Graco 1093 Instruction manuelle

3A0261K

Setup - Operation

1053/1093

Control Box

Patented meter and dispense system for precise one-component micro-dispensing. Not

for use in explosive atmospheres.

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

CONTROL POWER

23A0261K

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Component Identification . . . . . . . . . . . . . . . . . . . . 6

Control Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Valve Connection Kits . . . . . . . . . . . . . . . . . . . . . . . 9

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Motor Driven . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjust Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Dispensing Operation . . . . . . . . . . . . . . . . . . . . . . 16

HMI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Screen Navigation Diagrams . . . . . . . . . . . . . . 17

Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Metering Valve Control Screen . . . . . . . . . . . . . 19

Shot Size Screen . . . . . . . . . . . . . . . . . . . . . . . 21

Level 1 Control Screen . . . . . . . . . . . . . . . . . . . 22

Level 2 Control Screen . . . . . . . . . . . . . . . . . . . 23

Purge Timer Screen . . . . . . . . . . . . . . . . . . . . . 25

Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Motor Status Screen . . . . . . . . . . . . . . . . . . . . . 28

Supervisor Screen . . . . . . . . . . . . . . . . . . . . . . 29

Supervisor Help Screen . . . . . . . . . . . . . . . . . . 31

Motor Error Codes Screen . . . . . . . . . . . . . . . . 32

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 33

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Customer Inputs/Outputs . . . . . . . . . . . . . . . . . . . 34

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 42

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 42

Related Manuals

3A0261K 3

Related Manuals

Component manuals in U.S. English.

Part Description

313566 Dispensit 1093

313812 Dispensit 1053-10B

334001 1053 Valve 24V Solenoid Replacement Kit,

Instructions

334002 1093 Valve 24V Solenoid Replacement Kit,

Instructions

Warnings

43A0261K

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back

to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where

applicable.

WARNING

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

swallowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

• Always wear impervious gloves when spraying or cleaning equipment.

• If this equipment is used with isocyanate material, see additional information on isocyanates in Iso-

cyanate Conditions Section of this manual.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic

fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eyewear

• Clothing and respirator as recommended by the fluid and solvent manufacturer

• Gloves

• Hearing protection

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes

are present.

• Ground all equipment in the work area. See Grounding instructions.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-

tric shock.

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors.

Warnings

3A0261K 5

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and

cause serious injury.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,

checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment

and follow the Pressure Relief Procedure in this manual when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many

solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property

damage. See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent

manufacturer’s warnings.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe

burns:

• Do not touch hot fluid or equipment.

WARNING

Component Identification

63A0261K

Component Identification

Control Boxes

Power input/fuse holder, 81/0365-3/11, can be set to either 115V or 230V. To determine what voltage it is currently

set to, look at the port and read what is showing through the cover window. To switch voltage, open the fuse holder

cover with a small screwdriver, pull the fuse holder out, flip the fuse holder 180°, push the fuse holder back in, and

snap the fuse holder cover back into place.

NOTE: Fuse part number: V-21610P

120 V power cord part number: 81/1051-1/11

240 V power cord part number: 121054

FIG. 1: Motor Driven Control Box

Key:

A Emergency Stop

B Control Power Switch

C Touch Panel

D Alarm Speaker

E Power Input

F Start Options Connection

H A Tank Level Controls Connection

J B Tank Level Controls Connection

K Customer Signal Terminals

L Dispense Valve I/O Connection

M Foot Switch

U Motor Connection

H,J

Component Identification

3A0261K 7

Valve

FIG. 2: Valve

Key:

AA Motor Release Knob

AB Motor

AC Amplifiers Up/Home/Down

AD Prox-Photo Reflecting Sensor Up

AE Prox-Photo Reflecting Sensor Home

AF Prox-Photo Reflecting Sensor Down

AG Metering Rod Stroke

AD, AE

Grounding

83A0261K

Grounding

This product must be grounded. In the event of an elec-

trical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric cur-

rent.

Grounding plug units: this product is equipped with a

cord having a grounding wire with an appropriate

grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded in accordance

with all local codes and ordinances.

Hard-wired units: the grounding wire must be used. All

electrical wiring must be done by a qualified electrician

and comply with all local codes and regulations.

Air and fluid hoses: use only electrically conductive

hoses.

Fluid supply container: follow local code.

Solvent pails used when flushing: follow local code.

Use only conductive metal pails, placed on a grounded

surface. Do not place the pail on a non-conductive sur-

face, such as paper or cardboard, which interrupts

grounding continuity.

Kits

NOTE: 80/2957-1/50 1053/1093 control requires three

sensor switches to operate. Valve, control, and connec-

tion kits are sold separately. Some assembly required.

Mounting adapter kit 24V674 may be required for

mounting the solenoid to the 1053 valve.

‡ Mounting side plate 01/2983/97 may be required for

mounting the solenoid to the 1093 valve.

Part Description

24E846Connection kit; for 1053 models that include

1 switch

24E845Connection kit; for 1053 models that include

2 switches, including the following assem-

blies:

A2A10007, A2A10008, A2A10009,

A2A10010, A2A10011, A2A1001,

A2A10015, A2A10016, A2A10018,

A2A10019, A2A10020, A2A10200,

A2A10300, A2A10301, A2A10302,

A2A10303, A2A10304, A2A10305,

A2A10306, A2A10307, A2A10308,

A2A10309

24E847‡ Connection kit; for 1093 models, including

the following assemblies:

A2A05401, A2A05402, A2A05403,

A2A05404, A2A05405, A2A05406

Valve Connection Kits

3A0261K 9

Valve Connection Kits

These valve connection kits enable certain valves to be used with this control package. Each kit contains the

mechanical, electrical, and pneumatic hardware needed to install the valve. See associated drawing for hardware

location and wiring information.

24E845, 1053 Dispense Valve with Added

Up and Down Validation/Actuation Kit

NOTE: PX-HOME must be below PX-UP. PX-HOME

may have been supplied in top hole. If so move to the

appropriate location as shown.

18,

4, 5

26,

14, 15, 16

19,

20,

SOL-CSV

SOL-OSV

LS-CSV

LS-OSV

AMP-D

AMP-U

AMP-HOME

PG-2

PX-HOME

PX-D

PX-U

Valve Connection Kits

10 3A0261K

24E845 Electrical socket schematic

Ref Part Description Quantity

196/0098/99 SCREW, socket head, 10-24x1.50 2

216C798 PLATE, mounting, 1053, dsub, 15 pin 1

3ADM00022 COVER, connector, dsub, 15p, 45deg 1

481/0360-N/11 SCREW, jack, connector, dsub, type a 2

5B2050001 NUT, allen, 4-40, alloy 2

6297331 SCREW, cap, 4x1/4 2

14 81/1265/11 BRACKET, end 2

15 297639 SCREW, cap, button head 2

16 81/0283-DIN/11 RAIL, din 0.01

17 F0200075 CABLE, prox-photo 2

18 81/0378-2/25 STRAP, ground, ring, #10, 16ga 1

19 100166 NUT, full hex 1

20 96/0005-2/99 WASHER, lock, ext, #10 1

21 84/0130-25/11 LABEL, prot earth(grnd).375x.375 1

22 16D050 AMPLIFIER, 1chan, photo, pnp, 24vdc 2

23 94/0740-A/99 FITTING, elbow, swivel, 1/4tubex10-32 2

24 127629 VALVE, solenoid, 4 way, 3 position, 24V 1

25 82/0217-A/11 MUFFLER, air, 1/8 NPT 2

26 127632 SCREW, socket head, 4-40x1.00 2

27 94/0705-1/96 FITTING, elbow, swivel, 1/4 tube 3

28 17A412 WASHER, split, #4 2

WLDB(H

%/$&.

5('

%/$&.

5('

%/.

%51

%/8

%51

%/8

%/.

%/8

%51

%/.

5('

%/.

5('

*51

,1&/8'(':,7+%$6(9$/9(

:+,7(

%52:1

:+7

%51

%/8

%51

%/8

%51

,1&/8'(':,7+%$6(9$/9(

+22.83)2586:,7&+

,1&/8'(':,7+%$6(9$/9(

+22.83)25)6:,7&+





















&211(&7,21729$/9(&21752/6

3,1'68%&211(&7253*











62/269

62/&69

$03'

$038

$03+

3;8

3;'

3;+







/6269

/6&69







/6269

/6&69









Autres manuels pour 1093

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Unité de contrôle

Graco

Graco Therm-O-Flow 25C994 Manuel utilisateur

Graco

Graco Cleanshot 244162 Manuel utilisateur

Graco

Graco Dyna-Star 24Y408 Manuel d'utilisation et d'entretien

Graco

Graco ProGuard+ Manuel utilisateur

Graco

Graco 24J415 Manuel de la liste des pièces

Graco

Graco DynaMite 224906 Manuel d'utilisation

Graco

Graco E 208997 Manuel d'utilisation

Graco

Graco USP Manuel utilisateur

Graco

Graco CGM Manuel de la liste des pièces

Graco

Graco Dispensit 1052 Guide de dépannage

Graco

Graco 10:1 Dyna-Star 247444 Manuel d'utilisation et d'entretien

Graco

Graco PR70 Series Manuel

Graco

Graco Gun Flush Box 570046 Manuel d'utilisation

Graco

Graco CleanShot 244160 Manuel de la liste des pièces

Graco

Graco PD44 Mode d’emploi

Graco

Graco Dyna-Star 77X540 Manuel utilisateur

Graco

Graco 244920 Manuel d'utilisation

Graco

Graco PrecisionFlo 233678 Manuel d'utilisation

Graco

Graco L20c Manuel de la liste des pièces

Graco

Graco Pulse 25D130 Manuel

Graco

Graco SERIES F Manuel d'utilisation

Graco

Graco PM5 238501 Manuel d'utilisation

Graco

Graco Control Architecture Module Manuel du propriétaire

Graco

Graco 482 Series Manuel d'utilisation

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

Flyron

Flyron FN-BC04 Manuel utilisateur