utilisation

Graco

Graco PD44 Instruction manuelle

Graco

Graco 244912 Manuel d'utilisation

Graco

Graco CleanShot Manuel utilisateur

Graco

Graco L20c Manuel de la liste des pièces

Graco

Graco Modbus TCP Manuel utilisateur

Graco

Graco LDP5 Manuel utilisateur

Graco

Graco 571169 Manuel utilisateur

Graco

Graco Dyna-Star 25U218 Manuel utilisateur

Graco

Graco Pro-Shot A Series Manuel utilisateur

Graco

Graco PM5 238501 Manuel d'utilisation

Graco

Graco ProGuard+ Manuel utilisateur

Graco

Graco Dispensit 710 Manuel utilisateur

Graco

Graco 208390 Manuel utilisateur

Graco

Graco B52100 Manuel de la liste des pièces

Graco

Graco 15X303 Manuel de référence technique

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

Flyron

Flyron FN-BC04 Manuel utilisateur